MP1516BT Mobile Audio System Owner’s Manual 160 watts peak 40W x 4
Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen MP1516BT Mobile Audio System for maximum enjoyment.
MP1516BT CONTENTS FEATURES �������������������������������������������������������������������������������������������������������������� 4 WARNINGS BEFORE INSTALLATION �������������������������������������������������������������������� 5 INSTALLATION TOOLS ������������������������������������������������������������������������������������������ 7 BEFORE YOU INSTALL ������������������������������������������������������������������������������������������� 7 Remove the Old Unit from the Dashboard ��������
CD/MP3/WMA OPERATION ���������������������������������������������������������������������������������30 Loading a Disc ��������������������������������������������������������������������������������������������������30 Ejecting a Disc ��������������������������������������������������������������������������������������������������30 Selecting a Track ����������������������������������������������������������������������������������������������30 Pausing or Resuming Playback ������������������������������
MP1516BT WARNINGS BEFORE INSTALLATION Important warnings to take note of BEFORE installing the unit: Damage caused by incorrect installation or usage is NOT covered by the warranty. PLEASE take the time to read the installation instructions carefully. To validate the warranty please ensure that the unit is installed by a professional, VAT registered car audio installation company. • To avoid shorts in your vehicle’s electrical system, be sure to disconnect the battery cable before beginning installation.
• If this unit is installed in a vehicle that does not have an ACC (accessory) position on the ignition switch, the red lead of the unit should be connected to a terminal coupled with ignition switch ON/Off operations. If this is not done, the vehicle battery may be drained when you are away from the vehicle for several hours. • Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts.
MP1516BT • If noise is still experienced when the motor of the vehicle accelerates, a choke should be placed in line with the power to the unit. The installation company will know what is required. • When replacing the fuse(s) the replacement must be of the same amperage as shown on the fuse holder. Never replace a fuse with another fuse of a different value. If the fuse blows again please contact your installation company.
Remove the Old Unit from the Dashboard 1. Remove the outer trim frame. DIN Front Mount 2. I nsert the keys supplied with the old unit into both sides of the unit as shown in figure below until they click. Pull to remove the old unit from the dashboard. Do not disconnect wires at this time! Mark the Polarity of the Speaker Wires Marking the polarity of the speaker wires will make it easier to connect the existing speakers to your car radio.
MP1516BT INSTALLATION It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen MP1516 Mobile Audio System installed by a reputable installation shop. WARNING! Disconnect the negative battery terminal from the battery before starting installation. Consult the vehicle’s owner’s manual for proper instructions. NOTE: Mark the polarity of the existing speaker wires before disconnecting battery.
Remove the Transport Screws Before Installation Remove the two transport screws from the top of the unit before installing the unit. Remove screws before installation. DIN Front Mount (Method A) Installation Opening This unit can be installed in any dashboard having an opening as shown below: Installing the Unit Be sure you test all connections first, and then follow these steps to install the unit 1. After removing the old radio and mounting sleeve, insert the supplied mounting sleeve into opening.
MP1516BT 2. B end the tabs on the mounting sleeve to keep the mounting sleeve firmly in place. 3. A ttach the wires from the unit to existing wires. See the wiring connections diagram. Insert the radio into the dashboard. Then apply the trim frame to the outside of radio. 4. S upport the radio using the supplied rear mounting bolt and steel bar. See the parts list.
DIN Rear Mount (Method B) This method of installation uses the screw holes at the sides of the unit and the holes of the existing vehicle mounting bracket. This is only intended as a general guide; contact the vehicle’s manufacturer for specific instructions. NOTE: O uter trim frame, hook, and mounting sleeve are not used for this installation. 1. Remove the hooks on both sides. 2. A lign the screw holes of the mounting bracket supplied with the car and the screw holes of the main unit.
MP1516BT USING THE DETACHABLE FACEPLATE Removing the Faceplate 1. Press the (release) button on the faceplate and pull off the faceplate. Release Button Faceplate 2. Keep the faceplate in the protective case.
Installing the Faceplate To install the faceplate, insert the faceplate into the housing and make sure it is properly installed. Otherwise, the display may appear to be abnormal or some buttons will not function properly. Handling Precautions 1. Do not drop the faceplate. 2. D o not put pressure on the display or control buttons when detaching or reinstalling the faceplate. 3. Do not touch the contacts on the faceplate or on the main unit body. It may result in poor electrical contact. 4.
MP1516BT WIRING CONNECTIONS External Microphone Jack Antenna socket RCA OUT left=white right=red ISO-connector A Fuse 10 A B Connector A 1. Rear right speaker (+) /Blue 2. Rear right speaker (-) /Blue-White 3. Front right speaker (+) / Grey 4. Front right speaker (-) / Grey-White 5. Front left speaker (+) / Green 6. Front left speaker (-) / Green-White 7. Rear left speaker (+) / Brown 8. Rear left speaker (-) / Brown-White Connector B 1. No connection 2. No connection 3. No connection 4.
Black Ground Wire Connect the Black Ground wire to the vehicle body/chassis. Make sure that you have a good chassis ground. Good ground connections will eliminate most electrical noise from the motor and alternator. A good chassis ground requires a tight connection to the vehicle’s metal chassis. The area around the ground connection should be clean, bare metal without rust, paint, plastic, dust or dirt.
MP1516BT CONTROLS AND INDICATORS 1. 2. 3. 4. 5. 1 2 3 4 25 24 23 22 27 5 6 7 21 20 19 8 18 17 9 16 15 14 10 13 12 11 26 (Next Track / Fast Forward) Button During disc play, this button is used to quickly select the end of a particular track in the forward direction. With each press of the button, the next higher track number will be selected as shown on the display panel.
6. S T (Stereo) Button In FM radio mode, press this button to switch between stereo and mono mode of reception. 7. Disc Slot With the label surface facing up, fully insert a compact disc into the slot until the load mechanism engages. Note: T his unit is designed for play of standard 5” (12 cm) Compact Discs ONLY. Do not attempt to use 3” (8 cm) CD-Singles in this unit, either with or without an adapter, as damage to the player and/or disc can occur.
MP1516BT 19. 2 / INTRO (Introduction) Button Press this button to play the first 10 seconds of each track. Press this button again to resume playback. 20. 1 / (Play/Pause) Button Press this button to pause playback. Press this button again to resume playback. 21. Mute Button Press this button to mute the audio. Press this button again to unmute the audio. 22. SCN (Scan) Button In radio mode, pressing this button will enter the scan mode.
REMOTE CONTROL OPERATION Battery Installation The remote control comes with a battery already installed with a Pull Tab to prevent battery discharge. Remove the Pull Tab before attempting to use the remote control. Note: T he remote control will only operate this device. It is not a universal remote control and will not control other equipment. Remote Control Back View Protective Pull Tab (Clear Plastic) To replace the batteries: 1.
MP1516BT Using the Remote Control 1. oint the Remote Control at the remote control receiver on front panel of the P unit. Make sure that the signal path is not obstructed. 2. Press the function keys on the handset to control the system. Note: The maximum distance at which signals can be received is about 6 feet. Do not drop or throw the remote control. Do not place the remote control in a location that is exposed to direct sunlight or next to a heating unit or other heat source.
2. V OL Button Press this button to increase the volume. 3. SEL (Sound Select) / MENU Button Press this button select the audio function (bass, treble, balance, fade or loudness) to be adjusted. VOL Button Press this button to decrease the volume. 4. 3 / RPT (Repeat) Button Press this button to repeat the current track. Press this button again to cancel the repeat function. 5.
MP1516BT 12. F /PS Button In FM or AM mode, press and hold this button to activate the preset scan and save function. In USB/SD mode, press this button to access the folder or directory search function. 13. (Hang Up) / DISP Button In Bluetooth mode, press this button to hang up or reject an incoming call. 14. (Pair) Button In Bluetooth mode, press this button to initiate the pairing process. 15. (Pick Up) Button In Bluetooth mode, press this button to pick up a call. 16.
BASIC OPERATION Turning the Unit On or Off Press the (Power On/Off ) button, or press and hold any button to turn the unit on. The message “JENSEN” appears on the display panel, indicating the unit is ready for use. When the unit is on, press the (Power On/Off ) button to turn the unit off. Selecting an Audio Source Press the SRC button on the faceplate or the MOD button on the remote control to select radio, auxiliary device or disc play.
MP1516BT Sound Adjustment Mode The sound adjustment mode allows you to easily adjust your mobile audio system to meet the acoustical characteristics of your vehicle. To adjust the bass: 1. Press the volume knob or press the SEL button on the remote control repeatedly until "BAS" appears on the display panel. 2. Rotate the volume knob to adjust. When an equalizer preset is ON, bass control is not available. To adjust the treble: 1.
Loudness Control Loudness automatically alters the frequency response curve of audio to make it sound more natural when played at a lower volume level. 1. Press the volume knob or press the SEL button on the remote control until “LOUD OFF” appears on the display panel. This indicates that the loudness function is OFF. 2. Rotate the volume knob to select ON or OFF. Turning the Preset Beep Sound On or Off An audible beep tone confirms each function selection. 1.
MP1516BT RADIO OPERATION Choosing a Radio Band Press the SRC button on the faceplate or the MOD button on the remote control to select radio mode. The radio frequency appears in the display panel together with the frequency memory band (FM1, FM2, FM3, AM1 or AM2). The unit has five preset memory bands - three FM Bands (FM1, FM2, and FM3) and two AM Bands (AM1 and AM2). Each of the five bands can store up to six preset stations, for a total of 30 preset memory stations.
Saving Your Preset Stations There are six numbered preset buttons which can store and recall stations for each band. While listening to a radio station you would like to save as a pre-set, press and hold one of the buttons numbered 1-6 until you hear a beep. The button you pressed is now the preset button for that station. Automatic Scan and Store The Automatic Memory Storing feature is most useful when travelling in an area where you are not familiar with the local stations.
MP1516BT Selecting an FM Station by Program Type (PTY) This radio will allow you to select the type of program required, and will search for a station broadcasting that type of program. 1. Press the CLK/PTY button until the program type and “PTY” appears on the display panel. 2. Immediately press the CLK/PTY button again, then press the 1 - 6 button to choose the type of program. Press the number button repeatedly to choose a program type as shown in the table below.
CD/MP3/WMA OPERATION Loading a Disc Insert a disc into CD slot with label side up. The disc will be automatically loaded into the unit, even when it is off or in radio mode. The word “LOAD” will blink on the display panel and the CD will play automatically. Ejecting a Disc Press the (Eject) button to eject the disc from the slot. If the disc is not removed from the slot within 5 seconds, it will automatically be loaded into the slot again.
MP1516BT MP3/WMA Playback While you are playing a disc with MP3 or WMA files, the first file in the root folder will be played. As the file is playing “MP3” or “WMA” will be displayed first, then if there is any ID3 information that will be displayed as the file is playing. Displaying ID3 Tag Information While you are playing an MP3 file which has ID3 Tag information, press the BAND/ ID3 button repeatedly to show the ID3 Tag information on the display panel.
Multi-Session CD Reading This unit can read multi-session CDs. The multi-session reading will be activated automatically if the player detects a file that is written in multi-session format. Electronic Skip Protection The unit is equipped with Electronic Skip Protection (ESP) circuits. Electronic Skip Protection is for driving on rough roads. The CD will play for 10 seconds on rough roads without skipping. If driving on a rough road for more than 10 seconds, the CD may skip.
MP1516BT Disc Notes Notes on discs: • This unit will only play the following discs: Type of Disc CD, MP3, WMA Label on the disc Recorded Material Size of Disc Audio only 12 cm • This unit only reads 12 cm discs. • Do not use irregularly shaped discs such as heart or star-shaped discs as they may cause the unit to malfunction. Be sure to use round shape CD discs only for this unit. • Do not stick paper or tape, etc, onto the label side or the recording side of any discs, as it may cause a malfunction.
Cleaning and Handling Discs To enjoy the best sound quality, handle discs as indicated below: • Clean the discs with a cleaning cloth. Clean each disc from the center to the outside edge. • Don’t use CDs with blobs of glue or ink on its surface. • Don’t use CDs with labels or stickers on its surface. If the labels start to rub away, any remainder of glue can interfere with the good performance of the unit. • Hold and handle discs by the edges to keep the disc clean. Don’t touch the surface of the disc.
MP1516BT USB OPERATION The unit contains a USB port. The USB port is located on the faceplate beneath the protective cover. You can connect an USB memory device using this port. 1. Locate the USB Input Cover on the faceplate. USB Input Cover 2. Lift the USB Input Cover to reveal the USB connector. 3. Insert the USB device into the USB connector. The unit will read the audio files on the USB device automatically. “USB PLAY” appears on the display panel. 4.
MEMORY CARD OPERATION There is an SD Memory Card Slot on the housing of the unit. The housing is accessed by removing the faceplate. 1. Press the release button on the faceplate. Release Button Release Button Faceplate 2. Pull off the faceplate to reveal the Memory Card slot. Faceplate 3. Insert an SD card into the Memory Card slot. Memory Card Slot 4. I nstall the faceplate. The unit will search the MP3 files in the card and start to play MP3 files automatically.
MP1516BT MP3/WMA Playback To play MP3/WMA files from a SD card, remove the faceplate and insert a SD card into the SD Memory Card Slot on the housing. The unit will start playing MP3/ WMA files on the SD card memory automatically when the faceplate is installed. If the MP3/WMA files are stored in folders on the SD card, the unit will start by playing the first song in the first folder.
iPod®/iPhone® OPERATION An iPod or iPhone device can be connected to the unit via your iPod cable to the USB interface on the front panel. Once connected, “FLASH IPOD” appears on the display panel, then playback starts automatically. When the unit is in another mode of operation, press the SRC button on the front panel or the MOD button on the remote control to select iPod mode. Browsing your iPod/iPhone ress the AS/PS button on the front panel or the F/PS button on the remote P control.
MP1516BT BLUETOOTH® WIRELESS DEVICE OPERATION Wireless products featuring Bluetooth technology have the capability to wirelessly synchronize and transfer data among devices. The Bluetooth audio capabilities can be used for mobile phones hands free applications. Bluetooth wireless technology has many profiles and the unit is compatible with most mobile phones featuring Bluetooth wireless technology.
5. A t this point a prompt stating that pairing is successful should appear. Another prompt should appear asking connect to the unit, Yes or No. Press Yes. The mobile phone and the unit should connect. The mobile phone should display a message similar to “Device Connected.” The mobile phone and the unit are now connected. When successfully paired, “BT CONNECTED” appears on the display panel. Note: I f pairing fails, try to pair again within several seconds. Refer to the mobile phone’s instruction manual.
MP1516BT • DIALED: Display the last 10 dialed numbers. Press the or buttons to scan the numbers. Press the the number. • MISSED: Displays the call you have missed. Press the or buttons to scan the numbers. Press the the number. button to dial button to dial Managing Incoming Calls Answering an Incoming Call Press the button to answer an incoming call. Rejecting an Incoming Call Press the / DISP button to reject the incoming call. Making Outgoing Calls Outgoing calls can be made in two manners.
Transferring a Call 1. hile talking, press the W button to transfer the phone call between the mobile phone and the unit. 2. Press the button answer to transfer the phone call back to the head unit. Note: I f you transfer a call to mobile phone, the mute function is cancelled and the unit will return to the mode it was in prior to the call. Adjusting the Bluetooth Default Volume To adjust the Bluetooth playback default volume: 1. Change the source to BT AUDIO. 2.
MP1516BT SPECIFICATIONS CEA Power Ratings Power output: 13 watts RMS X 4 channels into 4-ohms @ < 1% THD+N Signal to noise ratio: 70dBA below reference. (Reference: 1 watt, 4-ohms) Frequency response: 20Hz to 20kHz (-3dB), Auxiliary input used as source reference Reference supply voltage: 14.4VDC CD Player Signal-to-noise ratio: >90dBA Frequency response: 20Hz-20kHz, -3dB Channel separation: >55dB @ 1kHz D/A converter: 1 Bit/CH FM Tuner Tuning range (USA): 87.5MHz - 108.00MHz Tuning range (Europe): 87.
TROUBLESHOOTING Before going through the checklist, the check wiring connections. If any of the problems persist after checking the list, contact your nearest service dealer. Problem Cause Solution No power. • The car ignition switch is not on. • If the power supply is connected to the car accessory circuits, but the engine is not running, switch the ignition key to “ACC”. • Replace the fuse. Make sure the amperage matches the specified value. • The fuse is blown.
MP1516BT Problem Cause Solution The operation keys do not work. • The built-in microcomputer is not operating properly due to noise. • Press the RESET button. • The faceplate is not properly installed. The radio does not work. • The antenna cable is not connected. • Insert the antenna cable firmly. The radio station automatic selection does not work. • The signals are too weak. • Select a station manually.
CARE AND MAINTENANCE 1. 2. 3. 4. 5. 6. 7. 8. se only a clean silicon cloth and neutral detergent to clean the front panel. U A rough cloth and non-neutral detergent (such as alcohol) may result in scratching or discoloration. Do not get water or cleaning fluids on the unit. Do not use petroleum distillates to clean this unit. Insert only 5” (12 cm) compact discs into the player. The mechanism can be damaged by foreign objects.
MP1516BT COMMON REPLACEMENT PARTS Detachable Faceplate 30213850 Owner’s Manual Kit 30613850 Wire Harness 30313840 Trim Ring 30413840 Main Sleeve 30113840 Hardware Bag 30513840 Remote Control 30713850 Microphone 34413850 47
Audiovox Electronics Corporation Hauppauge, NY 11788 Technical Assistance: 1-800-323-4815 www.mobile.jensen.