User Guide 1125 Matrix Printer
Tally Dascom 1125 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. • Never carry out maintenance or repair work yourself. Always contact a qualified service technician. • Keep this Operator’s Manual in a place which is easily accessible at all times. • Place the printer on a solid and even base so that it cannot fall. • Never place the printer in the vicinity of inflammable gas or explosive substances.
Tally Dascom 1125 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor sie den Drucker in Betrieb nehmen. x Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie immer einen qualifizierten Servicetechniker. x Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf. x Den Drucker auf stabilem und ebenem Untergrund so aufstellen, dass er nicht zu Boden fallen kann.
Tally Dascom 1125 Consignes importantes de sécurité (French) Lire attentivement les instructions suivantes avant de mettre l’imprimante en service. x Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un dépanneur qualifié. x Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber. x Ne jamais placer l’imprimante à proximité de sources de gaz aisément inflammables ou de substances explosives.
Tally Dascom 1125 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. x Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile. x Collocare la stampante su una superficie stabile, per evitare che cada a terra.
Tally Dascom 1125 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico de servicio calificado. x Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento. x Ponga la impresora sobre un base estable de manera que no pueda caer al suelo.
Tally Dascom 1125 ɉɪɚɜɢɥɚ ɩɨ ɬɟɯɧɢɤɟ ɛɟɡɨɩɚɫɧɨɫɬɢ. (Russian) ɉɪɨɱɢɬɚɣɬɟ, ɩɨɠɚɥɭɣɫɬɚ, ɢɧɫɬɪɭɤɰɢɸ ɩɨ ɬɟɯɧɢɤɟ ɛɟɡɨɩɚɫɧɨɫɬɢ ɩɟɪɟɞ ɜɤɥɸɱɟɧɢɟɦ ɜ ɪɚɛɨɬɭ ɩɪɢɧɬɟɪɚ. x ɇɟ ɜɵɩɨɥɧɹɣɬɟ ɬɟɯɧɢɱɟɫɤɢɟ ɪɚɛɨɬɵ ɢ ɪɟɦɨɧɬ ɬɟɯɧɢɤɢ ɫɚɦɨɫɬɨɹɬɟɥɶɧɨ, ɧɨ ɫɨɨɛɳɚɣɬɟ ɨ ɧɟɢɫɩɪɚɜɧɨɫɬɹɯ ɤɜɚɥɢɮɢɰɢɪɨɜɚɧɧɵɦ ɫɟɪɜɢɫɧɵɦ ɬɟɯɧɢɤɚɦ. x Ⱦɚɧɧɚɹ ɢɧɫɬɪɭɤɰɢɹ ɞɨɥɠɧɚ ɛɵɬɶ ɜɫɟɝɞɚ ɞɨɫɬɭɩɧɚ ɤɚɠɞɨɦɭ ɩɨɥɶɡɨɜɚɬɟɥɸ. x ɍɫɬɚɧɨɜɢɬɟ ɩɪɢɧɬɟɪ ɧɚ ɪɨɜɧɨɦ ɢ ɫɬɚɛɢɥɶɧɨɦ ɦɟɫɬɟ ɬɚɤ, ɱɬɨɛɵ ɨɧ ɧɟ ɫɦɨɝ ɭɩɚɫɬɶ ɧɚ ɩɨɥ.
Tally Dascom 1125 Instruções Importantes sobre Segurança (Portuguese) Leia as instruções de segurança antes de usar a impressora. x Consulte sempre um técnico qualificado para executar uma reparação . x Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas. x Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias explosivas. x Assegure-se de conectar a impressora à tomada elétrica com a voltagem apro-priada.
Tally Dascom 1125 Önemli Güvenlik Talimatları (Turkish) Lütfen, yazıcıyı iúletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun. x Bakım ve tamir çalıúmalarını kesinlikle ve hiçbir surette kendi baúınıza yapmayın; her zaman kalifiye bir uzman servis-teknisyenine haber verin. x Yazıcıyı, üzerinden yere düúmesi mümkün olmayacak sabit ve düz bir zemine yerleútirin.
Tally Dascom 1125 TRADEMARK ACKNOWLEDGEMENTS “IBM” is a trademark of International Business Machines Corporation. “EPSON” is a trademark of Epson America Incorporated. “DEC” is a trademark of Digital Equipment Corporation. “Centronics” is a trademark of Centronics Data Computer Corporation. “DOS” is a trademark of Microsoft Corporation. “SAP” is a trademark of SAP AG.
Tally Dascom 1125 X
Tally Dascom 1125 TABLE OF CONTENTS 1 UNPACKING GUIDE ........................................................................................................................................ 1 PLACING THE PRINTER .......................................................................................................................................... 2 PRINTER COMPONENTS ........................................................................................................................................
Tally Dascom 1125 ERROR INDICATIONS ON LEDS ............................................................................................................................ 43 DIAGNOSTIC FUNCTIONS .................................................................................................................................... 44 FIRMWARE UPDATE ...........................................................................................................................................
Tally Dascom 1125 1 Unpacking Guide x Place your packaged printer on a solid base. x Make sure that the “Up” symbols point in the correct direction. x Open the packaging, lift the printer out of the cardboard box and remove the remaining packaging material. x Check the printer for any visible transport damage and missing items. If you find any transport damage or if any accessories are missing, please contact your dealer.
Tally Dascom 1125 Placing the Printer Place the printer on a solid, flat, stable surface; ensuring that the printer is positioned in such a way that it cannot move, and that there is easy access to the control panel and paper input devices. Also ensure that there is enough space for sufficient ventilation and for the printed output. When selecting the printer location, observe the following additional instructions: x Never place the printer near to any flammable gas or explosive substances.
Tally Dascom 1125 Component Gap Lever Function Controls printing impact or density. Adjusts the print gap lever according to the thickness of paper. Paper Guides Adjusts positioning of single sheet paper. Print Head 24-pin printing mechanism Top Cover Protects print head and other components inside, and reduce noise. Control Panel Shows printer status, for printer setup.
Tally Dascom 1125 2 Setting Up Printer Install Ribbon 1. Ensure the power to the printer is off and the print gap lever “A” is set to the furthest open position. Move the carriage to the centre of the print platen. 2. Install the recess positions c on the ribbon cassette into the printer mounting. 3. Press the ribbon frame d onto the print head. 4. Turn the ribbon knob e in clockwise direction until the ribbon fabric is taut.
Tally Dascom 1125 Install the Single Sheet Feeder Install the single sheet feeder into the rear of the printer. Connecting the Interface Cable The 36-pin Centronics parallel, 25-pin serial RS-232C and USB ports are located at the rear of the printer. IMPORTANT: Make sure the printer and the computer are switched off before connecting or disconnecting the interface cable to prevent electrical damage to the interface ports.
Tally Dascom 1125 Connecting the Mains Power Checking the printer voltage Make sure that the device has been set according to your country’s power supply voltage. To do this, check the rating plate at the back of the printer. Contact your dealer if the setting is incorrect. Never switch on the printer if the voltage setting is incorrect; this may result in electrical damage to the printer. Make sure that the power switch “A”, located to the right side of the printer, is in the “O” (off) position.
Tally Dascom 1125 Installing the Windows Driver (Windows 2000/2003/2008 Server/XP/Vista/7) 1. Your printer CDROM comes with Windows drivers. Go to the Drivers folder and run the Installer “DriverSetup.exe”. You will see the screen on the right. Click “Next” to continue. 2. A list of ports available on your system will be displayed as shown on the right. Choose the desired port to use. Click “Next” to continue. 3. Select the desired printer model as shown on the right. Click “Next” to continue.
Tally Dascom 1125 4. Here you can choose whether to set the driver as the system default driver, and whether you want to print the Test Page after installation is completed. If the driver had been installed before, it would be listed in the white box on the right. Select the listed driver (if any) if you want to replace it; otherwise a copy of the driver will be installed. Click “Next” to continue. 5. Click “Finish” to start the installation process. 6.
Tally Dascom 1125 7. Installation in progress. 8. After installation is completed successfully, you will see the message on the right.
Tally Dascom 1125 3 Paper Installation Guide The printer can handle either single sheets or continuous forms. Single sheets, also called cut sheets, include envelopes and non-continuous, multipart forms. Continuous forms include labels and multipart forms fed into the printer using the forms tractors. The printer is able to print 1~5 plies multipart paper. Do not load paper that has been folded or is damaged, wrinkled, or curled.
Tally Dascom 1125 There are 2 paper feed modes: friction feed and tractor feed. Friction Feed Handling 1. Move the paper-feed lever forward to “ ” for friction feed mode. 2. Adjust the print gap lever if necessary. 3. Raise the single sheet feeder until it locks into its mounting. Align the left paper guide with the mark on the left of the single sheet feeder. Adjust the right paper guide to the width of the paper used. 4. Insert a sheet of paper.
Tally Dascom 1125 Tractor Feed Handling 1. Move the paper-feed lever backward to “ ” for continuous paper position. 2. Adjust the print gap lever if necessary. 3. Raise the tractor doors and fit the first 3 paper holes onto the left tractor pins. Close the left tractor door. In the same way, install the paper on the right tractor. 4. Adjust the right tractor to the width of the paper until the paper is flat. Do not stretch the paper too taut.
Tally Dascom 1125 Continuous Paper Placement 1. Place the printer on a solid base. The minimum suitable height of the solid base is 75 cm. 2. Left and right positioning: The direction of continuous paper should be parallel with the paper guide. The tolerance should be less than 3 cm. 3. Front and back positioning: The distance between the rear of printer and the wall should be more than 60 cm. To avoid paper jam, the distance between the continuous paper and the edge of desk should be 10~15 cm.
Tally Dascom 1125 4 Control Panel Operation There are 4 switches S1~S4 and 4 LEDs L1~L4. The meaning and application of each switch and LED are described below. LED Indicators “Power/Paper Out” LED: On: Power on Flashing: Paper out Flashing + buzzer: Paper jam “Online” LED: On: The printer is in online state and ready to receive data from the computer. Off: The printer is in offline state and cannot receive data. Flashing: The printer is in setup state and cannot receive data.
Tally Dascom 1125 “LF/FF” Key: Pressing this key will feed paper one line forward. By holding down this key, the printer will initially feed a few lines, then perform a form feed (continuous paper mode) or eject the form (single sheet mode). In the setup state, this key performs a reverse micro feed. “Tear Off” Key: When online, this key will move any loaded continuous paper to the tear-off position. When in setup state, this key is used to select the desired font. Table 4.
Tally Dascom 1125 Panel Operation There are 3 states of operation: Online, Setup and Power On. In the Online state, the keys provide the following functions: Go to Tear Off position, Line Feed/Form feed, Load/Eject, clear buffer and switch to offline state for access to Setup state. In the Setup state, the keys provide font selection and micro feed functions. To enter the Power On state, the user holds down a key or a combination of keys while powering up the printer.
Tally Dascom 1125 Online State Function Name Switch LED Operation Function Description This is valid for tractor mode only. It feeds the form to the tear-off position. After tearing off the form, printing starts Tear Off {S1} L1, L2 flash on the next TOF by: x pressing S1 once, or x receiving print data from the host. LF {S2} - Feeds a line with every press of S2.
Tally Dascom 1125 Setup State Function Name Switch LED Operation Function Description Toggling to the Online state will cause the printer to go into a Online state {S4} L4 ready-to-print state. Any changes made in Setup state will be saved permanently. Lighting up L4 indicates the Online state. Micro Up {S3} - Feeds up in 1/360” steps until the release of S3. Micro Down {S2} - Feeds down in 1/360” steps until the release of S2. Font Select {S1} L1, L2 Refer to Table 4.1 for details.
Tally Dascom 1125 Power-On State Function Switch Name Operation Status Page / Self Test [S4] LED - Function Description Prints the printer settings and self-test pattern. Pressing S1 can change the font. Beeps once to indicate going into hex dump mode: x Prints data from host in hexadecimal representation. x Lights up L4. x Pressing S4 suspends the printing.
Tally Dascom 1125 x Flashing of L3. x Lights up L4.and L3. Adjust Physical Margins x Lights up L1 or L2 according to current fonts. [S3]+[S4] x Includes Adjust Fanfold Top Margin, Adjust Single Top Margin, Adjust Fanfold Left Margin, Adjust Single Left Margin and Adjust Tear-Off position L1, L2, Service Menu [S1]+[S2] L3, L4 x Flashing of L3. x Lights up L4.and L3. x Lights up L1 or L2 according to current fonts. x Functions are: Vertical Alignment, Change Pin, and Endless Self-Test.
Tally Dascom 1125 5 Printer Setting Changes To meet your own print requirements, the printer configurations may be changed as follows: Hold down the Tear Off key while powering on the printer, release the Tear Off key when the print head starts to move. The printer will print out the current settings and then enter Main Menu setup state. Follow the instructions printed on how to make setting changes. When a new setting is saved, it is retained after the printer has been powered off.
Tally Dascom 1125 HS-Draft On: Prints High Speed Draft On, Off when Draft font is selected. When printing 180x180 DPI Graphic Speed graphics: Normal – prints in Normal, Fast, Ultra 180x180 DPI, Fast – prints in 90x180 DPI, Ultra – prints in 60x180 DPI. IBM Set 1/2 Selects the IBM character Set 1, Set 2 set.
Tally Dascom 1125 30. Roman8 31. Coax/Twinax 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdo 46. Greek DEC 47. Greek ELOT 928 Character Table Character table type Graphic Table, Italic Table selection.
Tally Dascom 1125 Specifies the waiting time before feeding the page to tear-off position automatically. Manual: Auto Tear Manual, 0.5s, 1s, 2s, 3s, 4s, 5s Auto tear mode is off. View1s, View2s, View3s: View1s, View2s, View3s After printing is completed, the printer will feed the paper until the last printed line is at the tear-off position. (Applies to tractor mode only) Interface Setup Interface Valid Settings Setup Interface Function Auto, Parallel, USB, For multi-host connection.
Tally Dascom 1125 printing.
Tally Dascom 1125 Perforationssprung Ja, Nein Abreissen Manuell, 0.5s, 1s, 2s, 3s, 4s, 5s, view1s, view 2s, view 3s Schnittstellen Setup Valid Settings Schnittstelle Auto, Parallel, USB, Serial I-PRIME Ja, Nein Protokoll Xon/Xoff, DTR Datenlänge 8, 7 Stopp Bit 1, 2 Parity None, Odd, Even Baud Rate 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 Auto IF Delay 10s, 30s RAM Nutzung Ladbarer Font, Puffer CX Bid Ja, Nein Erweitertes Setup Valid Settings Auto Laden Manuell, 0.
Tally Dascom 1125 ɋɤɨɪɨɫɬɶ ɝɪɚɮɢɤɢ ɇɨɪɦɚɥɶɧɚɹ, Ȼɵɫɬɪɚɹ, Ɉɱɟɧɶ ɛɵɫɬɪɚɹ ɋɢɦɜɨɥɵ IBM 1/2 ɍɫɬ. 1, ɍɫɬ.
Tally Dascom 1125 Ʉɨɧɬɨɥɶ ɞɥɢɧɵ ɮɨɪɦɵ ɉɪɨɝɪɚɦɧɵɣ, ɂɝɧɨɪ. Ʉɨɧɬɪɨɥɶ ɡɧɚɤɨɜ/ɞɸɣɦ ɉɪɨɝɪɚɦɧɵɣ, ɂɝɧɨɪ. Ʉɨɧɬɪɨɥɶ ɲɪɢɮɬɚ ɉɪɨɝɪɚɦɧɵɣ, ɂɝɧɨɪ. Ʉɨɧɬɪɨɥɶ ɤɚɱɟɫɬɜɚ ɉɪɨɝɪɚɦɧɵɣ, ɂɝɧɨɪ. Ɂɜɭɤ Ⱦɚ, ɇɟɬ Italian (Italiano) Menu Sistema Valid Settings Emulazione ESC/P2, IBM 2390 Plus Auto CR (IBM) Si, No Auto LF Si, No Direz.
Tally Dascom 1125 Menù Interfacc. Valid Settings Interfaccia Auto, Parallela, USB, Seriale I-PRIME Si, No Protocollo Xon/Xoff, DTR Lunghezza dati 8, 7 Stop Bit 1, 2 Parità No, Dispari, Pari Velocità 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 Ritardo Auto IF 10s, 30s Uso RAM Fonti utente, Memoria CX Bid Si, No Menù Avanzato Valid Settings Autocaricamento Manuale, 0.5s, 1s, 1.5s, 2s Previene Inceppamento Si, No Rileva Fine Carta Si, No Control. Lungh.
Tally Dascom 1125 Espagne, Japon, Norvège, Denmark II, Espagne II, Amerique latine, Korea, Legal Jeu de caractèr. CP 437, CP 857… Tabl.de caract. Graphque, Italique Setup page Valid Settings Lignes par pouce 1, 2, 3, 4, 5, 6, 7, 8 Papier continu Longueur formulaire 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Papier continu Bord supérieure 0/60" … 10/60"…99/60" Papier continu Bord inférieure 0/60"…10/60"...30/60" Feuille à feuille Longueur formulaire 3", 3.
Tally Dascom 1125 Spanish (Español) System Setup Valid Settings Emulación ESC/P2, IBM 2390 Plus Auto CR(IBM) Si, No Auto LF Si, No ModoImpresión Bi-Dir, Uni-Dir, Auto ModoImp.Borde Bi-Dir, Uni-Dir Impacto Normal, Fuerte IBM AGM Si, No Print Setup Valid Settings Fuente (Otros) OCR-B,OCR-A,ORATOR,GOTHIC,SOUVENIR Tamaño Letra 10cpp, 12cpp, 15cpp, 17cpp, 20cpp, PS Cero 0,Ø Alta Velocidad Activado, Desactivado Imp.
Tally Dascom 1125 Protocolo Xon/Xoff, DTR LongitudDatos 8, 7 Bit Parada 1, 2 Paridad Ninguna, Impar, Par Tasa Baudios 9600, 19200, 38400, 300, 600, 1200, 2400, 4800 Auto retraso 10s, 30s Uso de RAM Font Usuario, Buffer CX Bid Si, No Advanced Setup Valid Settings Auto Carga Manual, 0.5s, 1s, 1.
Tally Dascom 1125 Karakter Tablosu Grafik Tablosu, òtalik Sayfa Düzeni Ayarı Valid Settings ònç baġına satır 1, 2, 3, 4, 5, 6, 7, 8 Sürekli-kaáıt Form Uzunluáu 3",3.5",11/3", 4", 5", 5.5" 6",7",8", 8.5",11", 70/6", 12", 14", 17" Sürekli-kaáıt Üst kenar boġluáu 0/60" … 10/60"…99/60" Sürekli-kaáıt Alt kenar boġluáu 0/60"…10/60"...30/60" Tek-kaáıt Form uzunluáu 3", 3.5", 11/3", 4", 5", 5.5", 6", 7", 8", 8.
Tally Dascom 1125 Vertical Alignment The vertical alignment function is used to resolve any vertical line misalignments in bi-directional printing. Adjust Vertical Alignment Procedure: 1. Enter the Service Menu by holding down theɋTear/OffɌandɋLF/FFɌkeys while powering up. 2. Load paper. 3. The printer will print as follows: Service Menu ɋLF/FFɌ= OK ɋTear/OffɌ= Back ɋLoad/EjectɌ= Next ɋOnlineɌ= Exit Current SettingφVertical Alignment 4. PressɋLF/FFɌkey to select the current setting.
Tally Dascom 1125 printed above. 7. Once the setting which gives the best alignment is found, press ɋOnlineɌ key to exit current level. Printer will print “Save settings? Yes”. Press ɋLF/FFɌ key to save setting. Press ǏOnlineǐ key a few times until the printer exits the Service Menu. Change Pin Function When printer has been used for a long time or the print volume is high, the frequently used print head pins may fail.
Tally Dascom 1125 Adjust Physical Margins Adjust Page Margins allows for adjustments of physical left, top margins and tear-off position. Warning: Once these settings are changed, resetting the printer to factory defaults will not initialize these settings back to the original settings; so it is not advisable to perform this adjustment unless it is absolutely necessary. Adjust Top Margin Procedure: 1.
Tally Dascom 1125 Function of keys: ǏTear Offǐkey: Decrease 0.5mm ǏLoad/Ejectǐkey: Increase 0.5mm 5. Press ǏLF/FFǐ key, printer will print “Save settings˛Yes”. Press ǏLoad/Ejectǐ key to choose Yes or Noˈthen press ǏLF/FFǐ key to confirm selection and exit “Adjust Page Margins” mode by pressing ǏOnlineǐ. The print head moves to the left side and the printer beeps twice, then the print head moves to the middle position. Adjust Tear-Off Position Procedure: 1.
Tally Dascom 1125 Dascom Printer Setup Tool In the CDROM is a software utility called “Dascom Printer Setup”. This application enables a convenient, simple and fast way to control your printer without touching any keys on the operation panel. 1. Start the tool installation by double clicking the “Dascom Printer Setup.exe”. 2. Connect the printer to the system using USB cable 3. Power up the printer. 4. Load paper into the printer.
Tally Dascom 1125 6 Maintenance Your printer requires very little care. Occasional cleaning and replacement of the ribbon cartridge are all that is required. Cleaning is recommended approximately every 6 months or 300 hours of operation, whichever is sooner. Lubrication of the printer is not usually necessary. If the print head carriage does not move smoothly back and forth, clean the printer in the manner described in this chapter.
Tally Dascom 1125 4. To dry the platen, place a dry cloth against the platen and the rollers and manually rotate the paper feed knob.
Tally Dascom 1125 7 Troubleshooting Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, contact your dealer or service partner for assistance. Print Quality Problems and Solutions Problem Solution • Make sure that the ribbon cartridge is properly installed and that the ribbon feeds smoothly.
Tally Dascom 1125 Paper Handling Problems and Solutions Problem Solution • Make sure that the paper select lever located on the top right of Paper cannot be loaded or fed. the printer is set correctly. Move the lever to the front for single sheets or to the rear for continuous forms. • Make sure that the paper covers the paper-out sensor. • Turn off the printer and remove the jammed paper. Remove any obstructions from the paper path.
Tally Dascom 1125 • Make sure that the Online indicator is lit. • If you use the interface cable, make sure it is securely connected to both the printer and the computer. The printer is on but it will not print. • Make sure paper is loaded. • Run the printer Status Page. If printing executes normally, the problem is caused by: the interface, the computer, incorrect printer settings, or incorrect software settings.
Tally Dascom 1125 Diagnostic Functions The printer diagnostic functions are Self-Test page, hex-dump mode and print alignment adjustment. x Self-Test page: Tells you whether the printer hardware is functioning correctly. If the printer hardware is functional, any problems you are having are probably caused by incorrect printer settings, incorrect software settings, the interface, or the computer.
Tally Dascom 1125 Firmware Update Sometimes it is necessary update the firmware to solve a problem. The latest firmware file may be obtained from your dealer or downloaded from our website www.dascom.com. Before upgrading firmware, it is strongly recommended to print the Main Menu page to keep a record of the old settings. Note: Firmware update should only be performed by an authorized service person. We disclaim any responsibility for any damage caused if it is performed by any other person.
Tally Dascom 1125 8 General Specifications Print System Mono-chrome serial impact dot matrix Print Technology Uni-/bi-directional logic seeking for text and graphics Print Speed Font Matrix Print Head Graphics Pitch HS Draft Draft LQ 10 CPI 375/80H 250/120H 83/360H 12 CPI 300/120H 300/120H 100/360H 15 CPI 375/120H 375/120H 125/360H 17.
Tally Dascom 1125 Bitmap Fonts: 1. Draft 10, 12, 15, 17, 20 CPI 2. Roman 10, 12, 15, 17, 20 CPI, Proportional 3. Sans Serif 10, 12, 15, 17, 20 CPI, Proportional 4. Courier 10, 12, 15, 17, 20 CPI, Proportional 5. Prestige 10, 12, 15, 17, 20 CPI Built-In Fonts 6. OCR-B 10, 12, 17, 20 CPI 7. OCR-A 10, 12, 17, 20 CPI 8. Orator 10, 12, 15, 17, 20 CPI, Proportional 9. SOUVENIR 10, 12, 15, 17, 20 CPI, Proportional 10. GOTHIC 10, 12, 15, 17, 20 CPI, Proportional 11. Script 10, 12, 15, 17, 20 CPI 1. EAN-13 2.
Tally Dascom 1125 21. 8859-1 22. 8859-1 (SAP) 23. 8859-2 24. 8859-5 25. 8859-7 26. 8859-9 27. 8859-15 28. BRASCII 29. Abicomp 30. Roman8 Code Pages 31. Coax/Twinax 32. New-437 33. New-Dig 850 34. Old-Code 860 35. Flarro 863 36. 865 Hebrew 37. CP 1257 38. 866 Ukraine 39. 866 Kazakhstan 40. Kamenicky 41. Mazovia 42. CP 775 43. CRO-ASCII 44. Arabic Farsi 45. Arabic Urdo 46. Greek DEC 47. Greek ELOT 928 1. USA 2. France 3. Germany 4. UK 5. Denmark I 6. Sweden 7. Italy International Character Sets 8.
Tally Dascom 1125 Line Spacing 1/6", 1/8", n/60", n/180", n/360" Fanfold Paper Cut Sheet Paper Specifications Single ply Multi-part Width: 76.2mm̚256.5mm Width: 76.2mm̚254mm (3"̚10"˅ ˄3"̚10.1"˅ Length: Length: 101.6mm min (4" min) 101.6mm̚363.2mm ˄3.9"̚14.3"˅ Paper Specifications Weight: 52̚100g/ Weight: 52̚100 g/ Thickness: Thickness: 0.065̚0.14mm 0.065̚0.14mm (0.0026"̚0.0055”) (0.0026"̚0.
Tally Dascom 1125 Weight Power Supply 5 kg Unit type: Switching mode power supply Power cord: Detachable Voltage rating: AC 230V (180V~264V), 50Hz to 60Hz AC 110V/120V, 60Hz (factory option) Stand by: Less than 3.8W ESD: Comply with IEC801-2 Contact discharge: 4kV Air discharge: Power consumption MTTR MTBF Certification 8kV 28.
Tally Dascom 1125 9 Interfaces Parallel Interface Parallel Interface Pin Assignment Pin Signal Name Signal Transmission 1 STROBE ¯¯¯¯¯¯ Printer I Computer 2~9 DATA Printer I Computer 10 ACK ¯¯¯ Printer J Computer 11 BUSY Printer J Computer 12 PE Printer J Computer 13 SELECT Printer J Computer 14 AFXT ¯¯¯¯ Printer I Computer 15 Unused Unused 16 GND Printer Q Computer 17 F-GND Printer Q Computer 18 +5V Printer J Computer 19~30 GND Printer Q Computer 31 INIT ¯¯¯¯ Print
Tally Dascom 1125 USB Interface The USB interface conforms to the Universal Serial Bus 2.0 Specifications. It supports the Full Speed mode at 12 Mbps. It uses the “B” type USB connector.
Tally Dascom 1125 10 Character sets & Code Pages Character Sets Standard Character Set 1 Standard Character Set 2 53
Tally Dascom 1125 IBM Character Set 1 IBM Character Set 2 54
Tally Dascom 1125 International character sets International Character Set Commands Country USA Command ˘ESC˚“R”CHRˀ˄0˅ France ˘ESC˚“R”CHRˀ˄1˅ Germany ˘ESC˚“R”CHRˀ˄2˅ UK ˘ESC˚“R”CHRˀ˄3˅ Denmark1 ˘ESC˚“R”CHRˀ˄4˅ Sweden ˘ESC˚“R”CHRˀ˄5˅ Italy ˘ESC˚“R”CHRˀ˄6˅ Spain1 ˘ESC˚“R”CHRˀ˄7˅ Japan ˘ESC˚“R”CHRˀ˄8˅ Norway ˘ESC˚“R”CHRˀ˄9˅ Denmark2 ˘ESC˚“R”CHRˀ˄10˅ Spain2 ˘ESC˚“R”CHRˀ˄11˅ Lat America ˘ESC˚“R”CHRˀ˄12˅ Korea ˘ESC˚“R”CHRˀ˄13˅ Legal ˘ESC˚“R”CHRˀ˄64˅ 55
Tally Dascom 1125 Character Tables Italic 56
Tally Dascom 1125 Graphic 1 Graphic 2 57
Tally Dascom 1125 Code Page Commands Code Page ESC R Parameter CRO-ASCII 3C Arabic Farsi 96 Arabic Urdo 97 Greek DEC 46 Greek ELOT 928 6C CP437 Latin US 80 CP737 Greek 93 CP850 Latin 1 82 CP851 Greek 88 CP852 Latin 2 87 CP857 Turkish 8D CP858 (IBM with €) 9E CP860 Portugal 84 CP861 Icelandic 94 CP863 French Canada 85 CP864 Arabic 8C CP864 Arab.
Tally Dascom 1125 Coax/Twinax(Hebrew) 4F New-437 (Hebrew) 81 New-DIG 850 (Hebr.) 83 Old-Code 860 (Hebr.
Tally Dascom 1125 Code Page Tables CP 437 (US) CP 737 Greek 60
Tally Dascom 1125 CP 850 (Multilingual) CP 851 61
Tally Dascom 1125 CP 852 (Eastern Europe) CP 857 (Turkish) 62
Tally Dascom 1125 CP 858 CP 860 (Portugal) 63
Tally Dascom 1125 CP 861 (Iceland) CP 863 (French-Canadian) 64
Tally Dascom 1125 CP 864 Arabic CP 864 Arabic Extended 65
Tally Dascom 1125 CP 865 (Norway) CP 866 (Cyrillic) 66
Tally Dascom 1125 CP 866 Bulgaria CP 1250 Win Latin 2 67
Tally Dascom 1125 CP 1251 Win Cyrillic CP 1252 Win Latin 1 68
Tally Dascom 1125 CP 1253 Win Greek CP 1254 Win Turkish 69
Tally Dascom 1125 8859-1 Latin 1 8859-1 Latin 1 (SAP) 70
Tally Dascom 1125 ISO 8859-2 (ISO Latin 2) ISO 8859-5 Cyrillic 71
Tally Dascom 1125 ISO 8859-7 (Latin/Greek) ISO 8859-9 (Turkish) 72
Tally Dascom 1125 ISO 8859-15 Euro (Code Page 923) BRASCII 73
Tally Dascom 1125 Abicomp Roman 8 74
Tally Dascom 1125 Coax/Twinax (Hebrew) New-437 (Hebrew) 75
Tally Dascom 1125 New-Dig 850 (Hebrew) Old-Code 860 (Hebrew) 76
Tally Dascom 1125 Flarro 863 (Hebrew) 865 Hebrew 77
Tally Dascom 1125 CP 1257 866 Ukraine 78
Tally Dascom 1125 866 Kazakhstan Kamenicky 79
Tally Dascom 1125 Mazovia CP 775 80
Tally Dascom 1125 CRO-ASCII Arabic Farsi 81
Tally Dascom 1125 Arabic Urdo Greek DEC 82
Tally Dascom 1125 Greek ELOT 928 83
Tally Dascom 1125 11 Control Codes Summary Epson Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN DEL ESC SO ESC SI ESC SP n ESC EM n ESC ! n ESC ( - n1 n2 m d1 d2 ESC $ n1 n2 ESC | n ESC % n ESC & ESC ( ^ n m d1 d2… ESC (G NUL d ESC * m n1 n2… ESC .
Tally Dascom 1125 ESC : ESC ˘ ESC > ESC = ESC # ESC ˛n m ESC @ ESC ˸n1 n2 ESC A n ESC B…NUL ESC C n ESC D…NUL ESC E ESC F ESC G ESC H ESC J n ESC K n1 n2 … ESC L n1 n2 … ESC M ESC N n ESC O ESC P ESC Q n ESC R n ESC S n ESC T ESC U n ESC ( V NUL n m ESC W n ESC X n1 n2 ESC Y n1 n2 … ESC Z n1 n2 … ESC a n ESC b n ESC c n m ESC g ESC j n ESC k n ESC p n ESC q n ESC r n ESC t n ESC (t nL nH d1 d2 d3 ESC ( v NUL n m ESC w n ESC x n ESC( B n1 n2 k m s v1 v2 c Copy ROM to RAM Unidirectional mode(1 line) Set MSB
Tally Dascom 1125 IBM Emulation Command List Command Sequence BEL BS HT LF VT FF CR SO SI DC1 DC2 DC3 DC4 CAN ESC BEL ESC BS ESC HT ESC CR ESC LF ESC SO ESC SI ESC DC1 ESC DC2 ESC DC3 ESC DC4 ESC CAN ESC FF ESC EM n ESC : ESC VT ESC 0 ESC 1 ESC 2 ESC 3 n ESC 4 ESC 5 n ESC 6 ESC 7 ESC = ESC \ ESC ^ ESC A n ESC B n ESC C n Function Beeper Backspace Tab horizontally Line feed Tab vertically Form feed Enter Select double-wide mode Select condensed mode Online Select 10CPI Offline Cancel double-wide mode(one l
Tally Dascom 1125 ESC C NUL n ESC D ESC E ESC F ESC G ESC H ESC I n ESC J n ESC K n1 n2 V1 V2 …Vn ESC L n1 n2 V1 V2 …Vn ESC N n ESC O ESC P n ESC Q n ESC R ESC S n ESC T ESC U n ESC W n ESC X n m ESC Y n1 n2 V1 V2 …Vn ESC Z n1 n2 V1 V2 …Vn ESC [- n1 n2 m1 m2 ESC [@ n1 n2 m1 m2 m3 m4 ESC [I n1 n2 Hf Ls Hs Lf Sm NUL Hc Lc ESC [ K n1 n2 init id para1 para2 …paran ESC [ T n1 n2 n3 n4 Hc Lc ESC [\ ESC [d ESC [f n1 n2 k m s v1 v2c ESC [g n1 n2 m ESC [p n1 n2 ESC ] ESC_ n ESC- n ESC d n m ESC j ESC r n ESC * m S
Tally Dascom 1125 FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: a. This device may not cause harmful interference. b. This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
DASCOM REPRESENTATIVES GERMANY UNITED KINGDOM RUSSIA and CIS DASCOM Europe GmbH DASCOM GB Ltd DASCOM Europe GmbH Heuweg 3 ViewPoint, Basing View, Representation Moscow D-89079 Ulm Basingstoke, Hampshire Leninsky Prospekt 95a, Office 322 Deutschland RG21 4RG, England 119313 Moscow, Russian Federation Tel.: +49 (0) 731 2075 0 Phone: +44 (0) 1256 481481 Phone: +7 (495) 984 70 65 Fax: +49 (0) 731 2075 100 Fax: +44 (0) 1256 481400 Fax: +7 (495) 984 56 42 www.dascom.com www.dascom.com www.
