02/08/07 14:07 Side 1 English 34199_Control_2_4G_Eng ® JBL ON AIR ® CONTROL® 2.
34199_Control_2_4G_Eng 02/08/07 14:07 Side 2 FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
02/08/07 14:07 Side 3 English 34199_Control_2_4G_Eng READ FIRST! Important Safety Precautions! 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8.
34199_Control_2_4G_Eng 02/08/07 14:07 Side 4 THANK YOU FOR CHOOSING JBL For more than 60 years, JBL has been involved in every aspect of music and film recording and reproduction, from live performances to the recordings you play in your home, car or office. We’re confident that the JBL system you have chosen will provide every note of enjoyment that you expected – and that when you think about purchasing additional audio equipment for your home, car or office, you will once again choose JBL.
02/08/07 14:07 Side 5 English 34199_Control_2_4G_Eng CONNECTIONS Notes: For the sake of simplicity, throughout this manual we have used the term “source” when describing connections and operation. This would apply to any device such as an A/V receiver, audio component, computer or portable music player. Step 2. Determine the location of the surround speakers. Subwoofer The JBL On Air Control 2.4G is designed for use in most countries worldwide, depending upon local regulations.
34199_Control_2_4G_Eng 02/08/07 14:07 Side 6 Step 3. Connect the speaker wire (included) to the push terminals on the active speaker 5 and the push terminals on the rear of the passive speaker 9. See Figure 3. Please note that the speaker wire supplied features a polarity stripe to help distinguish its two conductors. Use this polarity stripe to ensure that you are connecting the positive (+) terminal on one speaker to the positive (+) terminal on the other, and the negative (–) to the negative (–).
02/08/07 14:07 Side 7 English 34199_Control_2_4G_Eng When connected properly, the top LED on the front of the active speaker should be green. When first plugged in, it will sometimes take several seconds for the Control 2.4G active speaker to initialize and “wake up.” Until then, the top LED will be in red. Once the top LED is green, the bottom LED should flash green until the transmitter and active speaker “lock in.” It will then also light in solid green.
34199_Control_2_4G_Eng 02/08/07 14:07 Side 8 OPERATION Adjusting the Volume Application 1 Adding surround speakers to a home theater system: In this application, the output level of your Control 2.4G active speakers will not only be dependent on the volume setting of your A/V source, it will also need to be properly adjusted after installation and before use in order to be able to work correctly with the other speakers in your multichannel surround system.
02/08/07 14:07 Side 9 English 34199_Control_2_4G_Eng WALL AND STAND PLACEMENT Adjustable wall brackets are included for the two speakers and transmitter module. The included bracket are for wall-mounting only. It is not to be used for ceiling mounting. Ceiling mounting of the Control 2.4G transmitter and/or speakers is not recommended, regardless of bracket used. A. Loosen and remove the molded nut (2) by turning it counter clockwise.
34199_Control_2_4G_Eng 02/08/07 14:07 Side 10 Wall-Mounting the Speakers Using Third-Party Wall Brackets Each JBL On Air Control 2.4G wireless speaker contains a 1/4"-20 threaded insert on the back to facilitate the use of third-party wall brackets. Please consult your JBL dealer or distributor for recommendations. NOTES: Customer is responsible for proper selection and installation of appropriate third-party wall brackets.
02/08/07 14:07 Side 11 English 34199_Control_2_4G_Eng SPECIFICATIONS Frequency Range (±3dB): 80Hz – 20kHz Amplifier Output: 15 Watts per channel Low-Frequency Driver: 100mm (4") Magnetically shielded High-Frequency Driver: 12mm (1/2") Titanium-laminate, magnetically shielded Operating Range: Up to 21m (70') depending upon conditions RF Operating Frequency: 2.
34199_Control_2_4G_Eng 02/08/07 14:07 Side 12 JBL and Control Series are trademarks of Harman International Industries, Incorporated, registered in the United States and/or other countries. Pro Sound Comes Home are trademark of Harman International Industries, Incorporated. PRO SOUND COMES HOME™ ® Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, NY 11797, USA 8500 Balboa Boulevard, Northridge, CA 91329, USA 2, route de Tours, 72500 Château du Loir, France 516.255.
