WARMING DRAWER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hunt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.
INSTALLATION REQUIREMENTS Roods cans Posts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. Tools needed Phillips screwdriver Flat-blade screwdriver Measuring tape Level Drill 194" {3.5 om) hole saw Parts supplied wm Two #8-18 x 1%" screws w Lens {for panel ready models) Check local codes. Check existing electrical supply. See “Electrical Requirements.
Clearance Dimensions Front view 120 volt grounded outlet {or located in adjacent cabinet) i — ren, |B. 1 8 warming | ¢ | drawer x out WARMING MINIMUM CUTOUT MINIMUM/ CUTOUT MINIMUM DRAWER SIZE BETWEEN HEIGHT (B) RECOMMENDED (C} WIDTH (D} CABINET CUTOUTS (A) WIDTH (E} 27° (68.6 cm) 2 (dom) 9% @32om) 10 (2.5comy 25% (64.8 0m) 27° (68.6 my 444" (10.8 omy} 30° (76.2 omy 21%" (6.4 omy Gu 232cmy 1" 25cm 28%" (724 cry 30° (76.2 cm) 4%" (10.
Clearance Dimensions Flush Installation Front View Side View Cabinet Back F Top View pita E D Hy less Cleats “ 0 44.1 om) bg 27° Models 30° Models A Width of flush inset cutout (minimum) 2716 (89.2 orn) 30" (76.8 amy B Height between cutouts {minimum} 2%" {6.4 cm) 272" (6.4 cm} C Height of flush inset cutout (minimum) 10%” (27.3 om) 10%” (27.3 om} bo Battalion of cutout to floor (recommended) 8%4° (21.0 emy 84" (21.0 cmy Bottom of cutout to floor (minimum) 5" (12.7 om) 5" (12.
od Baptizer A copy of the above code standards can be obtained from: National Fire Protection Association 1 Battery march Park Quincy, MA 02169-7471 CSA International 8501 East Pleasant Valley Road Cleveland, OH 44131-8575 wm A120 volt, 60 Hz, AC only, 18-amp fused, electrical circuit is required, A time-delay fuse or circuit breaker is also Electrical Shock Hazard recommended. [tis recommended that a separate circuit serving only this warming drawer be provided.
. Use the two #8-18 x 12" screws provided to secure the warming drawer frame to the cabinet. A Two #8-18 x 15" screws 1. Check that all parts are now installed. if there is an extra part, go back through the steps to see which step was skipped. Check that you have all of your tools, Dispose off recycle all packaging materials. For warming drawer use and cleaning, read the Use and Care Guide.
3. It is recommended that if a wood or porous custom drawer front is installed. a high quality spray polyurethane finish be applied to the inner wood surface. For the lens, drill a ¥46" {7.9 mim} diameter hole through the appearance side of the custom drawer front. This hole will allow the On Indicator Light to be visible through the custom drawer front. To secure the lens, use an adhesive specified for plastic fo wood application. install custom handle (not supplied) through custom drawer front. 8.
SÉCURITÉ DU tiroir-caisse Votre sécurité et celle des autres est trais importante. Nous donnas de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de toujours lire tous les messages de sécurité et de vous y conformer.
EXIGENCES D’INSTALLATION iF ps Cnt see pelas Rassembler les outils et pièces nécessaires avant d'entreprendre Installation. Lire et observer les instructions fournies avec chacun des outils de la liste cl-dessous. Outils nécessaires Tournevis Phillips Tournevis a lame plate Maure ruban Niveau Perceuse Scie-cloche de 1%" (3,5 cm) Piges fournies wm Deux visn® 8 de 18x 1%" wm Cabochon (pour les modelés avec panneaux prêts-a-installer) Consulter les codes locaux. Vérifier I'alimentation électrique existant.
Dimensions d’espacement Vue de face Prise de 126V ridelle 4 la terre {ou} situe sang un placard adjacent} Ouvertures § décapées rE pour fe tires ¥ réchaud Bg B Plinthe TAILLE BU DISTANCE HAUTEUR DE DISTANCE LARGEUR BE LARGEUR TIROIR MINIMALE L'OUVERTURE (B) MINIMALE/ L'OUVERTURE (D} MINIMALE RÉCHAUD ENTRE LES RECOMMANDÉE (C) DU PLACARD (E) OUVERTURES (8) SI EEE em) ave 6.4 om BT 232 omy TEE my TE (B48 am) ZT IB6.6 om 435 (10,6 om) EE) 91%" 23,2 om) 2.5 omy 281% (72,4 om) 30" 76.
Dimensions d’espacement pour une installation en affleurement Yue de face A w Tasseaux abrasion Vue latérale Arrière de i caisse Vue de dessus E Asseau latéral 810m tg f Modelés de 27° Modelés de 30“ Largeur minimale de l'ouverture intégrée en affleurement 27%" (69.2 omy 3074" (76.8 cm) Hauteur minimale entre les ouvertures 212" (8,4 cm) 212" (6.4 cm) Hauteur minimale de "ouverture intégrée en affleurement 10%" (27,3 cm) 10%" (27,3 cm) Distance recommandée du fond de I'ouverture au sol 814" (21.
Risque de choc électrique Brancher sur une prise & 3 alvéoles reliée & la terre. Ne pas enlever la broche de Saison & la terre. Ne pas utiliser un adaptateur., Ne pas utiliser un câble de rallonge. Le non-respect de ces instructions peut causer un décès, un incendie ou un choc électrique.
7. Utiliser les deux vis n° 8-18 x %" fournies pour fixer le cadre du tiroir-réchaud sur le placard. A A Deux vis n° 8-18 x %* fon 1. Héritier que toutes les pièces sont maintenant installées. 8H reste une place, passer en revue les différentes étapes pour découvrir laquelle aurait été oubliée. 2. Vérifier la présence de tous les outils. Jeter/recycler tous les matériaux d'emballage. Pour 'utilisation et le nettoyage du tiroir-réchaud, lire le Guide d'utilisation et d'entretien.
3. 4 1 est recommandé d'appliquer une finition en polyuréthane {vernis yacht) de première qualité sur la surface en bois intérieure, si une façade de tiroir personnalisé poreuse ou en bois est installée. Pour te cabochon, percer un trou de %s" (7,9 mm) de diamètre 4 travers le coté apparent de la façade du tiroir personnalisé. Ce trou permettra de visualiser le témoin lumineux “ON” {en marche) a travers la façade du tiroir personnalisé.