JAY’S AUDIO CDT2-MK2 USER MANUAL WWW.JAYS-AUDIO.
QUICK START GUIDE 1. After receiving the CDT, please do not rush to power it up. First, check the physical appearance of any damage may be caused by shipping. 2. Slide the top loading lid open and remove the protection foams completely. 3. Insert a disc, put on disc clamp, close the slider lid. You should hear a click sound where the slider lid limit switch triggered. 4. Plug in the power cord and turn on the rear power switch. 5.
INTRODUCTION Jay’s Audio products are built with performance and durability in mind. Each product is tested carefully with Audio Precision APX525 before shipping. Careful installation of the product will ensure the correct performance and ensure the product is at its full potential. PACKAGE CONTENTS 1. 2. 3. 4. 5. 6. AC Mains Power Cord Disc Clamp Gloves Remote Control Unit Spare Fuse CDT2-MK2 UNPACKING The CDT is shipped with sturdy double boxes.
CONNECTIONS The connections of power cord, interconnect cables are located at the rear panel of the CDT. For both safety and performance, please use quality cable from reputable suppliers. i.e. Studio Grade cable, namely, Gotham / Sommercable / Mogami / Belden, etc. 1 3 2 Figure 1. CDT2-MK2 Rear Panel (1) AC MAINS POWER SWITCH Switch On/Off the unit by using the power switch. 0 denotes Off, 1 denotes On. There is no standby function.
The Digital Outputs are isolated. You may connect more than one output to the external DACs. Should you need to run a long interconnect cable, we recommend ASE/EBU connection. HDMI I2S (LVDS) Figure 2. HDMI I2S Pinout There is no industry standard of I2S connection. We could not guarantee the I2S connection workability with your DAC. This shall not be considered as a defect should the matching failed.
OPERATION Figure 3. CDT2-MK2 Top Loading Disc Loading To open the CDT2-MK2 top loading door, slide the lid towards the rear of the unit fully. The CDM4 assembly shall be visible, and the Disc Clamp shall be accessible. Lift the Disc Clamp gently by holding the centre part of the Disc Clamp. Place a disc to the centre of the disc holder. Place the Disc Clamp in the centre of the disc and disc holder.
Playback Turn on the rear power switch. After about 5 seconds of spinning the disc, the CDT automatically enters power-on state, and the OLED display flashes “READ” indicating that the disk information is being read. After the disc information is correctly retrieved, the disc information’s will be displayed. For example, "18 84:18". At this point, the CDT is in normal operation. Hit the Play button on the front panel to start playing the tracks.
REMOTE CONTROL UNIT The CDT2-MK2 comes with a milled solid aluminium Remote Control Unit. It is a generic Remote Control equipped for all CDT/CDP products; hence, it is not all the buttons are functional with the CDT2-MK2.
DESIGN HIGHLIGHT PHILIPS CDM4/19 Mechanism SCHURTER IEC Inlet Improved Noise Filter with 110v/230v switching NORATEL Encapsulated Transformers Multistage Super Regulator with Japan Nichicon Gold Tune Caps CRYSTEK FEMTO Clock HDMI I2S LVDS Output Scientific Digital Output Isolation Transformer Full CNC Milled Aluminium Chassis Figure 5. Internal of CDT2-MK2 * Premium components available exclusively at flagship store only WWW.JAYS-AUDIO.
SPECIFICAITON Digital Output o Output Sampling Rate 16 Bit / 44.1KHz o COAX (RCA/BNC) 2Vrms, 75ohm o AES/EBU 5Vrms, 110ohm o HDMI I2S LVDS AC Power: 110V/230V Power Consumption: 20W Dimension: 430mm x 380mm x 120mm Weight: 15KG Warranty: 12 months WWW.JAYS-AUDIO.