Installation Instructions

ManualsBrandsJCM TECHNOLOGIES ManualsElectronicsSafety edge wireless receiver

Miller Edge, Inc. • www.milleredge.com • info@milleredge.com • East Coast: 800-220-4422 • West Coast: 800-887-3343

INSTALLATION INSTRUCTIONS

Model: RB-P-K10

IMPORTANT: READ AND UNDERSTAND ALL

INSTRUCTIONS BEFORE BEGINNING INSTALLATION

The Miller Edge RBand Monitored Door Edge Transmitter/Receiver system is intended to provide a wireless

connection between a monitored sensing edge and a motorized operator installed with a garage door or grille.

RBand meets the 2016 UL 325 requirements for monitored devices and has been certiﬁed as a UL 325 Recognized

Component. It is designed for use with operators that comply with 2016 UL 325 using a Miller Edge 10K Sensing

Edge.

1. PARTS LIST

Kit Contents:

1. RBand Edge Transmitter (RB-TX10C)

2. RBand Door Edge Receiver (RB-P-RX10C)

3. (2) 3.6V AA lithium batteries*

4. (4) #6 pan head transmitter mounting screws

*Replacement 3.6V AA lithium batteries can be

purchased at your local electronics store or via

Miller Edge.

Required:

• 1/8” ﬂat blade screwdriver

• 1/4” ﬂat blade screwdriver

• Miller Edge 10K (T2/blue band) Sensing Edge

Recommended:

•

Multi-meter capable of reading 10KΩ

• Mounting screws as required for receiver

2. RECEIVER INSTALLATION

2-1. Turn off power to the door operator.

2-2. Remove Receiver cover and mount the receiver base near the operator, where it will be in line of sight with

the transmitter for the entire range of travel [IMAGE 1].

2-3. Connect power (12-24 VAC/DC) to the terminals marked power, noting the +/- polarity. 24 VAC power can

be connected either way not polarity sensitive [IMAGE 2].

2-4. Connect both OSE1_2FA and OSE1_2FB to the photo-eye inputs on the operator. OSE1_3F is not used.

2-5. Replace the Receiver cover and turn on power to the operator. Note: it takes ~5 seconds for the Receiver to

initialize.

Note: RBand 10K Door Edge Receiver is compatible with up to 3 RBand Transmitters.

RBAND

MONITORED DOOR EDGE TRANSMITTER/RECEIVER

RB-P-K10_Install_20200115

IMAGE 1. Door Installation with RBand Transmitter & Receiver

OPERATOR

RBAND RECEIVER

MOUNTED BELOW OPERATOR

WITH ANTENNA POINTED DOWN

ANTENNA

WIRING

RBAND TRANSMITTER

MOUNTED ABOVE

SENSING EDGE

SENSING

EDGE

DRAFT

Summary of content (4 pages)

PAGE 1
RBAND INSTALLATION INSTRUCTIONS Model: RB-P-K10 MONITORED DOOR EDGE TRANSMITTER/RECEIVER IMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION R AF T The Miller Edge RBand Monitored Door Edge Transmitter/Receiver system is intended to provide a wireless connection between a monitored sensing edge and a motorized operator installed with a garage door or grille. RBand meets the 2016 UL 325 requirements for monitored devices and has been certified as a UL 325 Recognized Component.
PAGE 2
LED INDICATORS Initial Power • No Transmitters Programmed: R1 LED on ANTENNA R1 LED (1 edge connected) • Programmed: Off • Fault Condition: On ANTENNA TERMINAL BLOCK CHECK LED & BUTTON AF T Check LED • Programmed: Check LED flashes every 5 seconds R2 LED • Not used RELAY LEDS PROGRAM BUTTON DIP SWITCH SETTINGS ON 1 2 3 GND ANT CHECK Leave switches in factory default settings (all on).
PAGE 3
PROGRAM BUTTON (2) 3.6V AA LITHIUM BATTERIES GREEN LED ALIGNMENT PIN ALIGNMENT PIN REMOVABLE SENSING EDGE TERMINAL BLOCK (4) CORNER MOUNTING HOLES R AF T STRAIN RELIEF FITTING IMAGE 3. RBand Edge Transmitter PCB & Connections 3. TRANSMITTER: PROGRAM MODE 3-1. Confirm the Receiver is powered up. Prior to mounting the Transmitter, remove the cover and insert the batteries, noting their polarity [IMAGE 3].
PAGE 4
7. TRANSMITTER: SPECIFICATIONS & CONTROLS Transmitter Frequency: 916 MHz, FSK modulation TX Indicator Lights: • Green LED: Normally off • Press program button for status Mounting: 4 corner screws (provided) Power Source: Batteries: 2 AA, 3.6V lithium, 2 year life expectancy Dimensions: 1.80”L x 4.78”W x 1.75”H Program Button: Momentary push button is used to associate the Transmitter to the Receiver. 8. RECEIVER: SPECIFICATIONS & CONTROLS 9.