User Manual

ManualsBrandsJeckson Electric ManualsElectronicsTranceiver Module

Owner's Manual

WIRELESS REMOTE SWITCH

MODEL: 47-1012E-R

FCC ID: ELY547-47-1012E-R IC 1492A-471012ER

FLAME/HEAT ON/OFF BUTTON

Press the Flame/Heat On/Off button to turn the Flame/Heat function ON or OFF. When the heater

function is ON, the icon is displayed on the remote control in the upper left hand corner. When this icon

is displayed, the red indicator light is activated on the firebox.

NOTE

When using the remote control the heater runs on a thermostat. Press the or direction keys to adjust

the set temperature. Once the desired set temperature is reached the heater will turn OFF. The heater

will cycle ON and OFF to maintain the desired set temperature.

PURIFIRE ON/OFF BUTTON

Press the Purifire™ On/Off button to turn the Purifire™ function ON or OFF. When the Purifire™

function is ON and the Heater icon is NOT displayed on the remote control, the green indicator light is

activated on the firebox.

NOTE

To turn the Flame/Heat and Purifire™ ON or OFF at the same time, press both control buttons

simultaneously.

DIMMER

Press the left “-“ or right “+” direction button to decrease or increase the brightness of the upper lights.

NOTE

The bar graph located on the display screen indicates the upper light brightness range.

FLAME SPEED

Press the left “-“ or right “+” direction buttons to decrease or increase the flame speed.

NOTE

The bar graph located on the display screen indicates the speed range of the flame.

Summary of content (6 pages)

PAGE 1
Owner's Manual WIRELESS REMOTE SWITCH MODEL: 47-1012E-R FCC ID: ELY547-47-1012E-R IC 1492A-471012ER FLAME/HEAT ON/OFF BUTTON Press the Flame/Heat On/Off button to turn the Flame/Heat function ON or OFF. When the heater function is ON, the icon is displayed on the remote control in the upper left hand corner. When this icon is displayed, the red indicator light is activated on the firebox. NOTE When using the remote control the heater runs on a thermostat.
PAGE 2
COUNTDOWN TIMER To set the Countdown timer, press the left “-“ or right “+” direction buttons to decrease or increase by 30 minute decrements or increments. The countdown timer can be set from 30 minutes to 8 hours. The fireplace will automatically turn OFF when the sleep timer reaches 0 minutes. PURIFIRE SPEED The Purifire™ includes a high efficiency filter to help improve the quality of air. When the Purifire™ function is ON, the green indicator light is activated on the firebox.
PAGE 3
INITIALIZING THE REMOTE CONTROL 1. Plug cord into 120 volt wall outlet. 2. Set the 3 position manual control to Position 1 (left position). 3. Press and hold the initialization button on the Switch Power. 4. While holding the initialization button, press the flame ON/OFF button button or the Purifire™ ON/OFF on the remote control transmitter. 5. Release the initialization button on the Switch Board. The remote control is now ready for operation. Switch Board Panel CAUTION 1.
PAGE 4
WARNING! This OEM module is to be installed only in Dimplex North America Limited end products by Dimplex North America Limited personnel, and shall not be offered to 3rd party OEM integrators or the general public. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PAGE 5
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
PAGE 6
Installation Locate and insert the plug connectors on the remote control (PCBA) into plug connectors on the fireplace. 2. Lock the PCBA by the 4 stand-offs on the fireplace. 1.