User's Manual

ManualsBrandsJiangsu Puhui Huida communication equipment ManualsElectronicsCeiling Mount AP

1.Use Laptop or mobile phone to test whether the wireless network can surf the

Internet: click wireless network , select the wireless SSID, enter the

password, test whether you can surf the Internet.

2.Check the status of the wireless network connection, signal quality, signal

speed, transmission and data rate: click on the details, check if the IP address

and DNS server address, etc., obtained correctly, confirm that the device is

working properly.

Reboot Modify Password Upgrade Time LogConfigure

Configure

Backup

Restore

Reset Default

Save the configuration file to your computer

Restore the factory default settings ,please press this button

Select

Users can backup,reboot and reset to factory default settings through device

management menu options, together with modify the WEB login password,

upgrade firmware, time synchronization and system log statistics and other

functional settings.

Configuration Management

4.4

Wireless testing

4.5

Gateway Mode

Realize router function, WAN port connect with modem (ADSL cat or Fiber

cat) to dial-up, or WAN port dynamic, static IP address to surf the internet.

Repeater mode

Enables wireless bridge and forwarding without compatible matching with

the upper device.

WISP Mode

Wireless ISP clients connect to the wireless base station by wireless, to

achieve local LAN sharing.

AP mode

Under this mode, NAT, DHCP, firewall, and all WAN related functions are

turned off, all wireless and wired interfaces are bridged together, no

distinguishing between LAN and WAN.

Based on the Quick Setup Wizard for each mode shown in the above

picture, Set the parameters and options that user needs, and click Next

step until the settings for each operation mode are completed .

Operation mode setup

Other mode

4.6

POE SwitchAC

Laptop Mobile phone Monitor

AP1 AP2 AP3

Router

Cloud Server

INTERNET

Bypass mode topology

AC Gateway mode topology

Laptop Mobile phone Monitor

AP1 AP2 AP3

Cloud Server

INTERNET

AC(AC gateway all in one)

POE Switch

Tips: If the AP support 24V PoE, pls use 24V PoE switch or Poe adapter; if the AP

is a standard active 48V PoE device Please use a switch that supports IEEE802.3at

standards.When deploy a large wireless network, there are many APs in this

network, recommend use an ACwireless controller in the network to centrally

manage all AP in the network.

Ports & Buttons

LED Indicator

Ports Instructions

Reset

WAN

LAN

Led indicator will be bright when Ethernet cable is connected

DC Power port

Reset button,will make device revert to factory settings ,press it for 10 seconds when powered,device will reboot

Connect WLAN internet, WAN port connect to ADSL modem or community broadband cable. Under AP,

repeater mode, WAN port will be changed to LAN port

LAN port which can connect LAN device

LED indicator instructions

Ports Instructions

BackFront

* The interface for different models of products may be different, the above diagram is only for reference ,

pls refer to the actual product !

*The number of LEDs for different models of ceiling mount AP will be different, please refer to the actual product.

System Light

2.4G Light

Bright

Flashing

System boots up successfully

2.4G Wireless boots up successfully

System reset default

Thress LED Indicator

System boots up successfully

WIFI boots up successfully

Instruction

System Light/WIFI

Green Light

Blue light

One LED Indicator

Name Normal Status

Instruction

Name Normal Status

Operational environment

Only Suitable for safe use in

non-tropical climatic conditions.

Suitable for safe use in areas

below to 2000 meters based on sea level

2000m≤

LAN RST

LED

Indicator

WAN

Indicator

WAN/POE

1/Product introduction

2/Device installation 3/Device connection

5.In AP setup page,choose “Get IP from AC” in connection type,choose next step.

6. In Wifi setup page,set up as the picture shows below:

√

LAN Settings

IP Mode

Get IP From AC

Static IP

Get IP From Gateway

AP Mode

√

2G WIFI Setting

AP Mode

Wifi Status

Hide your SSID?

SSID

Wireless2.4G

Channel

Encrypt Open

Timing 1 Day

20M Auto

NextBack

7.Setup completed

IP settings: After the configuration is completed, the wireless AP will restart and

enter the working status you set. Then change the IP address of your computer to

automaticacquisition, computer and other wireless devices can connect to the

previous router via a wireless AP for wireless Internet access.

View status

: Manually set an fix IP address for your computer to 192.168.188.X (X is

number of 2-252) , access into wireless AP IP address, login to view management

status, as shown in the following picture.

√

AP模式

AP Mode

Have completed your configuration！

Internet setup and Status

4.3

Connect to PC by wireless

Connect PC by wired

Using the wired connection, set the IP address of the TCP/IP property of the wired

network card to 192.168.188.X (X is number of 2---252), the PC will be the same IP

segment as AP.

Web login Management

3. FAT AP mode home page is as below:

4.Setup Wizard page,choose AP mode as the current working mode.

Operation Mode AP Mode Fat AP

Uptime 01:05:39

Click Settings

CPU Usage 1%

Memory Usage 20%

Device Information

WIFI Information

Device Description LAN Information

IP Mode

Lan IP

Subnet

AC Address

MAC Address

Get IP From AC

192.168.188.253

255.255.255.0

172.16.0.1

44:D1:FA:75:BF:3F

Status

SSID

Channel

Encrypt

MAC Address

Wireless-2.4G

Open

44:D1:FA:75:BF:41

Operation Mode AP Mode Fat AP

Uptime 01:05:39

Click Settings

CPU Usage 1%

Memory Usage 20%

Device Information

WIFI Information

Device Description LAN Information

IP Mode

Lan IP

Subnet

AC Address

MAC Address

Get IP From AC

192.168.188.253

255.255.255.0

172.16.0.1

44:D1:FA:75:BF:3F

Status

SSID

Channel

Encrypt

MAC Address

Wireless-2.4G

Open

44:D1:FA:75:BF:41

In this mode the AP wireless interface and cable interfac

are bridging together.Without NAT,firewall and all network

related functions.

Gateway Repeater Mode WISP Mode

Current Mode

AP Mode

1.Use Internet Explorer to visit http://192.168.188.253, pop up the login screen shown

in the following picture, the default login password: admin, after completing it will

go to the wireless AP settings page.

2.Default is fit AP mode page, users need to click the button at the right corner

to change it to FAT AP mode if need.

Apply Reset Reboot

Information

Settings

IP Address

Subnet

Mac Address

Gateway

AC Address

192.168.188.253

255.255.255.0

44:D1:FA:75:BF:3F

192.168.188.1

172.16.0.1

IP Mode DHCP

瘦AP模式

AP mode

4/Device management

(2)、After setting the IP address, make user connect with device in wireless,

double-click "Wireless network Connection" in the pop-up wireless SSID list,

select "Wireless 2.4G", click "Connect", enter the password in the pop-up

password box, the default password is "66666666", click "OK" to complete the

connection.

(1)、To connect a device wirelessly, you need to set the IP address of the TCP/IP

property of the wireless network card to 192.168.188.X (X is number of 2--252)

first, so that the device and PC in the same IP segment, and set the subnet mask

to 255.255.255.0, as shown in the following picture:

5/Use mobile phone to login

*This manual is only used for instructions and provide an accurate as we can ,

but can not make sure all the information in this manual is correct .This manual may be

updated because of the products upgrade,we have the right to revise the manual without any notice .

Open the phone click "settings", choose "WLAN" , find and long press the SSID,

pop-up menu select "Static IP", set an static IP 192.168.188.X (X can not be 253 or

252) (the static IP should be same IP segment in AP) for mobile phone, then input

the right Gateway IP, network mask and domain name.

Click "settings", choose "WLAN", click exclamation mark after connect wireless

signal successfully ,setup the static IP 192.168.188.X(X can not be 253 or 252) for

mobile phone, then input gateway IP, subnet mask and DNS, please note: the static

IP should be in the same IP segment of AP

How to set static IP for IOS system mobile phoneHow to set static IP for Android system mobile phone

Mobile phone login page of AP (login password is admin) When mobile phone connect to AP through wireless, need to configure static IP as below step

Use mobile phone to login

5.1

折

位

线

折位线

折

位

线

折

位

线

折

位

线

折位线

折

位

线

折

位

线

PJ-SMSX-xxx

Ceiling Mount AP User Manual

Common Problem and Solution

Q1: Forget login name and password ?

A1: Reset to factory default: press the reset button for 10 seconds and release it , the

device willreboot and revert to factory default settings

Q2: Can not Login wireless AP management through WEB page ?

A2: 1.Check if PC with static IP and if this IP is in the same IP segment of AP, make sure

not setto other IP range.

2.Reset AP and re-connect to AP.

3.Make sure wireless AP IP address is 192.168.188.253 and not occupied by other

devices .

4.Check if there is something wrong with PC and Ethernet cable ,recommend to use

CAT 5 Unshielded Twisted cable .

Q3: Forget wireless network password ?

A3: 1.Connect AP by wired ,login WEB management page-click wireless settings- basic

settings-password-set a new password for wireless network.

2.Reset it , the default password is 66666666.

Q4: Can not get IP Address ?

A4: 1.Under gateway and WISP mode, check if DHCP server is on

2.Under repeater and AP mode, check if upper network connection is normal ,or if LAN

network DHCP server is working well .

Q5: How to change FIT AP to FAT AP ?

A5: Switch FAT and FIT mode by clicking the button at right corner ,then device will

reboot .Afterrebooting,please clear cookie and then login .

NOTE:Once the device is switched to FAT AP mode ,FAC controller will not be able to

manage &control it .

Q6: AC device list can not get AP devices ?

A6: The mode for AC controller and AP are different, AC controller with model prefixed

in AC is used to control FAT AP, the model prefixed in FAC or BW is used to control FIT AP .

NOTE:All the AP support both FAT and FIT AP mode ,the default mode is FIT AP mode .

Input password

Home

Wizard

WIFI

Network

Manage

Flow(2G Wifi)bps

Home

Wizard

WIFI

Network

Manage

AP Down Stream

AP Up Stream

Flow(2G Wifi) bps

Home

Wizard

WIFI

Network

Manage

Home

Wizard

WIFI

Network

Manage

Gateway Repeater Mode WISP Mode

Current Mode

AP Mode

Summary of content (2 pages)

PAGE 1
折位线折位线 1/Product introduction 折位线 2/Device installation 折位线 3/Device connection 5.In AP setup page,choose “Get IP from AC” in connection type,choose next step. AP Mode LED indicator instructions Bypass mode topology Cloud Server INTERNET 1 √ 2 LAN Settings IP Mode Get IP From AC Static IP One LED Indicator Name Normal Status System Light/WIFI Thress LED Indicator Ceiling Mount AP User Manual Name 2.
PAGE 2
FCC Warnning: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.