User Manual DL-210 Label & Barcode Printer
Tally Dascom DL-210 User Guide V1.3 Important Safety Instructions (English) Read the following instructions thoroughly before starting up your printer. • The device and mains-socket must all times be easily accessible. • Never carry out maintenance or repair work yourself. Always contact a qualified service technician. • Keep this user guide in a place which is easily accessible at all times. • Place the printer on a solid and even base so that it cannot fall.
Tally Dascom DL-210 User Guide V1.3 Wichtige Sicherheitshinweise (German) Lesen Sie bitte diese Sicherheitshinweise durch, bevor Sie den Drucker in Betrieb nehmen. Das Gerät und die Netzsteckdose müssen jeder Zeit leicht zugänglich sein. Führen Sie Wartungsarbeiten und Reparaturen keinesfalls selbst aus, sondern verständigen Sie immer einen qualifizierten Servicetechniker. Bewahren Sie diese Dokumentation an einem jederzeit zugänglichen Ort auf.
Tally Dascom DL-210 User Guide V1.3 Consignes importantes de sécurité (French) Lire attentivement les instructions suivantes avant de mettre l’imprimante en service. Le dispositif et la prise principale doivent toujours être accessibles facilement. Ne jamais effectuer soi-même les travaux d’entretien et de réparations. Contacter toujours un dépanneur qualifié. Placer l’imprimante sur un support stable de façon à ce qu’elle ne puisse pas tomber.
Tally Dascom DL-210 User Guide V1.3 Indicazioni di sicurezza importanti (Italian) Prima di mettere in funzione la stampante, leggere attentamente le seguenti indicazioni. Il dispositivo e la presa di corrente devono essere sempre facilmente accessibili. Non eseguire mai da sé gli interventi di manutenzione e riparazione, ma rivolgersi sempre a un tecnico di assistenza qualificato. Conservare le presenti istruzioni per l’uso in un luogo sempre accessibile.
Tally Dascom DL-210 User Guide V1.3 Instrucciones de seguridad importantes (Spanish) Lea las siguientes instrucciones con esmero antes de poner la impresora en servicio. El dispositivo y la toma de corriente deben estar ubicados de forma que sea fácil acceder a ellos. Nunca lleve a cabo trabajos de mantenimiento o reparación Ud. mismo, sino consulte a un técnico de servicio calificado. Guarde las presentes instrucciones de servicio en un lugar de fácil acceso en cualquier momento.
Tally Dascom DL-210 User Guide V1.3 Правила по технике безопасности. (Russian) Прочитайте, пожалуйста, инструкцию по технике безопасности перед включением в работу принтера. Устройство и розетка должны быть всегда легко доступна. Не выполняйте технические работы и ремонт техники самостоятельно, но сообщайте о неисправностях квалифицированным сервисным техникам. Данная инструкция должна быть всегда доступна каждому пользователю.
Tally Dascom DL-210 User Guide V1.3 Instruções Importantes sobre Segurança (Portuguese) Leia as instruções de segurança antes de usar a impressora. A impressora e a tomada devem ser facilmente em todos os momentos acessíveis. Consulte sempre um técnico qualificado para executar uma reparação . Coloque a impressora sobre uma base sólida e nivelada, para que ela não sofra quedas. Jamais instale a impressora nas proximidades de lugares onde haja gás inflamável ou substâncias explosivas.
Tally Dascom DL-210 User Guide V1.3 Önemli Güvenlik Talimatları (Turkish) Lütfen, yazıcıyı işletime geçirmeden önce bu güvenlik talimatlarını bütünüyle dikkatle okuyun. Cihaz ve elektrik prizinin her zaman kolayca erişilebilir olması gerekir. Bakım ve tamir çalışmalarını kesinlikle ve hiçbir surette kendi başınıza yapmayın; her zaman kalifiye bir uzman servis-teknisyenine haber verin. Yazıcıyı, üzerinden yere düşmesi mümkün olmayacak sabit ve düz bir zemine yerleştirin.
Tally Dascom DL-210 User Guide V1.3 TRADEMARK ACKNOWLEDGEMENTS “IBM” is a trademark of International Business Machines Corporation. “EPSON” is a trademark of Epson America I ncorporated. “DEC” is a trademark of Digital Equipment Corporation. “Centronics” is a trademark of Centronics Data Computer Corporation. “DOS” is a trademark of Microsoft Corporation. “SAP” is a trademark of SAP AG.
Tally Dascom DL-210 User Guide V1.3 About This Manual This manual provides information to operators of the DL-210 to describe basic operations to enable safe and correct use of the printer. Symbols Description The symbols in this manual are identified by their level of importance, as defined below. Read the following carefully before handling the product. CAUTION: Provides information that must be observed to prevent damage to the equipment or loss of date.
Tally Dascom DL-210 User Guide V1.3 TABLE OF CONTENTS About This Manual .................................................................................................................... X 1 INTRODUCTION ...................................................................................................................... 1 1.1 Features...................................................................................................................................... 1 1.2 Printer specification ........
Tally Dascom DL-210 User Guide V1.3 5.2 Resetting the Factory Default Values ........................................................................................... 47 5.3 Removing Jammed Label .............................................................................................................. 47 5.4 Cleaning Thermal Print Head ........................................................................................................ 48 5.5 Maintenance...........................................
Tally Dascom DL-210 User Guide V1.3 1 INTRODUCTION The Dascom® DL-210 model is the best value in a desktop thermal printer. The DL-210 printer provides thermal transfer and direct thermal printing at speeds up to 6 ips (inches per second) at a 203 dpi (dots per inch) print density. 1.1 Features • Easy to switch printer language between ZPL, EPL and TSC programming and label formats. • Easy operation. With open structure users can easily change paper roll and ribbon. • Large media compartment.
Tally Dascom DL-210 1.2 User Guide V1.3 Printer specification Print Parameter Print method Print width Print speed Print head Resolution Chinese Alphanumeric User-defined Fonts Code Pages Scalable/Rotation Graphics 1D Direct thermal/Thermal transfer printing 108mm 6IPS Dot pitch: 0.
Tally Dascom DL-210 Power Supply Memory Interface Input Output SDRAM FLASH Standard Optional Software Physical Spec. Safety Standard Dimensions Casing Color Weight Operating condition Storage condition Safety EMC Certificate Optional kit Reliability 1.3 TPH lifetime User Guide V1.3 External power adapter AC 100V-240V, 50-60Hz 24V DC, 3A 8MB 8MB USB (2.
Tally Dascom DL-210 Media Type Non-Continuous Roll Media How it looks User Guide V1.3 Description Roll media is wound on a core that can be 0.5 to 1.5 in. (12.7 to 38.1 mm) in diameter. Labels have adhesive backing that sticks them to a liner, and they are separated by gaps, holes, notches, or black marks. Tags are separated by perforations. Individual labels are separated by one or more of the following methods: • Web media separates labels by gaps, holes, or notches.
Tally Dascom DL-210 1.4 User Guide V1.3 External Dimension and Mass Width: Approximately 230 mm Depth: Approximately 290 mm Height: Approximately 179.5 mm Mass: Approx.
Tally Dascom DL-210 1.5 User Guide V1.3 Unpacking When you receive the printer, please check for possible shipping damage: 1. Inspect the outside of both the box and the printer for possible damage. 2. Open the top cover of the printer to see if the media compartments are in order. If you discover shipping damage upon inspection: Immediately notify the shipping company and file a damage report. Keep all packaging material for shipping company inspection.
Tally Dascom DL-210 User Guide V1.
Tally Dascom DL-210 1.6 User Guide V1.3 Product Configuration Interface Types Optional Interface (Serial/ Parallel/ Ethernet/ Bluetooth） USB interface USB interface (USB2.0, Full speed) Serial interface: Serial port (RS-232, DB25) Parallel interface: Bidirectional parallel port (IEEE1284) LAN interface: Ethernet (10Base-T, 100Base-TX) Bluetooth interface (BT 2.
Tally Dascom DL-210 1.7 User Guide V1.
Tally Dascom DL-210 User Guide V1.3 Ribbon Pick-up Holder Print Head Mechanism Ribbon Holder Media Holder Print Head Locking Button Print Head Locking Button Print Head Ribbon Pick-up Holder Tear Bar Rotatable Board Component Name Print Head Ribbon Holder Mechanism Print Head Ribbon Pick-up Holder Media Holder Print Head Locking Button Function For placing ribbon, lower seat for new ribbon, top seat for used ribbon.
Tally Dascom DL-210 User Guide V1.3 Media Guide Media Guide Adjuster Black Mark Sensor Platen Roller Component Name Media Guide Media Guide Adjustor Black Mark Sensor Platen Roller Function Align the media in the center of media path Adjust the space between the two media guides For detecting black mark. The sensor position can be adjusted according to the black mark position.
Tally Dascom DL-210 1.8 User Guide V1.3 Control Panel 1.8.1 LEDs Behavior LEDs Power Status LEDs’ behavior Status On ○ Power on. Off ● Error or power off. On ○ Paper end. Off ● Normal. Fast blink Error ○●○●○●○ Label remains in peeler. Slow blink ○●●○●●○ Ribbon end. On ○ Print head mechanism is opened. Off ● Normal. Fast blink ○●○●○●○ Print head is over-heated. 1.8.
Tally Dascom DL-210 User Guide V1.3 2 SETUP 1.1 Flow of Setup This chapter consists of the following sections along with the setup flow of the product and peripherals. 1. Placing the Printer (page 13) 2. Adjusting Sensor (page 15) 3. Loading Paper Roll (page 16) (page 4. Loading Ribbon (optional) (page 18) (page 5. Attaching Power (page 14) 6. Printing Self-test (page 42) 7. Connecting the Printer to the Host Computer (page 23) 2.1 Placing the Printer You can install this printer horizontally.
Tally Dascom DL-210 User Guide V1.3 2.2 Attaching Power Checking the voltage of the power adapter Before you connect the power adapter to the power socket check if the voltage is correct. If you connect the power adapter to power with incorrect voltage this may result in electrical damage to adapter and printer. 1. Make sure the printer and the computer are powered off. 2. Connect the power cord to the power adapter. 3. Connect the power adapter to the power supply interface at the rear of the printer.
Tally Dascom DL-210 User Guide V1.3 2.3 Calibrate Sensor Gap sensor and reflective sensor should be calibrated separately. First of all, please open the setup tool, enter “Printer Setup”, choose paper sensor: gap sensor by default. You could switch to reflective sensor according to your need. 2.3.1 Calibrate Gap Sensor (1) Make sure gap sensor is selected through the setup tool. (2) Lift the top cover to expose the media holder and the print head mechanism.
Tally Dascom DL-210 User Guide V1.3 Label Black Mark Sign liner Lower Sensor (4) Put the media between the media compartment and the tear bar. And then close the mechanism and the top cover. 2.4 Loading Roll Media Must use thermal media in case of no ribbon in the printer. If using ribbon, you have to use thermal transfer media. Tips for avoiding media jam: Make sure the media is aligned in the center of the printer and the media fixers are firmly pressed against both sides of the roll.
Tally Dascom DL-210 User Guide V1.3 (5) Unlatch the print head mechanism by pushing the two blue locking buttons on the sides toward the rear. (6) Lead the media under the print head mechanism through the media guides. (7) Control the blue media guide adjustor so as to align the media in the central path. (8) Lead the media over the platen roller and through the tear bar. (9) Put the print head mechanism down and press down firmly until you hear a snap.
Tally Dascom DL-210 User Guide V1.3 2.5 Loading Transfer Ribbon Transfer ribbons come in several varieties and in some cases colors to match your application needs. The media and ribbon types should be matched to provide you with optimal print results. Always use ribbon that is wider than the media to protect the printhead from wear. For direct thermal printing, do not load ribbon in the printer. Do not use ribbon while using direct thermal media. Otherwise, barcode and graph will be distorted.
Tally Dascom DL-210 User Guide V1.3 (6) Open the sensor support. (7) Insert the ribbon roll into the ribbon holder (lower seat of the print head mechanism): Insert the hexagon end onto the ribbon adjustor (blue gear), then insert the other end into the slot of the ribbon holder.
Tally Dascom DL-210 User Guide V1.3 (9) Turn the wheel of the print head mechanism to ensure the ribbon is tightly wound. (10) Close the sensor support. (11) Press down the print head mechanism on both sides firmly until you hear a snap.
Tally Dascom DL-210 User Guide V1.3 2.6 Connecting to Computer NOTE! Be sure to install the driver before connecting the printer to the host computer. Before installing, disconnect the Power Unit from the printer (as well as turning the power switch off). Even when the power switch is off, voltage is still present at some points on the circuit board. Changing components while the power unit is connected can cause damage to the interface board and the printer.
Tally Dascom DL-210 User Guide V1.3 2.7.1 Connecting USB interface CAUTION! Be careful not to insert the USB interface cable into the cash drawer kick-out connector. 2.7.2 Connecting serial interface WARNING! Be sure to turn off the power supply for both the printer and host computer before connecting the cables. 1. Insert the interface cable connector firmly into the interface connector on the connector panel. 2.
Tally Dascom DL-210 User Guide V1.3 3. When using interface cables equipped with a grounding line, attach the ground line to the screw hole marked “FG” on the printer. 4. Connect the other end of the interface cable to the host computer. 2.7.3 Connecting parallel interface 1. Insert the interface cable connector firmly into the interface connector on the connector panel. 2. Press down the clips on either side of the connector to lock it in place. 3.
Tally Dascom DL-210 User Guide V1.3 Before installation, make you have installed the driver and the driver for Ethernet interface (see Installing Driver on page 17) When LAN cables are installed outdoors, make sure devices without proper surge protection are cushioned by being connected through devices that do have surge protection. Otherwise, the devices can be damaged by lightning.
Tally Dascom DL-210 User Guide V1.3 3 NETWORK SETUP AND CONFIGURATION 3.1 Installing Driver Switch off the printer before running the printer driver setup. Your printer CD-ROM comes with Windows Driver. Go to the Driver folder and run the installer. Please check the website www.dascom.com for the latest version of driver. (1) Click “Next”.
Tally Dascom DL-210 User Guide V1.3 (3) Select the installation path to the Driver. (3) Click “Finish”.
Tally Dascom DL-210 User Guide V1.3 (4) Click “Yes”. (5) Click “Next”.
Tally Dascom DL-210 User Guide V1.3 (6) Choose interface. (7) Choose printer model “Tally Dascom DL-210Z” or “Tally Dascom DL-210E”, and the installation path. Then click “Next”.
Tally Dascom DL-210 User Guide V1.3 (8) Click “Next”. (9) Enter printer name. Click “Next”.
Tally Dascom DL-210 User Guide V1.3 (10) Click “Finish”. (11)Then the driver is installed successfully.
Tally Dascom DL-210 User Guide V1.3 3.2 Installing Setup Tool Your printer CD-ROM comes with Tally Dascom Setup Tool. Go to the folder and run the installer. Please check the website www.dascom.com for the latest version of setup tool. (1) Choose setup language. (2) Click next.
Tally Dascom DL-210 User Guide V1.3 (3) Select the installation path to the tool. (4) Click “Finish”.
Tally Dascom DL-210 User Guide V1.3 (5) Click “Install”. (6) Click “Install”.
Tally Dascom DL-210 User Guide V1.3 (7) Installation complete. Click “Finish”.
Tally Dascom DL-210 User Guide V1.3 3.3 Setup Tool Application A CD comes along with printer. The CD contains POS & label printer setup tool for configuring printer. Or, please find the latest setup tool on Dascom website: www.dascom.com Read the help file carefully before using the setup tool. Please click “Help” button below for more information. 3.3.1 Model and Interface Setting Select the printer model and the suitable interface before configuring printer.
Tally Dascom DL-210 User Guide V1.3 3.3.2 Configuring Printer After model and interface setting, select “Printer Setup” tab for configurations. Setup Items Explanation Setup Items Options Default Page Mode On, Off On Print Density 1, 2, 3, 4, 5, 6 2 Print Media Label Paper, Continuous Paper Label Paper Printer Language English, Chinese English Print Method Thermal Transfer, Direct Thermal Thermal Transfer Set the printer’s system language, Chinese or English.
Tally Dascom DL-210 User Guide V1.3 Print Position Detection On, Off Off Auto Calibrate Label On, Off Off Top Form Sensing On. Off Off Paper Sensor Selection Gap sensor, Reference sensor Gap sensor Print Home Offset User-defined 0 Cutting position offset User-defined 0 Black mark AD value User-defined 0 Enable print position detection or not On: It will auto calibrate the label when you use a different size/format of label.
Tally Dascom DL-210 User Guide V1.3 3.4 LAN Interface Setup (1) Select Network interface in the setup tool. And then click “Setting”. (2) Click “Setup Printer”.
Tally Dascom DL-210 User Guide V1.3 (3) You could change DHCP, IP address or other settings. And then enter OK. (4) At the end, click OK to implement the change.
Tally Dascom DL-210 User Guide V1.3 3.6 Update Firmware Dascom is not liable if customers are doing a firmware update by themselves. If power is switched off during the process, the printer may be damaged afterwards. (1) Preparation USB cable, 24V power adapter, DL-210 setup tool, firmware file. (2) Connection Connect printer and host with USB cable firmly. Check the Device Manager, if connection is successful, “USB printing support” will display under “universal serial Bus Controllers” directory.
Tally Dascom DL-210 User Guide V1.3 ② Hold down Feed Key and switch on printer simultaneously. Release Feed Key once powering on, the printer will beep once. ③ Status LED on, printer enter upgrade mode. (4) Upgrade Firmware ① Run Dascom setup tool, select model Label Printer and USB interface. ② Select “Update Firmware” tab, then click “Browse” to locate the firmware/CG file, and then click “Update”. May take about 20 seconds. ③ After loading the firmware, the Power LED, Error LED and Status LED blink.
Tally Dascom DL-210 User Guide V1.3 4 SETTING/CHECKING MODES Besides the ordinary print mode, the printer has the following modes to set or to check settings of the printer. Self-test Mode Hexadecimal Dumping Mode 4.1 Print a Parameter Setting Page (Self-test Page) Before you connect the printer to the computer, make sure that the printer is in proper working order. You can do this by printing a configuration status label. 1.
Tally Dascom DL-210 User Guide V1.3 Here is the self-test status page and its explanation. The printout is an example. It may differ depending of installed options or interfaces: Parameter settings Model DL-210 SN NO XXXXXXXXXXXX ID NO 28.904.XX Firmware version...........................40.XX.XX Interface....................................USB+Parallel Serial interface…..9600bps 8bitD/1bits/None Emulation..............................................ZPLII Media............................................
Tally Dascom DL-210 User Guide V1.3 4.2 Hexadecimal Dumping Mode Hold down Feed Key and switch on printer till Power LED blinks three times, buzzer beeps three times. When self-test is OK but on-line printing error occurs, you can check the communication between PC and program via Hexadecimal Dump mode. In Hexadecimal Dump mode, the printer will print out hexadecimal data once it receives the signal from host. You can ask technical service for analysis.
Tally Dascom DL-210 User Guide V1.3 4.3 Auto Calibrate Label DL-210 can calibrate label automatically. Hold down Feed Key and switch on printer till Power LED blinks twice, buzzer beeps twice. Label calibration should be executed in the following situations: Use printer for printing label first time. Replace different size of labels. Printer skips labels Printer feeds blank labels. Refill with new roll of labels.
Tally Dascom DL-210 User Guide V1.3 5 TROUBLESHOOTING AND MAINTENANCE Your printer is extremely reliable, but occasionally problems may occur. This chapter provides information on some of the common problems you may encounter and how you may solve them. If you encounter problems that you cannot resolve, please contact your dealer for assistance. Read the following instructions before maintenance and avoid incorrect operation, so as to prevent injury to you and damage to the printer. 5.
Tally Dascom DL-210 User Guide V1.
Tally Dascom DL-210 User Guide V1.3 5.4 Cleaning Thermal Print Head After printing, the print head becomes very hot. Be careful not to touch it and to let it cool before you clean it. Do not damage the print head by touching it with your fingers or any hard object. Turn off the printer, open the top cover and remove ribbon, clean the thermal elements of the print head with a cotton swab moistened with alcohol solvent (ethanol, methanol, or isopropyl).
Tally Dascom DL-210 User Guide V1.3 6 COMMUNICATION INTERFACES SPECIFICATIONS 6.1 USB interface USB interface pin assignment PIN No. 1 2 3 4 Description VBUS DD+ GND Classic wire color Red White Green Black USB interface connector diagram 6.3 Bluetooth Interface Bluetooth version: Standard BT2.1+EDR Communication protocol: SPP Radio frequency: 2.4GHz Transmission distance: 10m 6.4 Ethernet interface Ethernet interface pin assignment Pin. No.
Tally Dascom DL-210 User Guide V1.3 Ethernet interface connector diagram 6.5 Serial interface Serial interface pin assignment Serial interface compatible with RS-232 standard, with 25 pin (D hole type) socket. PIN No. PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8~19 PIN 20 PIN 21~25 Description Frame Ground TXD RXD RTS Unconnected DSR Signal Ground Unconnected DTR Unconnected User can view the setting of interface via printing configuration sample.
Tally Dascom DL-210 User Guide V1.3 6.6 Parallel interface Parallel interface pin assignment Parallel interface with 36 pin CENTRONICS socket. Pin No. Signal From 1 H 2 3 4 5 6 7 8 9 H H H H H H H H 10 P 11 P 12 P 13 14 15 16 17 18 19~30 31 32 Description Strobe Signal; Data latch pulse, latch the data to the printer at the rising edge of the negative pulse.
Tally Dascom DL-210 User Guide V1.3 6.7 Power Supply (1) Power adapter Input: AC 100V-240V~ 1.5A 50-60Hz Output: DC 24V±5%, 2.1A, A-1009-3P interface (2) Power Supply connector diagram (3) Power Socket pin assignment Pin Number Signal Name 1 +24 V 2 GND 3 N.C SHELL F.G.
Tally Dascom DL-210 User Guide V1.3 7 CHARACTER CODE PAGES The character code tables show only character configurations. They do not show the actual print pattern. “SP” in the table shows a space. 7.1 Common to all pages (International Character Set: USA) HEX 0 0 1 NUL 2 DLE 00 16 XON 1 01 18 XOFF 3 03 6 EOT 04 ENQ A D E F 5 07 6 38 ‘ 23 08 39 24 40 09 25 41 * 10 26 ESC 11 FF FS CR 13 43 < 29 = 45 .
Tally Dascom DL-210 User Guide V1.3 7.2 International Character Sets ASCII code (Hex) Country 23 24 40 5B 5C 5D 5E 60 7B 7C 7D 7E USA # $ @ [ \ ] ^ ` { | } ~ France # $ à ° ç § ^ ` é ù è ¨ Germany # $ § Ä Ö Ü ^ ` ä ö ü β U.K. £ $ @ [ \ ] ^ ` { | } ~ Denmark I # $ @ Æ Ø Å ^ ` æ ø å ~ Sweden # ¤ É Ä Ö Å Ü é ä ö å ü Italy # $ @ ° \ é ^ ù à ò è ì Spain I Pt $ @ ¡ Ñ ¿ ^ ` ¨ ñ } ~ Japan # $ @
Tally Dascom DL-210 User Guide V1.3 7.
Tally Dascom DL-210 User Guide V1.3 7.
Tally Dascom DL-210 User Guide V1.3 7.
Tally Dascom DL-210 User Guide V1.3 7.
Tally Dascom DL-210 User Guide V1.3 7.
Tally Dascom DL-210 User Guide V1.3 7.
Tally Dascom DL-210 User Guide V1.3 7.
Tally Dascom DL-210 User Guide V1.3 7.
Tally Dascom DL-210 User Guide V1.3 7.
Tally Dascom DL-210 User Guide V1.3 7.
Tally Dascom DL-210 User Guide V1.3 8 COMMAND SETS 8.1 ESC/POS Command Sets Category Print commands Print position commands Miscellaneous Function Commands Chinese Character control commands Commands Function LF Print and line feed FF Print and feed paper to the head of next page (in page mode) CR Print and carriage return ESC J n Print and feed paper HT Horizontal tab ESC $ nL nH Set absolute print position ESC D n1...nk NUL Set horizontal tab positions ESC \ nL nH Set relative prin
Tally Dascom DL-210 Category User Guide V1.3 Commands Function ESC SP n Set right-side character spacing ESC ! n Select print mode(s) ESC % n Select/cancel user-defined character set ESC & y c1 c2 [x1 d1...d(y × x1)]...[xk d1...
Tally Dascom DL-210 User Guide V1.3 8.
Tally Dascom DL-210 User Guide V1.
Tally Dascom DL-210 User Guide V1.
Tally Dascom DL-210 User Guide V1.
Tally Dascom DL-210 User Guide V1.
Tally Dascom DL-210 User Guide V1.
Tally Dascom DL-210 User Guide V1.3 8.3 EPL Command Sets Commands Function A ASCII text B Bar Code (EAN-8 / EAN-13 / UPC-A / Interleaved 25 / Codabar / UPC-E / Code39 / Code 128) b MaxCode (Data Matrix / PDF417 / QR Code) C Cut Immediate D Density EI Print Soft Font Info. EK Delete Soft Font ES Store Soft Font f Cut/peel position GG Tetrieve Graphics GI Print Graphics Info.
Tally Dascom DL-210 User Guide V1.3 Appendix I: Installing the Cutter Removing the Tear Bar (1) Turn off the printer power and open the top cover and the print head mechanism, and then pull the tear bar to your side. (2) Lift the tear bar up and it can be easily removed.
Tally Dascom DL-210 User Guide V1.3 (3) The tear bar is removed. Note: Do it in reverse steps so as to install the tear bar. Installing the Auto Cutter (1) Power down the printer before installing the cutter. Plug in the cutter connector to the printer.
Tally Dascom DL-210 User Guide V1.3 (2) Put the auto cutter onto the slot of the low casing. (3) Move the auto cutter gently to the reverse board till you hear the click sound.
Tally Dascom DL-210 User Guide V1.3 (4) After installation you can use the auto cutter. (5) Enable the cutter in the setup tool.
Tally Dascom DL-210 User Guide V1.3 Appendix: FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. and 2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Appendix III: DASCOM REPRESENTATIVES GERMANY SINGAPORE (ASIA PACIFIC) DASCOM Europe GmbH Heuweg 3 D-89079 Ulm Deutschland Tel.: +49 (0) 731 2075 0 Fax: +49 (0) 731 2075 100 www.dascom.com DASCOM AP Pte Ltd 21 Bukit Batok Crescent #29-81, WCEGA Tower Singapore 658065 Phone: +65 6760 8833 Fax: +65 6760 1066 www.dascom.com AMERICAS UNITED KINGDOM DASCOM Americas Corporation 34 Lakeview Court Verona, VA 24482 USA Phone:+1 (877) 434 13 77 Fax: +1 (540) 242 7221 www.dascom.
