JCD2010 MOBILE CD PLAYER / RECEIVER Installation and Operation Manual
JCD2010 SAFETY INFORMATION DISC NOTES When Driving Compatible Disc Types Keep the volume level Iow enough to be aware of your surroundings. Table 1: General Disc Information When Washing your Vehicle Do not expose the product directly to water, as this can cause electrical shorts, fire or other damage. Disc Type Diameter/ Playable Sides Logo When Parked Audio CD Exposure to direct sunlight for an extended period of time can produce very high temperatures inside the mobile unit.
JCD2010 6. INSTALLATION Before You Begin 1. 2. Disconnect Battery Before you begin, always disconnect the battery negative terminal. Remove Transport Screws 7. 8. Important Notes • • • • • • • Before final installation, test the wiring connections to make sure the unit is connected properly and the system works. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
JCD2010 DIN Rear Mount (Method B) This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some vehicles to mount the radio to the dashboard. Please consult with your local mobile stereo shop for assistance on this type of installation. 1. 2. 3. 4. 5. Remove the existing factory radio from the dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio.
JCD2010 +12V DC SWITCHED WIRING PIN NO.
JCD2010 BASIC OPERATION Volume Level Use the button to adjust the Volume level from “00” (lowest) to “63” (highest). Bass Level 1 16 3 5 21 2 Use the button to adjust the Bass (BA) level range from “-7” to “7”. Treble Level Use the button to adjust the Treble (TR) level range from “-7” to “7”. Balance Use the button to adjust the Balance (BL) between the right and left speakers from “9L” (full left) to “9R” (full right). “BL:0” represents an equal balance between the right and left speakers.
JCD2010 Automatically Store / Preset Scan (AS/PS) TUNER OPERATION Automatically Store 1 16 3 5 21 Select a band (if needed). Press and hold the AS/PS button (16) for more than 2 seconds to automatically select six strong stations and store them in the current band. The new stations replace any stations already stored in that band. 2 Preset Scan Select a band (if needed). Press AS/PS (16) to scan stations stored in the current band. The unit will pause for seven seconds at each preset station.
JCD2010 CD OPERATION 1 15 Press the RDM 4 button (12) on the control panel during disc play to play all tracks on a CD in random, shuffled order. Press RDM 4 again to stop random play. 16 3 5 7 Random Play (RDM 4) 4 17 9 10 11 12 13 14 18 6 21 2 19 20 8 Insert and Eject Disc Insert a disc, label-side up, with the unit turned on. “Cd” will display on the LCD and then unit will play the first track on the disc. Press the eject button (2) to stop disc play and eject the disc.
JCD2010 SPECIFICATIONS TROUBLESHOOTING CD Signal to Noise Ratio. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . > 70dB Sampling Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44.1Khz Quantization Bits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 bit Frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ASA Electronics Corporation www.asaelectronics.com www.jensenrvdirect.com ©2010 ASA Electronics Corporation v.