User's Manual

ManualsBrandsJesmay Electronics ManualsCamera & Photo2.4GHz Wireless Camera System

OWNER’S MANUAL

(PLEASE READ BEFORE USE)

TX RX

2.4GHz WIRELESS CAMERA SYSTEM

0336

JESMAY ELECTRONICS CO., LTD

ROOM 1004, STANHOPE HOUSE

738 KING’S ROAD,

QUARRY BAY, Hong Kong

TEL: (852) 2563 4292, 2562 6212

FAX: (852) 2565 7026, 2516 9417

E-mail: info@jesmay.com.hk

Web Site: http://www.jesmay.com.hk

Summary of content (7 pages)

PAGE 1
2.4GHz WIRELESS CAMERA SYSTEM OWNER’S MANUAL (PLEASE READ BEFORE USE) JESMAY ELECTRONICS CO., LTD ROOM 1004, STANHOPE HOUSE 738 KING’S ROAD, QUARRY BAY, Hong Kong TEL: (852) 2563 4292, 2562 6212 FAX: (852) 2565 7026, 2516 9417 E-mail: info@jesmay.com.hk Web Site: http://www.jesmay.com.
PAGE 2
CHAPTER TABLE OF CONTENTS PAGE 1. Read this first…………………………………………………………2 2. The 2.4GHz Wireless Camera System…………………………..3-8 3. Installation of the system…………………………………………..8-10 4. Trouble –shooting……………………………………………………11 5. Technical specifications…………………………………………..12 1. Important-Safety Precautions This device of which operation is subject to the following two conditions 1. This device may not cause harmful interference, and 2.
PAGE 3
2. THE 2.4GHz WIRELESS CAMERA SYSTEM 2-2 Control Elements, Transmitter 2-1 Packaging and accessories 1 2 3 Fig2 Fig1 4 1. 2. 3. 4. 5. 6. 5 One camera One receiver One set camera Mounting Bracket One 2.4GHz Antenna Two power Adapters (9VDC/300mA) One owner’s manual in English 3 6 1. 2. 3. 4. 5. 6. 7. 8.
PAGE 4
. Channel selection DIP SW (as shown in Fig5) Select the channel by setting the channel DIP SW to the ON position. 1 2 3 4 ON OFF Fig5. CHANNEL SELECT DIP SW Fig3 2-3. Control Element, Receiver Front View of Receiver Rear View of Receiver DIP SW Function: DIP SWS1-4: set one channel or multi–channel sequence function. By setting multi–channel DIP SW to the ON position, channel changes every four seconds 5. Power ON/OFF switch 6.
PAGE 5
B. Fix’s one channel Mode: 1 2 3 4 1 ON OFF o 2 3 1 2 3 4 4 ON ON OFF o OFF Fig 4 Fig 1 Fig 2 Fig 1: Channel 1 is selected. BLUE LED located on front of the Receiver will blink once at intervals of 4 seconds. Fig 2: Channel 3 is selected. BLUE LED will blink 3 times at intervals of 4 seconds. C. Automatic channel sequence mode: 1 2 Fig 4: Channel 1, channel 2, channel 3 and channel 4 are selected in sequence.
PAGE 6
Transmitter Receiver: 9VDC(300mA AC Adapter Supplied 9 10
PAGE 7
4. Trouble –shooting 5. Technical specifications 1. No image or sound a. Make sure the power supply switches on the back of the receiver are in the “ON” position. b. Check correct position of all the connectors and plugs. c. Make sure the transmitter and the receiver are on the same channel . 2. Interruptions in image and sound a. Make sure antenna of the transmitter and the receiver are in correct alignment. b. Adjust the transmitter and the receiver to closer position. c.