Chapter 2 START THE BASIC OPERATION Chapter 2 START THE BASIC OPERATION When * basic adjustment is made by the serviceman etc. beforehand, please perform as it is. (In case of no adjustment is done by the serviceman etc. beforehand, please through eyes to Chapter 5 for the time being, and after getting to know the outline of operation of this radar, perform Initial setting of Chapter 7.) The screen is a touch screen and can be operated by tracing a screen by a finger flip or touching.
Chapter 2 START THE BASIC OPERATION Power on startup screen. Push PWR/CLR button. Startup screen. (3 Startup screen possible to select.) Swipe on the screen for select the startup screen.
Chapter 2 START THE BASIC OPERATION Rotary knob. Push Rotary knob and rotate to select the starting item.. Select the icon you needed by turning the knob Tap icon at bottm side, then full icons can be seen. Full icons will be appeared. Keep press and rotate the rotary knob, then screen brillance menu will be open. The turn while pressing Brillance menu will be appeared. Rotate Rotary knob at suitanble brilliande level.
Chapter 2 START THE BASIC OPERATION Sleep Cursor Tap Sleep TX/STBY Tap TX/STBY Tap TX/STBY Activate Cursor Tap Activate TX/STBY After a few seconds, the icons fade out. Push or click the Rotary knob.
Chapter 2 START THE BASIC OPERATION 2 - 1 G UI D E F OR O P E R A TI ON Front view Multi-Touch screen. ☆ Operate using “tap” “flick” long tap” “swipe” by fingertip. Rotary knob. ☆ Rotation: select the sequential menu. ☆ Push or click fix menu data. POWER ON OFF, CLEAR PUSH BUTTON. ☆ POWER ON/OFF ☆ CLEAR OF MENU 2 - 2 P O W ER O N ( S T A N D B Y F O R TR A N SMI T) PRESS PWR / BUTTON Startup screen Start to display screen.
Chapter 2 START THE BASIC OPERATION 2 - 3 DI S P L A Y S C R E EN 2-3-1 SCREEN LAYOUT Course Speed (through ground) Own ship. Range Longitude/Latitude. depth. Range interval Own ship position mark. Alarm Speaker USB Port 34 POWER ON OFF,CLEAR PUSH BUTTON. Push Rotary knob, then appears some menu. ☆ POWER ON/OFF Rotation of Rotary knob can select menu of activated icon. ☆ CLEAR OF MENU Function call icon will be displayed.
Chapter 2 START THE BASIC OPERATION Various ST-BY screen. Tap White dot Tap △ Normal ST-BY screen, Normal ST-BY screen, * ST-BY Disp, Select.: Normal ST-BY screen, “Normal” Tap White dot Graphical ST-BY screen * ST-BY Disp, Select.: Course Tap △ Graphical ST-BY screen ”Graphical” Speed Course Tap White dot Numeric Display ST-BY screen. Course Speed Speed Tap △ Own ship position Own ship position * ST-BY Disp, Select.: Graphical ST-BY screen Numeric Display ST-BY screen.
Chapter 2 START THE BASIC OPERATION TX screen. Push Rotary knob, select TX icon by rotating Rotary knob and push Rotary knob. Push Rotary knob & select TX icon by rotating. Set focus to TX icon.
Chapter 2 START THE BASIC OPERATION 2-3-2 ICON’S TABLE The icons which will appear by screen operation.
Chapter 2 START THE BASIC OPERATION Display the function icons. Appear icons after Pushing Rotary knob No operation about 10 second. Push Rotary knob Rotate for icon selection. Selected icon is focused. Push Rotary knob, then appear the setting menu. Set level by Rotary knob or flick bar graph.. Then push Rotary knob, data is fixed.
Chapter 2 START THE BASIC OPERATION Tap TX/STBY icon, or Push rotary knob when TX/STBY icon is focused.
Chapter 2 START THE BASIC OPERATION Tap GAIN Adjust icon, or Push rotary knob when GAIN Adjust icon is focused. The case of ST-BY The case of TX Adjustment Gain Adjustment Gain Bar is appeared Bar is appeared Tap “Auto” of Gain setting mode Tap “Auto” of Gain setting mode Gain is set automatically. Rotate the rotary knob with monitoring green bar. Flick the green bar Or Tap “+” or “-“ Or ※In TX mode, can be adjusted while monitoring the display echo.
Chapter 2 START THE BASIC OPERATION Tap SEA Adjust icon, or Push rotary knob when SEA Adjust icon is focused. Adjustment Bar is appeared Tap “Auto” of SEA setting mode Tap “Auto” of SEA setting mode SEA is set automatically. Rotate the rotary knob with monitoring green bar. Flick the green bar Or Tap “+” or “-“ Or ※Can be adjusted while monitoring the display echo.
Chapter 2 START THE BASIC OPERATION Tap RAIN Adjust icon, or Push rotary knob when RAIN Adjust icon is focused. Adjustment Bar is appeared Tap “Auto” of RAIN setting mode Tap “Auto” of RAIN setting mode RAIN is set automatically. Rotate the rotary knob with monitoring green bar. Flick the green bar Tap “+” or “-“ Or Or ※Can be adjusted while monitoring the display echo.
Chapter 2 START THE BASIC OPERATION 2-3-3 BRIEF EXPLANATION OF ICON’S FUNCTION Brief explanation of each icon. GAIN (gain control) adjustment: Set up the sensitivity of Radar echo.. SEA (sea-clutter rejection) adjustment: Control the sea clutter level near the ship. Long distant echo gain is remaining as it is, and gain is lowered as to short distance. Adjust the target ship is clearly observe and reject the sea clutter on screen as much as possible.
Chapter 2 START THE BASIC OPERATION AIS DATA (when received the AIS signal, the data of MMSI of the vessel which has transmitted, latitude, longitude, a direction of movement, speed, rate of turn, etc. is displayed.) (AIS receiver signal is necessary.) EBL (electronic bearing line) Measure the target direction by using cursor line. VRM (variable range marker) Measure the target distance by using circle line.
Chapter 2 START THE BASIC OPERATION Various system setups. Tap the icon, the adjustment menu will be displayed. Choose the item to set up individually. Code input “0” is setting for service menu. Next User menu Special setting menu for user.
Chapter 2 START THE BASIC OPERATION GUARD ZONE setup Set up the watching area around own-ship. If a target goes into the set-up area, generate the alarm sound or signal.. On the other hand, if a target goes out the set-up area, generate the alarm sound or signal, too. One of both is possible to select. Cursor: A tap is carried out, start, drag and tap off on the target. The position of this cursor is indicated. Various kinds of pointing actions uses this cursor..
Chapter 2 START THE BASIC OPERATION 2 - 4 T R A N SMI T (90 seconds pre-heat time is required for cold start, because of the Magnetron heater.) After 90 seconds, anytime transmitting is possible. . Various ST-BY screen.
Chapter 2 START THE BASIC OPERATION Start by “the tapping white dot” or “the pushing rotary knob” White dot White dot rotary knob “Tap TX/ST-BY icon” or “Select TX/ST-BY icon and push rotary knob”, and then transmitting. TX/ST-BY icon Select TX/ST-BY icon and push rotary knob rotary knob Transmitting screen. No operation of 10 second, small menu will be fade out.
Chapter 2 START THE BASIC OPERATION 2 - 5 L E A V E T H E U S E F U L I C O N O N S C R E EN How to copy icon. Basic icon display. Fixed icon (TX/ST-BY, Gain) User free area of menu icon. Tap UP icon Full icon display icons that can be copied to user free area. Fixed icon (TX/ST-BY, Gain) User free area of menu icon. Tap and hold the icon, Tapped icon is copied to free menu area Up to 4 icons can copy the user free area.
Chapter 2 START THE BASIC OPERATION How to remove icon. Full icon display Basic icon display. Tap and hold the icon, on user free area Tapped icon is removed from free menu area Then the remaining icons are shifted to the left. How to add another icon.
Chapter 2 START THE BASIC OPERATION 2 - 6 F U N C TIO N C A LL B Y S C R E E N T A P Various types of icon. (1) Start function immediately. (2) Move into function setting. (3) Double tap start from resist setting state and open menu. TX, ST-BY Every tap changes TX, ST-BY alternately Change Range tap increase range tap decrease range Or While range icon focused Or Rotate the rotary knob with monitoring range. Or Change brightness by Flick the green belt.
Chapter 2 START THE BASIC OPERATION Screen brightness adjustment Tap the icon, then display Adjust menu. Or Or Rotate the rotary knob with monitoring green bar. Change brightness by Flick the green belt. Tap “+” or “-“ Setting level is displayed down side of each icon. Green bar length is proportion to setting level. Also using Rotary knob is possible to adjust. Keep press on the Rotary knob and turn. Anytime it’s possible to change Keep press on the Rotary knob.
Chapter 3 ADJUST THE RADAR ECHO Chapter 3 ADJUST THE RADAR ECHO ▽ △ 3 - 1 C H A NG E R AN G E tap decrease range tap increase range This picture is selected 1.5 nm range. Outer dashed line shows the maximum observation RANGE range. RANGE RING INTAVAL Gain is easily changed by the tap of increase / decrease icon as shown in the figure below tap increase range tap decrease range Or 1.
Chapter 3 ADJUST THE RADAR ECHO Range scale, NKE-1066 scanner It changes to 0.0625NM 0.125NM 0.25NM 0.5NM .075NM 1NM 1.5NM 2NM 3NM 4NM 6NM 8NM 12NM 16NM 24NM and order. NKE-2044 scanner It changes to 0.0625NM 0.125NM 0.25NM 0.5NM .075NM 1NM 1.5NM 2NM 3NM 4NM 6NM 8NM 12NM 16NM 24NM 32NM 48NM and order. A picture will change on a scale as shown in the following figure, as range changes. The radius of the circle shows the range. Example: Video change 0.0625NM 0.125NM 0.25NM 1.
Chapter 3 ADJUST THE RADAR ECHO 3 - 2 A D J U S T S G AI N ( R AD A R S E N SI TI VI T Y) Radar must be set suitable gain, or can’t use as a radar Adjust while Gain icon focused by tapping or selection of rotary knob icon’s green belt show the adjusted level of GAIN How to change the Gain: See the method of Gain adjustment of Chapter2 Example of echo sensitivity as following echo sensitivity Low 6NM echo sensitivity Middle echo sensitivity 6NM High 6NM If GAIN control is the maximum, noise will
Chapter 3 ADJUST THE RADAR ECHO 3 - 3 A D J U S T S E A ( C L U T TE R C ON T R O L) Radar must be set suitable sea control, or can’t use as a radar Adjust while SEA icon focused by tapping or selection of rotary knob icon’s green belt show the set level of SEA How to change the SEA: See the method of SEA adjustment of Chapter2 SEA Level Low 0.5NM 56 SUITABLE Level 0.
Chapter 3 ADJUST THE RADAR ECHO 3-4 ADJUST RAIN AND SNOW CLUTTER CONTROL Radar must be set suitable rain and snow control, or can’t display the suitable picture. Adjust while RAIN icon focused by tapping or selection of rotary knob icon’s green belt show the set level of RAIN How to change the RAIN: See the method of RAIN adjustment of Chapter2 RAIN Small (usually) 6NM RAIN Excessive (the target of the radius direction becomes small.) clear weather (RAIN 0) (RAIN *).
Chapter 3 ADJUST THE RADAR ECHO 3 - 5 A D J U S T B RI L LI A N C E OF S C R E E N Double TAP of screen can change BRILLANCE of screen. Normal TAP, Flick operations also possible to change screen brilliance. range.
Chapter 3 ADJUST THE RADAR ECHO ****FOR REFERENCE**** **** **** Observing the Radar screen, GANI and SEA control adjustment is essential adjustment. RAIN: Normally set “0”, when light rain or snow, turn proportion to reject rain noise on screen. GAIN: Set the GAIN adjustment for long range (more than 6nm) target can observe clear. Under this conditions, short range near own ship, cannot observe small target because of high clutter and high gain.