corresponding˰setting˱and press˰Enter˱to enter regional setting interface. The blue area means motion detection is activated, transparent block means motion detection is not activated. Press the direction key on remote control to move the cursor along the small pane: position of cursor is indicated by green frame. Press˰Enter˱to select or cancel motion detection in this small pane.
5.7.4 PTZ Data Bit Options include 5, 6, 7 and 8.The default setting for DATA BIT is 8. 5.7.5 PTZ Stop Bit Options include 1 and 2. The default setting is 1. 5.7.6 PTZ Parity Options include None, Odd, Even, Mark and Space. The default setting is none. 5.7.7 PTZ Address Select the PTZ device ID. It must be consistent with the ID of the actual PTZ cameras installed. Make your choice of any number from 1 to 255.
6.2 Network Security Setting Prior to control installation, please program the network security level by using the following operations: (1) Open the IE browser and click [Tools Internet Options]. (2) Choose the “Security” label in the dialogue box. (3) Click “Customization level” to enter into the security setting. Set the ActiveX control and pluggable unit.
Perform the ActiveX control and pluggable unit It’s extremely importation to “enable” the items above. Prompt: Before control installation, please turn off the fire wall and the anti-virus software. 6.3 Connection Setting The remote access for the hard disk recording machine should be carried out through the network. In the local area network connection, the IP address of the client-side computer must be in the same network section with that of the hard disk recording machine.
Step 4: Double click “Internet protocol (TCP/IP)”. Step 5: Examine the IP address, subnet mask, and default gateway on the PC. Step 6: Set the corresponding IP address, subnet mask, and default gateway on the DVR (refer to 5.5.5 Network Setup). If the subnet mask and default gateway on DVR are the same with those of the PC, then the IP address must be in the same network section but cannot be the same with the used one. Otherwise, it will cause IP address conflicts.
download and install the control automatically. After connecting to the internet, IE will automatically download the file to PC as follows. The system will automatically enter GUI as follows. Select English interface from the top left side. Input correct password if password is enabled to enter the system. The password is the same as the one set in DVR. USER ID: Input user name. The administrator has all authorities, but common user has been limited authorities by administrator.
6.5.2 Control Move cursor to the icons, which will become highlighted when selected. Connect all windows or disconnect all windows. Capture picture, save in local disk, system save default path is “c:\DVR\BACKUP\”. Quick-start to record video on all channels. The left upper corner of each channel has normal recording video symbol . Click icon to switch between single screen /quad /nine /16 split /full screen . Adjust the volume. 6.5.3 Other Operation 1.
Click “REPLAY” to enter into playback interface. and , to set the month for searching; click Click right up of calendar interface “REFRESH” at the calendar interface to display the recording information of current month. The highlighted date indicates that video was recorded on that day. Click on a date to search the recording file list of that day. For example, the above fig shows that June, 12th, 13th have recorded video when it shows on bold, and current search date is June 12th.
The user can download files on PC, and save them to HDD for backup or play. Download file format is AVI file. 6.5.5 Instruction Of Toolbar Play Stop Fast play Pause Volume Control Slow Play Single Frame 6.5.6 Remote Setting Click [Remote Setting] to enter into setup interface, this interface includes record, alarm, PTZ, network, advanced and system information six menus. A. Encode Setting Click [Encode Setting] – [Video Para] to enter into setup interface.
C. Alarm Setting Click [Alarm Setting]-[Device Alarm] to enter into setup interface. Click [Alarm Setting]-[Channel Alarm] to enter into setup interface. User can set up alarm event types; also can set I/O alarm for each channel, motion detection alarm, motion area, motion sensitivity, alarm out time, buzzer time, pre REC time and post REC time.
D. PTZ Setting Click [PTZ Setting] to access setup interface. User can setup PTZ parameters remotely using the same methods as in the local DVR setup. E. Network Setting Click [Network Setting] - [Network] to enter setup interface. The menu allows user to set a lower bandwidth for Internet video transmission. Click [Network Setting] - [Mobile] to enter setup interface. Click [Network Setting] - [Email] to enter setup interface.
F. System Setting Click [Advanced Setting] - [System Setting] to enter setup interface. The menu allows user to set daylight saving time.
G. System INFO Click [System INFO] - [Version INFO] to enter setup interface. Here user can check the device’s ID and software version. Click [System INFO] - [HDD INFO] to enter setup interface. Here user can check HDD state, total size of HDD and free size of HDD. H. User Manager Click [User Manager] - [ADD OR DEL] to enter setup interface. This interface could only been seen by administrator when password is available. Administrator can add new user or delete any user.
Click [User Manager] - [MODIFY PASSWORD OR PRI] to enter setup interface. This interface could only be seen by administrator when password is available. Administrator can change password, local authority and remote authority. 6.5.7 Local Setting Click [Local Setting] to enter setup interface. User can setup the save path for local setting. “Record save path” is for recording, “Frame save path” is for capture and “File save path” is for download. Click the button “ ” to setup save path.
6.5.8 Logout Click [Logout] to log out of the system. 7. WAP CONNECTION The digital video recorder can also be remotely accessed by using a web browser installed on a mobile phone that support xHTML and MJPEG file format, and has screen resolution at 320x240 or above. Then follow this step to access the digital video recorder. 1. Make sure the digital video recorder connects to Internet accurately. 2. Open Internet Browser on mobile phone and fill in IP address of DVR.
4. After logging on system successfully, there will be a setting page. You can set channel you want to monitor, picture size and the refresh time. Click “OK” to take them effect. 5. Now you can get picture from the monitor channel. The picture will refresh in several seconds automatically if you had chosen a refresh time in setting page. While you have chosen manual as refresh mode, it won’t refresh automatically until you click “refresh”.
onto your Windows Mobile phone. See your phone user manual for more details on installing this application. Find and execute program “MobileEye”. Click the Setting button to setup the IP address for your DVR. In the following screen, input the User Name, Password, Server (IP address for your DVR) and Port (default 10510). Next, choose the channel Count for streaming data from the drop-down menu and choose the Default Channel when connecting. Choose a Record Name for your favorite files.
8.2 Symbian S60 3rd Phone From the installation CD, install file “xxx.sisx” onto your Symbian S60 3rd Edition mobile phone (for the list of mobile phones tested for compatibility, please see “List of Symbian Supported Mobile Phones”). For instructions on installing software onto your mobile phone, please refer to the phone’s user manual. Note: Prior to using this feature, you should apply for an Internet connection service for your mobile phone, such as 3G or 2.5G.
Default Access Point: Choose the network through which you connect to the Internet. The options are: “None”, “WAP over GPRS”, and mobile service providers operating in your country. If you choose “None”, then after pressing the button you will be offered a list of available networks to choose from.
Select channels. If your system supports 8-channels, use functional button switch between channel buttons 1-4 and 5-8. to PTZ camera direction controls PTZ camera Zoom, Focus and Iris controls Functional buttons: When highlighting these buttons, the name of the corresponding function will be displayed in the status information line (the first tag name). Play / Stop Use these buttons to play and stop the video. Full screen This function displays the camera feed in the full-screen mode.
List of Symbian Supported Mobile Phones Please review the list of Symbian mobile phones tested for compatibility with the remote access to DVR.
Nokia N71 S60 3rd_INIT 09-Nov-05 Nokia N73 S60 3rd_INIT 09-Apr-06 Nokia N75 S60 3rd_INIT 27-Sep-06 Nokia N76 S60 3rd_FP1 08-Jan-07 Nokia N77 S60 3rd_INIT 12-Feb-07 Nokia N78 S60 3rd_FP2 11-Feb-08 Nokia N79 S60 3rd_FP2 21-Aug-08 Nokia N80 S60 3rd_INIT 09-Nov-05 Nokia N81 S60 3rd_FP1 29-Aug-07 Nokia N81 8GB S60 3rd_FP1 29-Aug-07 Nokia N82 S60 3rd_FP1 14-Nov-07 Nokia N85 S60 3rd_FP2 21-Aug-08 Nokia N86 8MP S60 3rd_FP2 17-Feb-09 Nokia N91 S60 3rd_INIT 14-Apr-05 Nokia N9
8.3 Apple IPhone 1) MobileEye installation Open iPhone App store “ ” as follows: Fig 1 ķ ClickȾ ȿbutton and search for “MobileEye”. It is a free application. Fig 2 ĸ Click “ ” and you will see following screen.
Fig 3 Ĺ Click “ ” as shown in Fig 3. It will display the screen shown in Fig 4. Click the “install” button shown in Fig 4 “ ” and it will display the screen shown in Fig 5. Input ”. The screen will look like the one your Apple account password, then click “ shown in Fig 6.
Fig 6 “ “ ”waiting: indicates that the “MobileEye” software is downloading ……. ” process bar displayȾ When the ȿstatus, the MobileEye software has finished installing. After installing “MobileEye”, the iphone screen will display the screen shown in Fig7. Fig 7 2) How to use MobileEye Ł Click the “MobileEye” icon to open the “MobileEye”.
ķPTZ arrow control(up down left right) ĸPTZ lens control(zoom+, zoom-), (focus+, focus-), (iris+, iris-). ĹSelect the live view channel. ĺShortcut key, including pause, capture, full screen, next channel grouping and settings. ĻExit ł When you enter the Setting menu, the window below is shown: ķServer IP: DVR Internet address. ĸPort: Default 10510.
8.4 Andriod Mobile 1). Install the program 1. Copy the setup software “Mobile Eye-Android.apk” to your computer. 2. For instructions on installing software onto your mobile phone, please refer to the phone’s user manual. Note: Prior to using this feature, you should apply for an Internet connection service for your mobile phone, such as 3G or 2.5G. Please contact your mobile service provider for details. 3. Install a HTC manager “HTCSync.exe” on your computer.
Select option “Application Installer” and click the left mouse, then the user can find the setup file; install “Mobile Eye-Android.apk” on your mobile telephone according to the following method.
Please ensure that if asked, you allow the application access to the internet. When application has finished installing, your phone may show the following screen. 2). System explanation Mobile Eye application mainly allows: live video surveillance, channel switching, full screen viewing, PTZ control, focus, and image capture, save as favorite and exit function. 2.
Below is displayed the main start page of the application: Switch Video Snapshot Full Screen PTZ Control ZoomˣFocusˣIris 2.2) System setting interface Press the [setting] button to access the parameters settings. You will need to use this for the first time you use the system and later if you want to change the parameters of the system.
Save as favorite: Save settings for future usage; User name: The device ID which is set on DVR [phone surveillance]; Password: The user password which is set on DVR [phone surveillance]; Server: The public IP address or dynamic domain name of DVR Port: The server port which is set on DVR [mobile phone]ˉdefault is “10510”. Channel Count: Set the number of channels accessible from the DVR Default channel: Set the default channel shown when connected to the DVR. Record Name: Save the name of the record.
See below for more details: 烉Press this icon to connect to the DVR : Press this icon to open the settings menu : Change live view channel. 烉Use the arrows to move the PTZ up, down, left and right. : These icons operate the zoom, focus and iris. 烉This function will capture the current viewed image. 烉Press it to enter into full screen mode, press it again back to the common mode.
8.5 Blackberry Mobile 1) Program installation 1. Copy the setup software “MobileEye.cod” and “MobileEye.alx” to your PC. 2. In order to be able to install applications and themes via BlackBerry Desktop Manager, firstly the PC should install Blackberry Desktop Manager. BlackBerry Desktop Manager will be known as “DM.”; otherwise the phone cannot establish the connection with the PC. 3. Connect your BlackBerry mobile phone to your computer via the USB cable that came with it, or any USB cable that fits.
5. Click on “Application Loader” to enter into its interface. In this screen you have two options to select from. Select “Add/Remove Applications” (shown as follows). 6. You should now see something like what you see below. From this screen, click “Browse” (shown as follows). 7. Once you click “Browse” you will see a file search screen like the one below. Go to and locate where you saved the application files. Make sure you saved both the “.alx” file and “.cod” file in the same folder.
8. You will now return to the Application Loader screen. From here you should see “MobileEye” now listed with Install under the Action column (shown as follows) if the installation is successful. 9. You can remove the program “MobileEye” as the following method. To enter into Application Loader screen, on “Device application selection” you can select the application that you want to clear from your device. When the option “Action” is “Remove”, it means the program will be clear from your device.
10. Click “Next” and the screen will show as follows. Click “Finish” to confirm and the application “MobileEye” can be removed from your device. 2) System explanations MobileEye phone port has the following capabilities and functions: live video surveillance, channel switch, full screen display, PTZ control, including zoon/focus/iris, image capture, save as favorite and exit function. ķ System main interface After the installation, press “MobileEye” icon in the application, see the below picture.
Open the main interface, see the below picture. ĸ System configure interface Press [Configure] button to access to the parameters setting when using for the or as needed to change the settings. Modify your parameters as necessary.
Record lists: The record which is saved can be found here; User name: The device ID which is set on DVR menu [phone surveillance]; Password: The user password which is set on DVR menu [phone surveillance]; Address: The public IP address and dynamic domain name of DVR. Port: The server port which is set on DVR menu [mobile phone]. Default is 10510. Record name: Save the name of the record. After the setting press [SAVE] then it will go to the favorite folder. Next time you can find the record in the file.
See below for more details: Choose Channel烉This function switches the channel. It may only be enabled AFTER connecting to the DVR. : This function moves the PTZ up, down, left and right. 烉This function operates the zoom, focus and iris. : Press it to enter full screen mode, press it again to go back to common mode. : Use this function to capture images. ĺ Connect to DVR To connect to the server, press the menu button on your mobile phone it will bring up menu as follows.
ĻSystem Help interface After the setting, back to the main interface and press [Help] button to enter into the help interface. ļSystem Exit interface To exit, go back to the menu interface and press [Exit] button.
Troubleshooting This basic troubleshooting guide will help you identify general malfunctions and offer steps for quick resolution of such. If the failure or malfunction can't be solved by following these steps, please contact a qualified technician. 1. DVR is not working after starting. What happened烎 Check the adaptor input. Check the on-off power line, is it well-connected? Check the power on-off. Check the upgrade procedure. Check the main board of DVR. 2.
Make sure HDD is formatted. Check the power and data connection cables of the HDD. The HDD could be defective. The SATA port may be not working. 5. What if the DVR is having problem with real-time images, such as bad image color or serious brightness distortion If PAL or NTSC is not correctly selected on the BNC output, the images will be in black and white. Make sure the DVR is compatible with monitor. Make sure the video transmission distance is too far.
Check the sensitivity of the motion detector. Maybe the sensitivity is too low. 11. What if the remote control cannot work? The address of remote control may be incorrect. The distance of remote control may be too far or the angle may be too large. Check the remote control batteries Make sure that the remote control is not damaged or the front panel of the DVR is not damaged. 12. Why can’t login to the WEB? Please check the network to see if it is connected.
Appendix 2 Compatibility Table for HDDs Please find below the list of tested Hard Disk Drives, found to be compatible with the DVR. If you want to use a HDD not found in this list, please test it for compatibility before use.
7.0.517.36 as an example ) 2. After installing Chrome browse, search for additive file for IE TAB, and this file is named “extension_1_4_30_4.crx”. (This file can be loaded from relevant website) 3. Open chrome browser, fill in the IP address of your DVR into address bar, enter it and it will be showed as below Fig. 4. Drag additive file into browse interface and the interface will show as follow. 5. Select “Allow” to download multiple file and the interface will show as follow. 6.
Note: If the web page still can not open, you can press the icon” page in an IE based-tab. ”on the right hand to display this 8. Fill in your correct user name and password to login. Appendix 6 How to use Auto ID "Plug n play" Quick Guide 1.The ID number of the product has been set up in the factory .Click [tool bar]炼 [system setting]炼[user]炻The screen will display user manager menu, and you will see the ID number.
2.Then open the menu, click [Network]炼[Other settings]炼[Auto ID], to open the Auto ID. 3. About using the router to search internet. At first you should mapped the transmit codex of the router’s port. Or open the UPNP, then the router will mapping the port automatic. 4. When the network has been connected, in the anther independence INTERNET circumstance, input the address: http://www.ipremoteview.com in the IE at your PC. And then input the ID of the DVR into the product number as below to search.
5. After the page layout connected succeed. It will switch to the IE interface self-motion. As following.
