Installation Instructions

ManualsBrandsJCM Technologies ManualsElectronicsTransmitter for automatic door safety edges

COD. 1248034-GB / 1.1

RBAND/OS – RBAND/OSB

- 1 -

• INTRODUCTION

DESCRIPTION

The RadioBand system is designed of Industrial, Commercial and Domestic door and gate applications where a safety edge

is used. The system provides a wireless system replacing spiral cables or energy chain systems to provide the safety signal to

the door or gate control panel. The receiver monitors the status of transmitters connected to it.

Up to three transmitters per output can be connected to the receiver. There are two outputs on each receiver. The system is

compatible with 8K2 monitored safety edges, opto safety edges and volt free safety contacts. Two inputs available in the

transmitter.

The system complies with EN ISO 13849-1.

USE OF THE SYSTEM

This equipment is designed to be installed with a safety edge for door and gate installations. It is not guaranteed for directly

activating equipment other than that specified.

The manufacturer reserves the right to change the specification of the equipment without prior warning.

• RBAND/O TECHNICAL CHARACTERISTICS

System non compatible with RADIOBAND 1G.

RBAND/OS – RBAND/OSB

Frequency Multifrequency system (433 MHz,

868 MHz)

Power supply 3V DC (2 x 1.5V LR6 AA)

Operating consumption 10mA

Radiated power < 25mW

Operating temperature -20ºC - +85ºC

Watertighness IP65

Size 151x60x23mm

Range 10 metres

Battery life (aprox) 2 years

Summary of content (8 pages)

PAGE 1
COD. 1248034-GB / 1.1 RBAND/OS – RBAND/OSB • INTRODUCTION DESCRIPTION The RadioBand system is designed of Industrial, Commercial and Domestic door and gate applications where a safety edge is used. The system provides a wireless system replacing spiral cables or energy chain systems to provide the safety signal to the door or gate control panel. The receiver monitors the status of transmitters connected to it. Up to three transmitters per output can be connected to the receiver.
PAGE 2
COD. 1248034-GB / 1.1 RBAND/OS – RBAND/OSB • INSTALLATION PROCEDURE AND BASIC WIRING MECHANICAL INSTALLATION Fix the back of the box to the door. Install the transmitter following the technical manual and avoid placing metallic surfaces between the receiver and the transmitter. Pass the cables through the bottom of the transmitter. Connect the safety edge following the electrical connections clause and ensure that the safety edge keeps totally waterproof.
PAGE 3
COD. 1248034-GB / 1.1 RBAND/OS – RBAND/OSB The activation time of the opto safety edge can be modified. Before doing this operation it is necessary to know the door travel time. 1. Press the receiver PROG and CHECK buttons simultaneously until the three CHECK, B1 and B2 leds go light on. 2. Press the PROG button to begin the memorisation of the time the opto safety edge will be activated. You will hear a beep each second, to count the time easier. 3.
PAGE 4
COD. 1248034-GB / 1.1 RBAND/OS – RBAND/OSB CONNECTING AN AUXILIARY INPUT When programming in the receiver the Mode 4 (See PROGRAMMATION clause), an auxiliary input turns available on the transmitter. The transmitter transmits the status of auxiliary input to the second relay of the receiver. This auxiliary input is a normally open contact and it will be programmed always in the relay 2 of the receiver.
PAGE 5
COD. 1248034-GB / 1.
PAGE 6
COD. 1248034-GB / 1.1 RBAND/OS – RBAND/OSB • PROGRAMMATION Each safety edge transmitter must be learnt into the appropriate channel of the safety edge receiver. Mode 1 2 3 4 Configuration of transmitter programming in the receiver.
PAGE 7
COD. 1248034-GB / 1.1 RBAND/OS – RBAND/OSB If 10 seconds pass without programming a transmitter, the receiver will exit the programming mode. If when programming a transmitter the receiver’s memory is full then it will emit 7 beeps of 0.5 sec and exit the programming mode. • MAINTENANCE TRANSMITTER BATTERY LOW INDICATOR If the battery of a transmitter programmed into the receiver becomes low, the receiver will beep 4 times every 20 seconds.
PAGE 8
COD. 1248034-GB / 1.1 RBAND/OS – RBAND/OSB IMPORTANT ANNEX Disconnect the power supply whenever you proceed to the installation or repair of the control panel. In accordance with the European low voltage directive, you are informed of the following requirements: · For permanently connected equipment, an easily accessible connection device must be incorporated into the cabling.