JESMAY MODEL: 2036T/R 2.4GHz Wireless Multiway Monitor with DVR Transmit-Receive System OWNER’S MANUAL JESMAY ELECTRONICS CO., LTD ROOM 1004, STANHOPE HOUSE 738 KING’S ROAD, QUARRY BAY, HONG KONG TEL: (852)2563 4292, 2562 6212 FAX: (852)2565 7026, 2516 9417 E-mail:info@jesmay.com.hk Web Site:http://www.jesmay.com.hk (PLEASE READ BEFORE USE) JESMAY ELECTRONICS CO.
CHAPTER TABLE OF CONTENTS PAGE 1. Read this first--------------------------------------------------- 2 2. Technical specifications------------------------------------ 3-4 3. Wireless Multiway Monitor with DVR Feature-------- 5 4. System connect sketch map------------------------------ 5 5. Packaging and Accessories------------------------------- 6-7 6. Control Elements---------------------------------------------- 7-11 7. Installation of the system----------------------------------- 11-14 1.
2. Technical specifications ITEM DESCRIPTION Receiver Frequency 2.4GHz~2.483GHz(4 channels) Receiver sensitivity -80dBm Channel design PLL frequency synthesizes Modulation FM Antenna Omni-directional Image sensor 1/4?Color CCD Picture element 512*582 (PAL), 512*492 (NTSC) IR on illuminance 10LUX ITEM DESCRIPTION Recording Frame Rate Each Channel =30/Number of Source Max. 30 fps NTSC (Each Channel) (Each Mode) Each Channel =25 fps/Number of Source. Max.
3 Wireless Multiway Monitor with DVR Feature Video 4 Channel BNC Camera Input & RF 4 Channel Receive 5 Packaging and Accessories ¦ Multiway Receiver with DVR 2 Channel BNC Monitor Output NTSC / PAL 4 Sets NO/NC Sensor Input 1 Alarm Output (2A 28VDC / 0.
¦ Transmitter 2.4GHz Camera X4 2.
¦ 3) Remote Controller 1. CH1 2.CH2 3.QUAD 4.CH3 5.CH4 6.AV/RF 7.STOP 8.RECORD 9.PAUSE 10.REWARD 11.FORWARD 12.PLAY 13.UP 14.MENU 15.DOWN 16.ENTER 17.PROG-CH1 18.PROG-CH2 Camera control elements F r o n t V i e w o f Cam e r a Rear View of Cam e r a 19.PROG: AV/RF (single) select state 20.PROG-CH1 21.PROG-CH2 1. Rainproof solid aluminum housing 2. 1/4" CCD Color image sensor 4) Removable HDD Box Introduction 3. IR led with CDs control 4. Aluminum body 5. 2.4GHz Antenna 6.
Installation of the system Key Lock ¦ Multiway Receiver with DVR Installation A 1) Install Hard Disk B A: Locked (Non-removable) B: Unlocked (Removable) Slide the carrier body out of the cartridge frame (Fig1) CAUTION 2) Connect Camera and Monitor There are 4 camera input and 2 monitor output with BNC connector. 3) Connect Power Cord DON’T take out HDD when DVR running! Please use power adapter come along with DVR. Fig1 4) 2.
¦ Camera installation 2.4GHz antenna 8 Operating Instruction ¦ Antenna socket Multiway Receiver with DVR Operating 1)DVR System Boot ? Detect Installed Hard Disk After connect the power, system will boot-up and detect installed HDD Checking……….. MASTER HARD DRIVE IBM—DHEA—36481 SLAVE HARD DRIVE hard disk. Monitor will show Master and Slave hard-disk information. Please reference hard disk manual to configure hard disk Transmitter sequence. (Master or Slave) Note: Attach 2.
? Menu Main Screen Directory Camera Select At first time DVR boot-up, all Record Select cameras are OFF, please follow Record Mode chapter 5-2 to switch on all Record Frame Rate Main Menu cameras. Video Quality Record Schedule λ Upper left Ratio of Hard Disk Space Used λ Middle ~ Hard Drive Setup Channel Name( CH1 Date and Time At the moment, DVR is waiting for command, press ? Menu ? into DVR setup process or ? Play? , Record? .
? Quad Mode? : Compress and record all 4 channel video into one file, therefore use can not enlarge single channel to full screen. ? Sub Menu—Password All keys can use as ? Record Frame Rate Record frame rate will affect the movement of object in recorded video. More frames means more smooth movement and cost more hard disk space. password key except? Menu? key is use for System default value is 30 fps, it means system will record 30 frame per cancel input and exit. second.
λ MASTER HDD USED It shows the space used on the first hard disk drive for recording. λ MASTER HDD FORMAT If you format the hard drive, it will erase all the data recorded on the first hard disk drive. λ λ λ SLAVE HDD SIZE It shows the space the secondary hard disk drive installed in the DVR. λ Push the UNLOCK BUTTON to insert the wire SLAVE HDD USED λ There are 3 different modes for sensor setting: It shows the space used on the primary hard disk drive for recording.
?12 NTSC/PAL Output Select Change jump JS1 to select NTSC or PAL video output format. λ ? HD Info. ([M] Master disk [S] Slave disk) λ ? Schedule((T) Continuous (S) Sensor (- ) No Record λ ? When ? * ? show up beside date & time , it indicate that system are overwrite. ? Stop Recording Press? Stop? and system will prompt to input password. Only correct password can stop recording process. Format NTSC 3) DVR Record ? Start Recording Press ? Record? to start record.