Installation Guide

ManualsBrandsJCM Technologies ManualsElectronicsTransceiver for Automatic Door Safety Edges OSE Output

www.milleredge.com info@milleredge.com 800-220-3343

IMPORTANT: READ AND UNDERSTAND ALL

INSTRUCTIONS BEFORE BEGINNING INSTALLATION

The Miller Edge RBand Monitored Door Edge Transmitter/Receiver system is intended to provide a wireless

connection between a monitored sensing edge and a motorized operator installed with a garage door or grille.

RBand meets the 2016 UL 325 requirements for monitored devices and has been certiﬁed as a UL 325 Recognized

Component. It is designed for use with operators that comply with 2016 UL 325 using a Miller Edge 10K Sensing

Edge.

1. PARTS LIST

Kit Contents:

1. RBand Edge Transmitter (RB-TX10)

2. RBand Door Edge Receiver (RB-D-RX10)

3. (2) 3.6V AA lithium batteries*

4. (4) #6 pan head transmitter mounting screws

*Replacement 3.6V AA lithium batteries can be

purchased at your local electronics store or via

Miller Edge.

Required:

• 1/8” ﬂat blade screwdriver

• 1/4” ﬂat blade screwdriver

• Miller Edge 10K (T2/blue band) Sensing Edge

Recommended:

• Multi-meter capable of reading 10KΩ

• Mounting screws as required for Receiver

2. RECEIVER INSTALLATION

2-1. Turn off power to the door operator.

2-2. Remove Receiver cover and mount the Receiver base

near the operator, where it will be in line of sight with the

Transmitter for the entire range of travel [IMAGE 1].

2-3. Connect power (12-24 VAC/DC) to the terminals marked

power, noting the +/- polarity. 24 VAC power can be

connected either way not polarity sensitive [IMAGE 2].

2-4. Connect wiring from the C1 and BS1 terminals on the

Receiver to the 10K monitored input terminals on the

operator (not polarity sensitive).

2-5. Replace the Receiver cover and turn on power to the

operator. Note: it takes ~5 seconds for the Receiver to

initialize.

Note: RBand 10K Door Edge Receiver is compatible with

up to 3 RBand Transmitters.

RB-D-K10-C_Install_A4_20170706

IMAGE 1. Door Installation with

RBand Transmitter & Receiver

INSTALLATION INSTRUCTIONS

Model: RB-D-K10

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS Model: RB-D-K10 IMPORTANT: READ AND UNDERSTAND ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION The Miller Edge RBand Monitored Door Edge Transmitter/Receiver system is intended to provide a wireless connection between a monitored sensing edge and a motorized operator installed with a garage door or grille. RBand meets the 2016 UL 325 requirements for monitored devices and has been certified as a UL 325 Recognized Component.
PAGE 2
LED INDICATORS ANTENNA Initial Power • No Transmitters Programmed: R1 & R2 LEDs on R1 or R2 LED • Programmed: Off • Fault Condition: On R3 LED • On when battery is low A TEST LED • On in test mode CHECK LED & BUTTON ANTENNA TERMINAL BLOCK RELAY LEDS PROGRAM BUTTON CHECK LED (both channels programed) • Programmed: Check LED flashes every 5 seconds DIP SWITCH SETTINGS ON 1 2 3 4 GND ANT CHECK Switch 1-4: Leave switches in factory default settings PROG R1 R2 MR ON 1 2 3 4 R3 A TEST TABLE 1.
PAGE 3
PROGRAM BUTTON (2) 3.6V AA LITHIUM BATTERIES GREEN LED ALIGNMENT PIN ALIGNMENT PIN REMOVABLE SENSING EDGE TERMINAL BLOCK (4) CORNER MOUNTING HOLES STRAIN RELIEF FITTING IMAGE 3. RBand Edge Transmitter PCB & Connections 3. TRANSMITTER: PROGRAM MODE 3-1. Confirm the Receiver is powered up. Prior to mounting the Transmitter, remove the cover and insert the batteries, noting their polarity.
PAGE 4
7. RECEIVER: SPECIFICATIONS & CONTROLS (cont.) Power: 12-24 VAC/DC nominal (11-30 V max); 100 mA max current draw. Power may be supplied from the operator or alternatively from an external supply. Dimensions: 4.12”L x 3.65”W x 1.