von-STD Manual Instruction
Cautions For Safety We kindly recommend you to be fully aware of using a product accurately and for safety of user. All liabilities by uncomplying cautions are not supposed to be responsible to manufacturer. 1 This product into water or prolonged exposure to moisture can cause failure resulting in no charge for broken A/S 1. A/S. 2. Do not disassemble or repair this product if the label seal is broken or damaged, free A/S will not be received. 3.
1. von-STD Descriptions 1.1 Overview V Von-STD STD as vehicle hi l driving di i llogs ttracker k designed d i d to t collect ll t a vehicle hi l driving di i information i f ti ffrom ECU(El ECU(Electronic t i Control C t l Unit) U it) By OBD standard protocol communication and can be saved a driving logs by connecting to PC.
1. von-STD Descriptions 1.2 Specifications 4 In-vehicle Protocol ISO 9141-2, ISO 14230-4(KWP-2000), ISO15765-4(CAN) J1850(PVM/VPW) protocol supported, physical communication standard followed and high credibility being with vehicle DB. 32 bit main processor Boasting fast and stable performance ARMv7 Cortex-M3 CPU has adopted.
1. von-STD Descriptions 1 3 Functions 1.3 Saving vehicle information. Collecting and saving driving logs information.
1. von-STD Descriptions 1.4 Specification Specification CPU 32 bit bi ARMv7 ARM 7 Cortex-M3 C M3 Memory 4 MB Internal Flash Memory LED Display LED External interface specification USB USB 1.1(2.0 1 1(2 0 Compatible) C ibl ) VCP(Virtual COM Port) Supported Bluetooth v2.0 Class 1 CAN[Control Area Network]: ISO 11898 / Vehicle protocol Bluetooth 2.4GHz ISM band (JTBT1100) F Frequency range: 2,400 2 400 ~ 2,483.
1. von-STD Descriptions 1.4 Composition Name 7 Function OBD II module (body) Connection to vehicle OBD II connector. USB cable Use for uploading the driving logs data by PC connection. Quick Start Manual Quick guide manual Program installation CD von-S von S PC Manager installation program, included in user user’ss manual.
1. von-STD Descriptions 1.5 Body description 8 Front display LED Red/Blue/White display LED OBD connector Connect to vehicle OBD diagnostic port with SAE J1962 OBD-II 16Pin standard connector.
2. Product Instructions 2 1 OBD II module installation 2.1 OBD II module installation is following below order. 1. OBD II module installation requires after vehicle parking in safety area. ** Caution : A side brake or foot brake should be locked and shift also checked on the parking position. 9 2. Please check vehicle engine should be off when if ignition on 3. Check the position of vehicle OBD diagnostic connector.
2. Product Instructions 2 1 OBD II module installation 2.1 OBD II module installation is following below order. 4. Connect vehicle OBD diagnostic connector and OBD II module connector. 5. Green LED of OBD II module will be blinked every 1 second. 6. Red or Green LED lamp will be continually blinked within 1 minute after ignition on. 7. After checking normal installation, green LED lamp blinks every 1 second after ignition off and All LED lamps will be turn off later [saving mode] 2.
2. Product Instructions 2.3 OBD II module separation ** Caution : OBD II module separation should be performed at safety area after parking. ** Caution : The separation from vehicle is prohibited if not the purpose of driving data saving or transmitting. ** Caution C ti :P Performing f i OBD II module d l separation ti on iignition iti on may b be caused d tto d data t lloss or module d l d damaged. d 1. 2. 11 Turn vehicle ignition off.
2. Product Instructions 2 4 Driving log data saving and transmitting 2.4 1. Preparation 1) PC manager program needs to install to save the driving logs data recorded from OBD II module. * Tip : A program installation manual is available [3. PC Manager installation manual(31~34 page)] 2) Please separate OBD II module from vehicle. [2.6 module separation (21 page)] ** Caution : Vehicle data on the status of connecting to vehicle can not be transmitted by USB cable.
3. Warranty & After Sale Service 3.1 Before A/S request service **Caution : Driving logs data should be saved certainly in advance for A/S request if a product’s defect checked. 13 Power and LED status off Check OBD II module and 16 pin connector connection status. status Not connected to PC Check PC USB port and OBD II module connection status and PC USB port status.
3. Warranty & After Sale Service 3.2 Warranty Service 1. Warranty Period : 1 year 2. Warranty Details 1) Any defective or damage within warranty period can be repaired free A/S service or exchanged as free of charge. 2 Any damage 2) d or defective d f i b by customer’s ’ misuse i iis not allowed ll d ffree exchange h or ffree charged h d A/S S service. i 3. Exchange and Return 1) An exchange or return is possible within 1 week after purchase if not opening box.
FCC ID : UK4JTBT2100 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications (including the antennas) made to this device that are not expressly approved by the manufacturer may void the user's authority to operate the equipment.
