User's Manual

ManualsBrandsJapan Radio ManualsElectronicsMarine Radar

JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS

8－33

8.4.4 Replacement of LCD Monitor

8.4.4.1 Display Unit NCD-4990

Do not touch the LCD screen directly with your fingers.

Do not touch the AR filter directly with your fingers.

Perform the replacement work on a soft cloth to avoid damage to the LCD screen and

other parts.

[Required tools]

•

A Phillips screwdriver for 4 mm screws

•

A Phillips screwdriver for 6 mm screws

[Disassembly]

Remove the tilt fixing handle (standalone type

only).

Tilt up the screen as much as you can

(standalone type only).

Replacement of LCD monitor must be made by specialized

service personnel.

For details, refer to Service Manual.

Summary of content (140 pages)

PAGE 1
JMA-9100 Instruction Manual 8.4.4 > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS Replacement of LCD Monitor Replacement of LCD monitor must be made by specialized service personnel. For details, refer to Service Manual. 8.4.4.1 Display Unit NCD-4990 Do not touch the LCD screen directly with your fingers. Do not touch the AR filter directly with your fingers. Perform the replacement work on a soft cloth to avoid damage to the LCD screen and other parts.
PAGE 2
JMA-9100 Instruction Manual 3) > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS Remove the screws (M6) from the four corners and displace the face cover. Remove 4) LRemove the LCD operation circuit cables and remove the face cover. Remove 5) Remove six M4 screws.
PAGE 3
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... 6) Displace the module and remove the three cables. 7) Remove the LCD module. > 8.4 REPLACEMENT OF MAJOR PARTS Remove [Assembly] 1) Tighten the lower three M4 screws halfway. 2) Connect the cables to the LCD module. 3) Align the module to the lower three screws and insert it downward. 4) Check the positions of the two bosses and ensure that appropriate space is maintained under the LCD module. Tighten the six screws evenly.
PAGE 4
JMA-9100 Instruction Manual 8.4.5 > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS Replacement of Backup Battery Replacement of backup battery must be made by specialized service personnel. For details, refer to Service Manual. A coin-cell battery maintains radar system configuration, date, and time information while power off condition. Radar system configuration is saving to non-volatile memory at fixed intervals. 8.4.5.
PAGE 5
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS [Disassembly] 1) Remove the four fixing screws to remove the cover from the display unit (NCD4990). （A flat tip screwdriver for 6 mm screws） Remove For standalone type NCD-4990 For tabletop type: NDC-1399-9 Remove 2) Remove the cable connected to the radar processing circuit board. The radar processing circuit is the first board from the left. 3) Remove the two fixing screws (M4).
PAGE 6
JMA-9100 Instruction Manual 6) > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS Insert the flat tip nonconductive sscrewdriver for adjustment or some stick to the location shown in the figure below and slide the battery sideways to remove the battery. [Assembly] 1) Check the polarity of the battery. Make sure that the battery's positive (+) side is facing up. 2) Slide the battery sideways into the battery holder. 3) Make sure that the battery is inserted fully.
PAGE 7
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8.4 REPLACEMENT OF MAJOR PARTS If you installed the battery with the wrong polarity, remove the battery immediately and do not use the same battery again. During the procedures, do not put the battery on any circuit board or conductive item. To dispose of a used battery, follow the instructions provided in Section 10.2 "DISPOSAL OF USED BATTERIES". To disassemble of a used battery, have to use non-conductive tool.
PAGE 8
JMA-9100 Instruction Manual > 8.COUNTERMEASURE FOR TROUBLE ... > 8－ 40 8.
PAGE 9
SECTION 9 TROUBLE SHOOTING AND AFTER-SALES SERVICE TROUBLE SHOOTING AND AFTER-SALES SERVICE 9.1 FAULT FINDING .....................................................................................9-1 9.1.1 List of Alarms and other Indications .............................................9-1 9.1.2 Operation Checking ........................................................................9-5 9.1.3 Fuse Checking .................................................................................9-5 9.
PAGE 10
PAGE 11
JMA-9100 Instruction Manual 9.1 > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING FAULT FINDING In case of semiconductor circuits, it is deemed that there are few cases in which the used semiconductor devices have inferior quality or performance deterioration except due to insufficient design or inspection or by other external and artificial causes.
PAGE 12
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING Table9-1： List of System Error Message Message Description TXRX (Video) Scanner: VIDEO error. TXRX (Trigger) Scanner: TRIGGER error.. TXRX (Fan 1) Scanner: FAN 1 error. TXRX (Fan 2) Scanner: FAN 2 error. TXRX (Motor) Scanner: Motor current error. Keyboard (Data) Operation unit: Communication error or checksum error. Keyboard2 (Data) Second operation unit: Communication error or checksum error.
PAGE 13
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING Table9-2： List of Notification Set GYRO Requires setting of true bearing. TM Reset Use care of resetting TM. POSN Reset Change the latitude and longitude sentence. Table9-3： List of Target Tracking Alarms and AIS Function Alarms メッセージ CPA/TCPA 内容 There is a dangerous target. Trial There is a dangerous target, when trial maneuver is active.
PAGE 14
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING Table9-5： List of Operational Error Messages and Warnings Invalid Range TM selection due to TM-disabled range (96 nm). Zooming in a ZOOM-disabled range (0.125 nm). MAX Point Tried to enter navigation information beyond the specified. Can't Transmit Tried to transmit within 5 second after standby or when the transmitter-receiver has any trouble. Invalid Data Tried to enter any data beyond its range.
PAGE 15
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.1 FAULT FINDING Table9-7： List of Interswitch Alarms and Messages 9.1.2 Pattern CHG Failed Connection change failed. Connection Masked Inhibition of control / connection is set. Master Standby The master display unit does not transmit any signals. ISW (Data) No communication, data mismatched, or checksum error. Update ISW Software Tried to enter new TXRX function, when interswitch software used old version.
PAGE 16
JMA-9100 Instruction Manual > 9.2 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING TROUBLE SHOOTING As this radar equipment includes complicated circuits, it is necessary to request a specialist engineer for repair or instructions for remedy if any circuit is defective. There are also troubles by the following causes, which should be referred to in checking or repair work. １ Poor Contact in Terminal Board of Inter-Unit Cables a. Poor contact in terminal board b.
PAGE 17
JMA-9100 Instruction Manual 9.2.1 > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.2 TROUBLE SHOOTING Special Parts NKE-2103 Table9-10： NKE-2103 (JMA-9110-6XA/6XAH、JMA-7110-6XA/6XAH) Parts No.
PAGE 18
JMA-9100 Instruction Manual 9.2.2 > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.
PAGE 19
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.
PAGE 20
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.
PAGE 21
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.
PAGE 22
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.
PAGE 23
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.
PAGE 24
JMA-9100 Instruction Manual 9.3 9.3.1 > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.3 AFTER-SALES SERVICE AFTER-SALES SERVICE Keeping period of maintenance parts Keeping period of maintenance parts is ten years from the production is discontinued. 9.3.2 When you Request for Repair If you suppose the product may be out of order, read the description in Section 9 carefully and check the suspected point again.
PAGE 25
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE > 9.3 AFTER-SALES SERVICE Radar Failure Check List i When placing an order for repair of the product, it is requested that you could confirm the check items and fill the results and sent the sheet to our contact. If there is any unclear items, contact the ship on which the product is installed, and give the correct information on the product. Ship name: i Radar general model name i. Phone: Fax: i :JMA- Serial No.
PAGE 26
JMA-9100 Instruction Manual > 9.TROUBLE SHOOTING AND AFTER-SALES SERVICE 9－ 16 > 9.
PAGE 27
SECTION 10 DISPOSAL DISPOSAL 10.1 DISPOSAL OF THE UNIT ....................................................................10-1 10.2 DISPOSAL OF USED BATTERIES .....................................................10-1 10.3 DISPOSAL OF USED MAGNETRON ..................................................10-2 10.4 DISPOSAL OF TR-TUBE .....................................................................10-2 10.5 ABOUT THE CHINA ROHS .................................................................
PAGE 28
PAGE 29
JMA-9100 Instruction Manual 10.1 > 10.DISPOSAL > 10.1 DISPOSAL OF THE UNIT DISPOSAL OF THE UNIT When disposing of this unit, be sure to follow the local laws and regulations for the place of disposal. 10.2 DISPOSAL OF USED BATTERIES When disposing of used lithium batteries, be sure to insulate the batteries by taping the + - terminals. Otherwise, heat generation, explosion or a fire may occur.
PAGE 30
JMA-9100 Instruction Manual 10.3 > 10.DISPOSAL > 10.3 DISPOSAL OF USED MAGNETRON DISPOSAL OF USED MAGNETRON Magnetron is used in the Scanner （NKE－ 2103/2254/1125/1130）and Transmitter Receiver Unit (NTG-3225/3230). • When the magnetron is replaced with a new one, return the used magnetron to our dealer or business office. For detail, consult with our dealer or business office. 10.
PAGE 31
JMA-9100 Instruction Manual 10.5 > 10.DISPOSAL > 10.
PAGE 32
JMA-9100 Instruction Manual > 10.DISPOSAL > 10.
PAGE 33
SECTION 11 SPECIFICATION SPECIFICATION 11.1 JMA-9133-SA TYPE RADAR ...............................................................11-1 11.2 JMA-9132-SA TYPE RADAR ............................................................... 11-2 11.3 JMA-9123-7XA/9XA TYPE RADAR ....................................................11-3 11.4 JMA-9122-6XA/9XA TYPE RADAR ....................................................11-4 11.5 JMA-9122-6XAH TYPE RADAR .........................................................11-5 11.
PAGE 34
11.18 11.19 11.20 11.21 11.22 Target Tracking Function .................................................................11-20 AIS FUNCTION ...................................................................................11-21 PERFORMANCE MONITOR (NJU-84) ..............................................11-22 PERFORMANCE MONITOR (NJU-85) ..............................................11-22 AC-DC CONVERTER (NBA-5135) .....................................................
PAGE 35
JMA-9100 Instruction Manual 11.1 > 11.SPECIFICATION > 11.1 JMA-9133-SA TYPE RADAR JMA-9133-SA TYPE RADAR GENERAL SPECIFICATION Class of emission P0N Display Color Raster Scan Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm) Range Scale 0.125、0.25、0.5、0.75、1.
PAGE 36
JMA-9100 Instruction Manual > 11.2 11.SPECIFICATION > 11.2 JMA-9132-SA TYPE RADAR JMA-9132-SA TYPE RADAR GENERAL SPECIFICATION Class of emission P0N Display Color Raster Scan Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm) Range Scale 0.125, 0.25, 0.5, 0.75, 1.
PAGE 37
JMA-9100 Instruction Manual 11.3 > 11.SPECIFICATION > 11.3 JMA-9123-7XA/9XA TYPE RADAR JMA-9123-7XA/9XA TYPE RADAR GENERAL SPECIFICATION Class of emission P0N Display Color Raster Scan Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm) Range Scale 0.125, 0.25, 0.5, 0.75, 1.
PAGE 38
JMA-9100 Instruction Manual 11.4 > 11.SPECIFICATION > 11.4 JMA-9122-6XA/9XA TYPE RADAR JMA-9122-6XA/9XA TYPE RADAR GENERAL SPECIFICATION Class of emission P0N Display Color Raster Scan Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm) Range Scale 0.125, 0.25, 0.5, 0.75, 1.
PAGE 39
JMA-9100 Instruction Manual 11.5 > 11.SPECIFICATION > 11.5 JMA-9122-6XAH TYPE RADAR JMA-9122-6XAH TYPE RADAR GENERAL SPECIFICATION Class of emission P0N Display Color Raster Scan Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm) Range Scale 0.125, 0.25, 0.5, 0.75, 1.
PAGE 40
JMA-9100 Instruction Manual 11.6 > 11.SPECIFICATION > 11.6 JMA-9110-6XA TYPE RADAR JMA-9110-6XA TYPE RADAR GENERAL SPECIFICATION Class of emission P0N Display Color Raster Scan Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm) Range Scale 0.125, 0.25, 0.5, 0.75, 1.
PAGE 41
JMA-9100 Instruction Manual 11.7 > 11.SPECIFICATION > 11.7 JMA-9110-6XAH TYPE RADAR JMA-9110-6XAH TYPE RADAR GENERAL SPECIFICATION Class of emission P0N Display Color Raster Scan Screen 23.1inch LCD (Effective diameter of Radar: more than 320mm) Range Scale 0.125, 0.25, 0.5, 0.75, 1.
PAGE 42
JMA-9100 Instruction Manual 11.8 SCANNER UNIT > 11.SPECIFICATION > 11.8 SCANNER UNIT (NKE-1139) SCANNER UNIT (NKE-1139) NKE-1139 Dimension Height 791 x Swing Circle 4000 (mm) Mass Approx.150kg Polarization Horizontal Directional Characteristics Horizontal beam width : 1.9° Vertical beam width : 25° Side lobe Level : below -26dB (within +/-10°) : below -30dB (outside +/-10°) Revolution Approx.24rpm Power Supply for Motor AC100 - 115V、50/60Hz、1φ or AC220 - 240V、50/60Hz、1φ Maximum Wind Velocity 51.
PAGE 43
JMA-9100 Instruction Manual 11.9 > 11.SPECIFICATION > 11.9 SCANNER UNIT (NKE-1130) SCANNER UNIT (NKE-1130) SCANNER UNIT NKE-1130 Dimension Height 791 x Swing Circle 4000 (mm) Mass Approx.180kg Polarization Horizontal Directional Characteristics Horizontal beam width : 1.9° Vertical beam width : 25° Side lobe Level : below -26dB (within +/-10°) : below -30dB (outside +/-10°) Revolution Approx.24rpm Power Supply for Motor AC100 - 115V、50/60Hz、1φ or AC220 - 240V、50/60Hz、1φ Maximum Wind Velocity 51.
PAGE 44
JMA-9100 Instruction Manual 11.10 SCANNER UNIT > 11.SPECIFICATION > 11.10 SCANNER UNIT (NKE-1129-7/9) SCANNER UNIT (NKE-1129-7/9) NKE-1129-7/9 Dimension 7ft 9ft Mass 7ft 9ft Height 536 x Swing Circle 2270 (mm) Height 536 x Swing Circle 2825 (mm) Approx.51kg Approx.53kg Polarization Horizontal Directional Characteristics Horizontal beam width : : Vertical beam width : Side lobe Level : : 1.0° (7ft) 0.8° (9ft) 20° below -26dB (within +/-10°) below -30dB (outside +/-10°) Revolution Approx.
PAGE 45
JMA-9100 Instruction Manual 11.11 SCANNER UNIT > 11.SPECIFICATION > 11.11 SCANNER UNIT (NKE-1125-6/9) SCANNER UNIT (NKE-1125-6/9) NKE-1125-6/9 Dimension 6ft 9ft Mass 6ft 9ft Height 536 x Swing Circle 1910 (mm) Height 536 x Swing Circle 2825 (mm) Approx. 55kg Approx. 60kg Polarization Horizontal Directional Characteristics Horizontal beam width : : Vertical beam width : Side lobe Level : : 1.2° (6ft) 0.8° (9ft) 20° below -26dB (within +/-10°) below -30dB (outside +/-10°) Revolution Approx.
PAGE 46
JMA-9100 Instruction Manual 11.12 SCANNER UNIT > 11.SPECIFICATION > 11.12 SCANNER UNIT (NKE-2254-6HS) SCANNER UNIT (NKE-2254-6HS) NKE-2254-6HS Dimension Height 536 x Swing Circle 1910 (mm) Mass Approx. 55kg Polarization Horizontal Directional Characteristics Horizontal beam width : 1.2° Vertical beam width : 20° Side lobe Level : below -26dB (within +/-10°) : below -30dB (outside +/-10°) Revolution Approx.24rpm Power Supply for Motor DC24V Maximum Wind Velocity 51.
PAGE 47
JMA-9100 Instruction Manual 11.13 SCANNER UNIT > 11.SPECIFICATION > 11.13 SCANNER UNIT (NKE-2103-6) SCANNER UNIT (NKE-2103-6) NKE-2103-6HS Dimension Height 458 x Swing Circle 1910 (mm) Mass Approx. 40kg Polarization Horizontal Directional Characteristics Horizontal beam width : 1.2° Vertical beam width : 20° Side lobe Level : below -26dB (within +/-10°) : below -30dB (outside +/-10°) Revolution Approx.24rpm Power Supply for Motor DC24V Maximum Wind Velocity 51.
PAGE 48
JMA-9100 Instruction Manual 11.14 SCANNER UNIT > 11.SPECIFICATION > 11.14 SCANNER UNIT (NKE-2103-6HS) SCANNER UNIT (NKE-2103-6HS) NKE-2103-6HS Dimension Height 458 x Swing Circle 1910 (mm) Mass Approx. 40kg Polarization Horizontal Directional Characteristics Horizontal beam width : 1.2° Vertical beam width : 20° Side lobe Level : below -26dB (within +/-10°) : below -30dB (outside +/-10°) Revolution Approx.24rpm Power Supply for Motor DC24V Maximum Wind Velocity 51.
PAGE 49
JMA-9100 Instruction Manual 11.15 > 11.SPECIFICATION > 11.15 TRANSMITTER RECEIVER UNIT (NTG-3230) TRANSMITTER RECEIVER UNIT (NTG-3230) SCANNER UNIT NTG-3230 Dimension :Width 615 x Depth 365 x Height 615 (mm) 構造 Wall Mount, Drip Proof Mass Approx.33kg Transmitting Frequency 3050 ± 20MHz Transmitting Power 30kW Transmitting Tube Magnetron [M1555] TX Pulse width / Repetition SP1：0.07μs/2250Hz Frequency MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.
PAGE 50
JMA-9100 Instruction Manual 11.16 > 11.SPECIFICATION > 11.16 TRANSMITTER RECEIVER UNIT (NTG-3225) TRANSMITTER RECEIVER UNIT (NTG-3225) SCANNER UNIT NTG-3225 Dimension :Width 460 x Depth 227 x Height 461 (mm) 構造 Wall Mount, Drip Proof Mass Approx.15kg Transmitting Frequency 9410 ± 30MHz Transmitting Power 25kW Transmitting Tube Magnetron[M1568BS] TX Pulse width / Repetition SP1：0.07μs/2250Hz Frequency MP1：0.2μs/2250Hz MP2：0.3μs/1900Hz、MP3：0.4μs/1400Hz LP1：0.8μs/750Hz、LP2：1.0μs/650Hz LP3：1.
PAGE 51
JMA-9100 Instruction Manual 11.17 > 11.SPECIFICATION > 11.17 DISPLAY UNIT (NCD-4990) DISPLAY UNIT (NCD-4990) DISPLAY UNIT NCD-4990 Dimension Width 700 x Depth 850 x Height 1100 (mm) Structure Self-Standing, Drip Proof Mass Approx.130kg Screen 23.1inch Color LCD (Effective Diameter, more than 320mm) Viewing Distance 1m from the center of Display Range Scale 0.125, 0.25, 0.5, 0.75, 1.5, 3, 6, 12, 24, 48, 96NM Range Marker 0.025, 0.05, 0.1, 0.25, 0.
PAGE 52
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.
PAGE 53
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.17 DISPLAY UNIT (NCD-4990) Maximum current 200mA (SYSALM, ALPAALM, PWRALM port at terminal board TB4601) i.
PAGE 54
JMA-9100 Instruction Manual 11.18 > 11.SPECIFICATION > 11.
PAGE 55
JMA-9100 Instruction Manual 11.19 > 11.SPECIFICATION > 11.19 AIS FUNCTION AIS FUNCTION AIS 機能 Available range scale Activation All range Activation mode Manual/AUTO（AUTO mode uses Auto-activation Zone） Manual Cancellation Any one Target Presentation Number of Activated Target 100 Targets Number of Target 300 Targets (sleeping target and activated target) Past Position True/Relative Display Number of Dots…10 points Display Interval Time…0.5 / 1 / 2/ 4 min Display Interval distance…0.1 / 0.2 / 0.
PAGE 56
JMA-9100 Instruction Manual > 11.SPECIFICATION > 11.20 PERFORMANCE MONITOR (NJU-84) Accuracy of Display Complied with IMO Requirement System Failure Alarm Visible / Audible Alarm Speed Input Auto (LOG) 11.20 PERFORMANCE MONITOR (NJU-84) PERFORMANCE MONITORNJU-84 Dimension Width 130 x Depth 180 x Height 70 (mm) Mass Approx.0.7kg Operating Frequency 3050 ± 30MHz 11.21 PERFORMANCE MONITOR (NJU-85) PERFORMANCE MONITORNJU-85 Dimension Width 130 x Depth 149 x Height 70 (mm) Mass Approx.0.
PAGE 57
Appendix A NQE-3141 Interswitch Unit NQE-3141 Interswitch Unit A.1 OVERVIEW ............................................................................................ A-1 A.1.1 Overview ......................................................................................... A-1 A.1.2 Interswitch Setup ........................................................................... A-1 A.2 INTERSWITCH OPERATION ................................................................ A-3 A.2.1 Operation Flow .........
PAGE 58
PAGE 59
JMA-9100 Instruction Manual A.1 A.1.1 > A.NQE-3141 Interswitch Unit > A.1 OVERVIEW OVERVIEW Overview Interswitch NQE-3141 is equipment that enables free changeover between radar display units installed on the bridge and antenna units having different characteristics. If display unit is turned off or malfunctioned, the scanner unit can be controlled by other display unit. If interswitch unit had malfunctioned, the radar system is switched to standalone mode. Up to 8 units can be changed over.
PAGE 60
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.1 OVERVIEW upper left of the display Connected Scanner Unit Connection Mode Connection Switch The upper stand indicates the number of the connected scanner unit. The lower stand indicates the connection mode. i. Master :Mode in which the scanner unit can be controlled by the display unit Slave :Mode in which the scanner unit cannot be controlledi When Slave is selected, transmission / standby and pulse length cannot be changed.
PAGE 61
JMA-9100 Instruction Manual A.2 > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION INTERSWITCH OPERATION Follow the flowchart below to change the current interswitch connection pattern. A.2.1 Operation Flow Place the transmission standby state . Open the Inter Switch Menu . Change the connection pattern . Close the Inter Switch Menu .
PAGE 62
JMA-9100 Instruction Manual A.2.2 > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION Inter Switch Menu The Inter Switch Menu can be opened only when the transmission standby state. Procedures 1) Press the [TX/STBY] key to stop transmitting. The transmission standby state will be placed. 2) Move the cursor onto the Interswitch connection change (upper left of the display), and left-click. The Inter Switch Menu will appear. Exit 1) Left-click the 0.Exit button.
PAGE 63
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION a. Connection pattern If this button is clicked, the connection pattern is selected. The display unit in operation is enclosed in a square □ . The background of the current connection pattern display is highlighted. b. Set If this button is clicked, the change of connection is determined. c. Exit If this button is clicked, the Inter Switch Menu is closed .
PAGE 64
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION b. Display unit connected as master c. Display unit connected as slave If this button is clicked, select / cancel the display unit. If this button is clicked in the naming a display unit or scanner unit mode , the name input window is opened . d. Name If this button is clicked, set to the display or scanner unit rename mode. e. File Operations If this button is clicked, the File Operations menu is opened.。 f.
PAGE 65
JMA-9100 Instruction Manual A.2.4 > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION Change of Connection Pattern (with 3 or More Display Units) If three or more display units are installed, the layout of connection patterns needs to be set. Procedures 1) Open the Inter Switch Menu (with 3 or More Display Units). 2) Move the cursor onto the display unit (Section b. "Display unit connected as master" or Section c. "Display unit connected as slave") to be changed , and left- click.
PAGE 66
JMA-9100 Instruction Manual A.2.5 > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION Operating Connection Pattern Files (File Operations) Frequently used connection patterns can be read easily by saving interswitch connection patterns. [1] Loading connection patterns (Load) Procedures 1) Open the Inter Switch Menu (with 3 or More Display Units). 2) Left-click the button. 2. File Operation The File Operations menu will appear. 3) Left-click the 3. Load button.
PAGE 67
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.2 INTERSWITCH OPERATION [3] Erasing a connection pattern (Erase) Procedures 1) Open the Inter Switch Menu (with 3 or More Display Units). 2) Left-click the 2. File Operation button. The File Operations window will appear. 3) Left-click the button. 3. Erase The Erase menu will appear. The list of connection patterns stored in the memory will be displayed. 4) Left-click the button corresponding to the file to be erased.
PAGE 68
JMA-9100 Instruction Manual A.3 A.3.1 > A.NQE-3141 Interswitch Unit > A.3 REFERENCE REFERENCE Preheat Time after Change of Connection Pattern After the current interswitch connection pattern has been changed, operation needs to wait until the system is ready. This is because the preheat time varies depending on the previous connection of the scanner unit and display unit. The wait time is necessary for protecting the electronic tubes that emit radio waves. A.3.
PAGE 69
JMA-9100 Instruction Manual > A.NQE-3141 Interswitch Unit > A.3 REFERENCE pulse length, the range of the slave display unit may be forcibly changed. In this case, Master Range CHG is shown in the alarm indication (lower right of the display), and the alarm sounds. A.3.4 Setting at Installation Setting of the interswitch circuit (CCL-304*) The settings of the DIP switches SW11 to SW13 are shown below.
PAGE 70
JMA-9100 Instruction Manual 2) 1 > A.NQE-3141 Interswitch Unit > A.3 REFERENCE SW12 setting (radar connection settings) 2 3 4 5 6 7 8 ON OFF Radar connection settings ON No.8 display unit connected OFF No.8 display unit not connected ON No.7 display unit connected OFF No.7 display unit not connected ON No.6 display unit connected OFF No.6 display unit not connected ON No.5 display unit connected OFF No.5 display unit not connected ON No.4 display unit connected OFF No.
PAGE 71
Appendix B DRAWINGS DRAWINGS B.1 Interconnection Diagram of Display Unit ........................................... B-1 B.1.1 NCD-4990 ........................................................................................ B-2 B.1.2 NCD-4990 w/NBA-5135 ................................................................... B-3 B.1.3 NCD-4990T ...................................................................................... B-4 B.1.4 NCD-4990T w/NBA-5135 ..................................................
PAGE 72
B.5.4 NKE-1129, NTG-3225 / NKE-1139, NTG-3230 ............................. B-18 B.6 Interconnection Diagram of Scanner Unit ....................................... B-19 B.6.1 NKE-2103 ...................................................................................... B-20 B.6.2 NKE-2254 ...................................................................................... B-21 B.6.3 NKE-1125 (AC110V) ...................................................................... B-22 B.6.4 NKE-1125 (AC220V) ....
PAGE 73
JMA-9100 Instruction Manual B.1 > B.DRAWINGS > B.
PAGE 74
NCD-4990 B.1.
PAGE 75
NCD-4990 w/NBA-5135 B.1.
PAGE 76
NCD-4990T B.1.
PAGE 77
NCD-4990T w/NBA-5135 B.1.
PAGE 78
JMA-9100 Instruction Manual B.DRAWINGS > B.1 Interconnection Diagram of Display Unit NWZ-170-R H-7WSRD0002A LCD CCK-972 PC710 AC 2m VM0301-VM0303B2Mｸﾛ CBD-1661 OUTLET AC 1 00V 24 0V 9P 2m H-7ZCRD1329A FAN ALM CQD-2097 J4309 DVI DVI 2m H-7ZCRD1345 RGB CDC-1324 J4406 B.1.
PAGE 79
JMA-9100 Instruction Manual B.DRAWINGS > B.1 Interconnection Diagram of Display Unit NWZ-170-RT H-7WSRD0002A LCD CCK-972 PC710 AC 5m VM0301-VM0303B5Mｸﾛ CBD-1661 OUTLET AC 1 00V 24 0V 9P 5m H-7ZCRD1330A FAN ALM CQD-2097 J4309 DVI DVI 5m H-7ZCRD1346 RGB CDC-1324 J4406 B.1.
PAGE 80
JMA-9100 Instruction Manual B.DRAWINGS > B.1 Interconnection Diagram of Display Unit NCE-5163-R OPERATION UNIT NCE-5163-R OPERATION CIRCUIT B CCK-974 PC620 OPERATION CIRCUIT A CCK-973 PC610 A1 7P J6201 14P J6101 15P J6102 6P J6411 6P J6408 2P 7P J6406 J6405 14P J6404 W64 H-7ZCRD1334 W65 H-7ZCRD1335 W63 H-7ZCRD1333A SP1 W62 H-7ZCRD1332 B.1.
PAGE 81
JMA-9100 Instruction Manual B.DRAWINGS > B.1 Interconnection Diagram of Display Unit NCE-5163-RT OPERATION UNIT NCE-5163-RT OPERATION CIRCUIT B CCK-974 PC620 OPERATION CIRCUIT A CCK-973 PC610 A1 7P J6201 14P J6101 15P J6102 6P J6411 6P J6408 2P 7P J6406 J6405 14P J6404 W64 H-7ZCRD1334 W65 H-7ZCRD1335 W63 H-7ZCRD1333A SP1 W62 H-7ZCRD1332 B.1.
PAGE 82
JMA-9100 Instruction Manual B.DRAWINGS > B.1 Interconnection Diagram of Display Unit NBA-5135 W6 H-7ZCRD1499 1 2 3 1 FS1 TB521 1 2 RED 3 BLK W1 H-7ZCRD1495 WHT 2 3 TB 522 1 2 3 BLK WHT WHT W5 H-7ZCRD1499 W2 H-7ZCRD1496 Twisted RED W4 H-7ZCRD1498 WHT BLK U + + + - V FL1 LF-210 - - A1 AES300-24B W3 H-7ZCRD1497 RED BLK WHT L FG BLK N u FG v RED WHT B.1.
PAGE 83
Power System Daigram of Display Unit B.2 FG U,V DC+24V U,V R ED W HT BL U W HT AC OUT2 B ATTERY IN AC OUT2 LCD PANEL H-7WSRD0002A 2P 2P 20P 3.3V,5V, 12V,-12V 18P U 3.3V,5V,12V,-12V +48V,DC+24V 8P 4351A07335 FIL TER 8P J711 8P H-7ZCR D1328 9P 2m H -7ZCRD 1329A (N WZ-170-R ) 15P J 4409 V GA 15P J 4405 V GA 28P J 4406 D VI-D 8P J 4407 R J-45 64P J4401 64P J4101 5V 64P J4403 64P J4404 3.
PAGE 84
Signal Flow Diagram of Display Unit B.
PAGE 85
Primary Power System Diagram B.4 AC100-115V AC220-240V 50/60Hz,1φ OVER VOLTAGE PROTECTION LINE FILTER P+12V SCANNER X BAND_2.5A, S BAND_3.0A INTERSWITCH=1A OPERATION UNIT=0.5A(typ) GYRO I/F CIRCUIT=0.1A(typ) RADAR PROCESS CIRCUIT = 1.2A(typ) ARPA PROCESS CIRCUIT = 0.15A(typ) AIS PROCESS CIRCUIT = 0.15(typ) TERMINAL BOARD = 1.0A(typ) +48V±3V +5.0V +3.3V RADAR PROCESS CIRCUIT = 2.2A(typ) ARPA PROCESS CIRCUIT = 0.1A(typ) AIS PROCESS CIRCUIT = 0.1(typ) TERMINAL BOARD = 0.
PAGE 86
JMA-9100 Instruction Manual B.5 > B.DRAWINGS > B.
PAGE 87
JMA-9100 Instruction Manual B.5.1 > B.DRAWINGS > B.
PAGE 88
> JMA-9100 Instruction Manual B.5.2 B.DRAWINGS > B.
PAGE 89
JMA-9100 Instruction Manual B.5.3 > B.DRAWINGS > B.
PAGE 90
JMA-9100 Instruction Manual B.5.4 > B.DRAWINGS > B.
PAGE 91
JMA-9100 Instruction Manual B.6 > B.DRAWINGS > B.
PAGE 92
NKE-2103 B.6.1 S.G. S.G. 100pF× 3 MAG GRN A103 NJC 4002 DUMMY NJC9952 A104 ANTENNA NAX-16B-4/6 FILTER DISPLAY UNIT 6.TXI 7.TXE 8.NC 1.PTI 2.PTE 3.LVR 4.PMS 5.E J8 1.ΦZ 2.E 3.ΦA 4.ΦB 5.+12V 6.F.G. J208 P8 YEL BLK BLU WHT RED SHIELD (W108) Z CRD1305※ SE B102 (RECEIVER UNIT INTERCONNECTION CMA-823) TRANSMITTER/RECEIVER UNIT ＮZT－２１０３ TRANSMITTER/RECEIVER UNIT INTERCONNECTION CMK-599 RECEIVER UNIT ＮＲＧ－６１０ CAE-529-1 IF AMP CIRCUIT (PC301) 5 3.
PAGE 93
NKE-2254 B.6.2 RECEIVER CIRCUIT CMA-866A BM15B-XASS-TE J101 RECEIVER UNIT NRG-162A P3001 (W001) ZCRD1251※ P1110 J1110 IL-4P J1191 IL-G -11P Ａ301 NJS6930 P1111 1 2 3 ② ② Ａ104 NJC 9952 ANTENNA FILTER Ａ103 NJC4002 DUMMY ① ③ ① J2102 (W107) ZCRD1259※ P2101 IL-10P 1.SHORT 2.MAG I No.2 3.X1 MODULATOR No.1 4.X2 5.TI CIRCUIT 6.TIE CPA-264 7.+15V J2103 8.G ND 350209-2 J2101 9.NC 1.X1 1586514-2 10.NC 2.X2 P1002 DISPLAY UNIT (W106) ZC RD1258※ 2 1 MAG T1 C201 0.
PAGE 94
NKE-1125 (AC110V) B102 RECEIVER UNIT NRG-162A J101 RECEIVER CIRCUIT CMA-866A BM15B-XASS-TE IL-G-8P J1109 P1110 IL-4P J1191 IL-G -11P J1110 IL-G-3P J1114 1.SHORT 2.MAGI 3.X1 4.X2 5.TI 6.TIE 7.+15V 8.GND 9.NC 10.NC 11.NC 12.NC 1.HMC NT 2.+15V 3.GND 1.+15V 2.+12V 3.G ND 4.GND 5.-15V 6.10V 7.10VE 8.+5V 1.MC T 2.MBK 3.TISTOP 4.G ND 5.MPS 6.MIER IL-G-2P J1105 A301 NJS6930 P1111 ② ② Ａ104 NJC9952 ANTENNA FILTER A103 NJC4002 DUMMY ① ③ ① J2102 (W107) ZCRD1259※ P2101 IL-10P 1.SHORT 2.
PAGE 95
NKE-1125 (AC220V) B102 RECEIVER UNIT NRG-162A J101 RECEIVER CIRCUIT CMA-866A BM15B-XASS-TE IL-G-8P J1109 P1110 IL-4P J1191 IL-G -11P J1110 IL-G-3P J1114 1.SHORT 2.MAGI 3.X1 4.X2 5.TI 6.TIE 7.+15V 8.GND 9.NC 10.NC 11.NC 12.NC 1.HMC NT 2.+15V 3.GND 1.+15V 2.+12V 3.G ND 4.GND 5.-15V 6.10V 7.10VE 8.+5V 1.MC T 2.MBK 3.TISTOP 4.G ND 5.MPS 6.MIER IL-G-2P J1105 A301 NJS6930 P1111 ② ② Ａ104 NJC9952 ANTENNA FILTER A103 NJC4002 DUMMY ① ③ ① J2102 (W107) ZCRD1259※ P2101 IL-10P 1.SHORT 2.
PAGE 96
NKE-1129 (AC110V) TB103 U1 V1 W1 +12V C2 ΦZE ΦZ ΦA E ΦB （W301) ZCRD1285※ RED.T 1 2 4 S101 S-32 RED 5 S.G. C102 2200p 50V RED.T S.G. C101 + 1000μ 16V BLK.T SE 7 B102 8 RED ENCORDER CHT-71A1 J81 P81 AC100V （W302) ZCRD1286※ HEATER CONTROL PART CHG-216 (OPTION) W401 7Z CRD1508※ WHT.T R4 R3 R2 120Ω ×4 30W R1 330Ω 30W ×1 R1 B101 1 0 J1 5 MOTOR B3P-VH P1502 WC1 R2 1.2kΩ 30W AC100V MOTOR DRIVER CBD-2001 R1 1.
PAGE 97
NKE-1129 (AC220V) TB103 U1 V1 W1 +12V C2 ΦZE ΦZ ΦA E ΦB （W301) ZCRD1285※ RED.T 1 2 4 S101 S-32 RED 5 S.G. C102 2200p 50V RED.T S.G. C101 + 1000μ 16V BLK.T SE 7 B102 8 RED ENCORDER CHT-71A1 J81 P81 AC100V （W302) ZCRD1286※ HEATER CONTROL PART CHG-216 (OPTION) W401 7Z CRD1508※ WHT.T R4 R3 R2 120Ω ×4 30W R1 330Ω 30W ×1 R1 B101 1 0 J1 5 MOTOR B3P-VH P1502 WC1 R2 1.2kΩ 30W AC220V MOTOR DRIVER CBD-2000 R1 1.
PAGE 98
NTG-3225 B.6.7 (W014) ZCRD1241※ BM15B-XASS-TE J101 RECEIVER CIRCUIT CMA-866A RECEIVER UNIT NRG-162A P3001 P1109 P1110 IL-4P J1109 IL-G -11P J1191 IL-G-8P J1110 IL-G-6P T/R CONTROL CIRCUIT CMC-1205R Ａ302 NJS6926 1.SHORT 2.MAGI 3.X1 4.X2 5.TI 6.TIE 7.+15V 8.GND 9.NC 10.NC 11.NC 12.NC 1.HMCNT 2.+15V 3.GND 1.+15V 2.+12V 3.G ND 4.GND 5.-15V 6.10V 7.10VE 8.+5V J13 1.MCT 2.MBK 3.TISTOP 4.GND 5.MPS 6.
PAGE 99
NKE-1130 (AC110V) SE B102 IL-7P J102 IF CIRCUIT CAE-499 IL-9P J101 P3002 P1110 CAF-595 RF CIRCUIT CMA-902 R ECEIRVER UNIT INTERCONN ECTION IL-G -3P J1114 IL-4P 1.SHORT 2.MAGI 3.X1 4.X2 5.TI 6.TIE 7.+15V 8.G ND 9.NC 10.NC 11.NC 12.NC 1.HMCNT 2.+15V 3.G ND J1113 1.MCT 2.MBK 3.TISTOP 4.GND 5.MPS 6.MIE R 1.+15V 2.+12V 3.G ND 4.G ND 5.-15V 6.10V 7.10VE 8.
PAGE 100
NKE-1130 (AC220V) SE B102 IL-7P J102 IF CIRCUIT CAE-499 IL-9P J101 P3002 P1110 CAF-595 RF CIRCUIT CMA-902 R ECEIRVER UNIT INTERCONN ECTION IL-G -3P J1114 IL-4P 1.SHORT 2.MAGI 3.X1 4.X2 5.TI 6.TIE 7.+15V 8.G ND 9.NC 10.NC 11.NC 12.NC 1.HMCNT 2.+15V 3.G ND J1113 1.MCT 2.MBK 3.TISTOP 4.GND 5.MPS 6.MIE R 1.+15V 2.+12V 3.G ND 4.G ND 5.-15V 6.10V 7.10VE 8.
PAGE 101
NKE-1139 (AC110V) 5 2 9 6 3 S101 S-32 8 C102 2200p 50V WHT.T （100W） WHT.T TR101 C101 + 1000μ 16V TH101 W401 7ZCRD1509 （W301) ZCRD1287※ RED RED.T BLK.T RED WHT RED.T BLK.T （W305) ZCRD1457※ （W302) ZCRD1288※ HEATER CONTROL PART CHG -215 (OPTION) (W308) ZCRD1553※ P1941 J1941 1.+12V 2.NC 3.+12VE S3B-XH-A B2PS-VH 1.VE RR1 2.E J1912 P1912 R4 R3 R2 120Ω ×4 30W R1 330Ω 30W ×1 R1 P1911 J1911 1-350209-0 J1905 P1905 B3P-VH PC1501 1.R1 B201 H-7EPRD0035 2.NC 3.
PAGE 102
NKE-1139 (AC220V) 5 2 9 6 3 S101 S-32 8 C102 2200p 50V WHT.T （100W） WHT.T TR101 C101 + 1000μ 16V TH101 W401 7ZCRD1509 （W301) ZCRD1287※ RED RED.T BLK.T RED WHT RED.T BLK.T （W305) ZCRD1457※ （W302) ZCRD1288※ HEATER CONTROL PART CHG -215 (OPTION) (W308) ZCRD1553※ P1941 J1941 1.+12V 2.NC 3.+12VE S3B-XH-A B2PS-VH 1.VERR 2.E J1912 P1912 R4 R3 R2 120Ω ×4 30W R1 330Ω 30W ×1 R1 P1911 J1911 1-350209-0 J1905 P1905 B3P-VH PC1501 1.R1 B201 H-7EPRD0034 2.NC 3.
PAGE 103
NTG-3230 B.6.12 (W014) ZCRD1226※ IL-9P J101 IL-7P J102 IF CIRCUIT CAE-499 RECEIVER UNIT NRG-229 J1 P3001 (W002) ZC RD1218※ P3002 P1110 IL-4P J1191 CMA-902 RF CIRCUIT CAF-595 IL-G-3P J13 1.MCT 2.MBK 3.TI STOP 4.GND 5.MPS 6.MIER 1.+15V 2.+12V 3.GND 4.GND 5.-15V 6.10V 7.10VE 8.+5V 1.HMCNT 2.+15V 3.GND 1.SHORT 2.MAGI 3.X1 4.X2 5.TI 6.TI E 7.+15V 8.GND 9.N C 10.NC 11.NC 12.
PAGE 104
JMA-9100 Instruction Manual B.7 > B.DRAWINGS > B.
PAGE 105
B －33 Fig B-29: Terminal Board Connection Diagram of JMA-9110-6XA/JMA-9110-6XAH 250V -M PYCYS-7 0. 6/ 1kV-D PYCYS-1.5 ( NEAREST AP PRO ACH) ALARM MONITORING SYSTEM GYRO (200P /NM) 0. 6/1kV-D PYCYS-1.
PAGE 106
B －34 250V -M PYCYS-7 0. 6/1kV-D PYCYS-1.5 250V-T TYCS-4 250V-T TYCS-1 250V-T TYCS-1 250V-T TYCS-1 250V-T TYCS-1 0. 6/1kV-D PYCYS-1.
PAGE 107
B －35 Fig B-31: Terminal Board Connection Diagram of JMA-9122-6XAH 250V -M PYCYS-7 0. 6/1kV-D PYCYS-1.5 ( NEAREST AP PRO ACH) ALARM MONITORING SYSTEM GYRO (200P /NM) 0. 6/1kV-D PYCYS-1.
PAGE 108
B －36 Fig B-32: Terminal Board Connection Diagram of JMA-9122-6XAH (desktop) 250V -M PYCYS-7 0.6/1kV-D PYCYS-1.5 250V-T TYCS-4 250V-T TYCS-1 250V-T TYCS-1 250V-T TYCS-1 250V-T TYCS-1 0. 6/1kV-D PYCYS-1.
PAGE 109
B －37 Fig B-33: Terminal Board Connection Diagram of JMA-9122-6XA/9XA 250V -M PYCYS-7 0. 6/1kV-D PYCYS-1.5 ( NEAREST AP PRO ACH) ALARM MONITORING SYSTEM GYRO (200P /NM) 0. 6/1kV-D PYCYS-1.
PAGE 110
B －38 Fig B-34: Terminal Board Connection Diagram of JMA-9123-7XA/9XA 250V -M PYCYS-7 0. 6/1kV-D PYCYS-1.5 250V-T TYCS-4 250V-T TYCS-1 250V-T TYCS-1 250V-T TYCS-1 250V-T TYCS-1 250V-T TYCS-1 0. 6/1kV-D PYCYS-1.
PAGE 111
B －39 Fig B-35: Terminal Board Connection Diagram of JMA-9132-SA 250V -M PYCYS-7 0. 6/1kV-D PYCYS-1.5 ( NEAREST AP PRO ACH) ALARM MONITORING SYSTEM GYRO (200P /NM) 0. 6/1kV-D PYCYS-1.
PAGE 112
B －40 Fig B-36: Terminal Board Connection Diagram of JMA-9133-SA 250V -M PYCYS-7 0. 6/1kV-D PYCYS-1.5 250V-T TYCS-4 250V-T TYCS-1 250V-T TYCS-1 250V-T TYCS-1 0. 6/1kV-D PYCYS-1.
PAGE 113
JMA-9100 Instruction Manual B.7.9 > B.DRAWINGS > B.7 Terminal Board Connection Diagram NCD-4990T DISPLAY UNIT NCD-4990T MONITOR UNIT NWZ-170 OPERATION UNIT NCE-5163 J4406 DVI-D DSUB -9P FEMALE J4309 RADAR PROCESS CIRCUIT CDC-1324 TERMINAL BOARD CQD-2097 Option Option for X-band 10kW and X-band 25kW-H S.
PAGE 114
JMA-9100 Instruction Manual > B.8 B.DRAWINGS > B.
PAGE 115
JMA-9100 Instruction Manual > B.DRAWINGS > B.
PAGE 116
JMA-9100 Instruction Manual B.9 B.9.1 > B.DRAWINGS > B.
PAGE 117
B －45 Fig B-40: Terminal Board Connection Diagram of NQE-3141-4A H-2695111153 BR N PN K BL K 15 14 13 12 11 VDOUT 1 VDOUT 1E TRIGOUT 1 TRIGOUT 1E 16 17 18 19 20 MTROUT 1MTORUT 1E 25 26 WH T-WHT WHT -YEL CL R PUR RED 2 M TROUT 1+ 24 11 10 9 8 7 6 5 4 3 2 1 TB912 BZOUT 1 BZOUT 1E 22 23 21 H-2695111153 ORG PWROUT 1E 15 BR N PN K OR G BLK WH T-WH T WH T-BLU G RN YEL BLU 1 WHT-YEL WHT-WHT CLR PUR RED 2 BRN BLK PNK 15 14 13 12 11 10 9 8 7 6 5
PAGE 118
H-7ZCRD0971 1 2 - J1 VIN + VIN CBD-1675 5V GND +15V GND GND H-7ZCRD0972 1 2 3 4 5 6 P903 5V GND +15V GND GND J3 J3 CQD-1973 CH-2 CH-3 CH-4 > CQD-1973 CH-1 CCL-304 B.DRAWINGS ＴＢ914 ＴＢ913 ＴＢ911 B －46 26 H-7ZCRD0970A 26 1 1 ＴＢ912 26 H-7ZCRD0970A 26 1 1 Fig B-41: Interconnection Diagram of NQE-3141-2A Terminal board Terminal board J4306 J4307 (ISW-1CH) (ISW-1CH) J903 -15V > Terminal board J4308 ISW 1 2 -15V 1 2 3 4 5 6 P902 B.9.2 J2 JMA-9100 Instruction Manual B.
PAGE 119
TB901 LF901 U 2 4 AC100V-240V 1 3 C901 V E C902 TE901 C903 A LINE FG CB901 B C D LOAD CD9 01 H-7ZCRD0919 B901 1 3 5 P901 FG AC(N) AC(L) CN1 CBA-357 B －47 H-7ZCRD0920 J903 J909 FANP LS FANE FANV J905 PO WLED E TRT P- TRT P+ AC (N) AC (L) J904 5V GND +15V GND GND -15V 6.B POUTE 7.B ZOU T 6.B PIN E 7.B ZIN Fig B-42: Interconnection Diagram of NQE-3141-4A TO DISPLAY1 NCD-4990 TB4201 14.PWR OU T 15.PWR OU T E 13.RWR INE 12.PWR IN 11.MTR INE 10.
PAGE 120
JMA-9100 Instruction Manual > B.DRAWINGS > B.
PAGE 121
Appendix C Menu Index Menu Index C.1 Main ....................................................................................................... C-1 C.2 PI ............................................................................................................ C-5 C.3 TT ........................................................................................................... C-7 C.4 AIS ......................................................................................................... C-8 C.
PAGE 122
PAGE 123
JMA-9100 Instruction Manual C.1 > C.Menu Index > C.1 Main Main ├ │ │ │ │ ├ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ 1. EBL Maneuver Setting - - - - - - - - - - - - - - - - ├ 1. EBL Maneuver ├ 2. Reach ├ 3. Turn Mode └ 4. Turn Set 2. File Manager - - - - - - - - - - - - - - - - - - - - 3. RADAR Menu ├ 1. Process Setting - - - - - - - - - - - - - - - │ ├ 1. Video Latitude - - - - - - - - - - - - │ ├ 2.
PAGE 124
JMA-9100 Instruction Manual │ │ │ │ │ │ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ │ │ │ │ │ │ │ │ ├ │ │ │ │ │ │ │ │ │ │ │ 4. 5. 6. 7. > C.Menu Index > C.1 Main │ └ 6. Max Interval - - - - - - - └ 3. TXRX Setting │ ├ 1. PRF Fine Tuning - - - - │ ├ 2. Stagger Trigger - - - - - │ ├ 4. PRF - - - - - - - - - - - │ └ 5. Ice Class Standby Mode - Multi Window Setting ├ 1. DIR/DIST EXP Display- - - - - - ├ 2. Numeric NAV INFO - - - - - - - ├ 3.
PAGE 125
JMA-9100 Instruction Manual │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ │ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ 3. EBL/VRM/PI │ └ 4. Own Symbol/HL/Vector ├ 2. Brilliance Setting- - - - - - - - │ ├ 1. RADAR Video - - - - - │ ├ 2. RADAR Trails │ ├ 3. Target Symbol - - - - - │ ├ 4. Range Rings │ ├ 5. EBL/VRM/PI │ ├ 6. Character │ ├ 7. Own Symbol/HL/Vector │ └ 8. Keyboard ├ 3. User Setting │ ├ 1. Load User Setting - - - │ ├ 2.
PAGE 126
JMA-9100 Instruction Manual │ │ │ │ │ │ │ │ │ └ > C.Menu Index │ │ ├ 3. │ │ │ ├ 4. ├ 5. └ 6. 0. EXIT > C.1 Main ├ 7. Pattern 7 └ 8. Pattern 8 Keyboard Test- - ├ 1. Key Test ├ 2. Buzzer Test └ 3. Light Test MON Display - - System Alarm Log System Information - - - - - - - - - - - - - - - - - - - - - - section 8.3.1.3 on page 8-9 - - - - - - - - - - - - - - - - - - - - - section 8.3.1.4 on page 8-10 - - - - - - - - - - - - - - - - - - - - - section 8.3.1.
PAGE 127
JMA-9100 Instruction Manual C.2 > C.Menu Index > C.2 PI PI ├ ├ │ │ │ │ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ ├ ├ ├ ├ ├ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ ├ 1. Display for All Lines - - - - - - - - 2. Operation Mode - - - - - - - - - - ├ All ├ Individual ├ Track └ Equiangular 3.
PAGE 128
JMA-9100 Instruction Manual │ │ │ │ │ │ │ │ ├ └ > C.Menu Index > C.2 PI ├ 1. Index Line 1 ├ 2. Index Line 2 ├ 3. Index Line 3 ├ 4. Index Line 4 ├ 5. Index Line 5 ├ 6. Index Line 6 ├ 7. Index Line 7 └ 8. Index Line 8 8. Press EBL Dial to Control PI#ii 9.
PAGE 129
JMA-9100 Instruction Manual C.3 > C.Menu Index > C.3 TT TT ├ │ │ │ │ │ │ │ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ │ │ │ │ │ │ │ │ │ │ ├ └ │ │ │ │ 1. Association Setting - - - - - - - ├ 1. Association ├ 2. Proprity ├ 3. Bearing ├ 4. Range ├ 5. Course ├ 6. Speed └ 7. Applicable AIS Target 2. Target Track Setting - - - - - - - ├ 1. Target Track Function - - ├ 2. Target Track Color- - - - │ ├ 1. All │ ├ 2. Target Track No.1 │ ├ 3. Target Track No.2 │ ├ 4.
PAGE 130
JMA-9100 Instruction Manual C.4 > C.Menu Index > C.4 AIS AIS ├ │ │ │ │ │ │ │ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ │ │ │ │ │ │ │ │ │ │ ├ │ │ 1. Association Setting - - - - - - - ├ 1. Association ├ 2. Proprity ├ 3. Bearing ├ 4. Range ├ 5. Course ├ 6. Speed └ 7. Applicable AIS Target 2. Target Track Setting - - - - - - - ├ 1. Target Track Function - - ├ 2. Target Track Color- - - - │ ├ 1. All │ ├ 2. Target Track No.1 │ ├ 3. Target Track No.2 │ ├ 4.
PAGE 131
JMA-9100 Instruction Manual │ │ │ ├ ├ │ │ ├ │ │ ├ └ C.5 5. 6. 7. 8. 9. ├ 3. Filter Display - - - ├ 4. ENT └ 6. Filter Mode - - - - Target Number Display - - AIS Alarm Setting - - - - - ├ 1. Lost Alarm- - - - - └ 2. CPA/TCPA Alarm - Message - - - - - - - - - ├ 1. Addressed Message └ 2. Broadcast Message Display Lost TGT Data - - Own Ship's AIS Data - - - - > C.Menu Index > C.5 AZ - - - - - - - - - - - - - - - - - - - - section 5.3.7.
PAGE 132
JMA-9100 Instruction Manual C.6 > C.Menu Index > C.6 Track Track ├ │ │ │ │ │ │ │ │ ├ ├ ├ ├ │ │ │ │ │ │ ├ │ │ │ │ │ │ ├ │ │ │ │ │ │ ├ │ │ │ │ 1. DISP Own Track Color - - - - - ├ 1. All ├ 2. White ├ 3. Cyan ├ 4. Blue ├ 5. Green ├ 6. Yellow ├ 7. Pink └ 8. Red 2. Clear Own Track Color - - - - - 3. Track Type - - - - - - - - - - - 4. Num/Vector Display - - - - - - - 5. File Operations ├ 1. Select Card Slot ├ 2. Load Mode ├ 3. Load ├ 4. Save ├ 5. Erase └ 6. Card Own Track Display 6.
PAGE 133
JMA-9100 Instruction Manual C.7 > C.Menu Index > C.7 Route Route ├ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ │ │ │ │ │ │ ├ │ │ │ │ 1. Select Route - - - - - - - - - - - - 2. WPT/Route Settig ├ 1. Waypoint Alarm - - - - - - - ├ 2. Route Alarm - - - - - - - - - ├ 3. Set Route Sequence- - - - - │ ├ 1. Planned Speed - - - │ ├ 2. Add - - - - - - - - - │ ├ 3. Correct Position - - - │ ├ 4. Correct Planned Speed │ ├ 5. Delete - - - - - - - - │ ├ 6. Insert - - - - - - - - │ └ 7. New Monitor Route - ├ 6.
PAGE 134
JMA-9100 Instruction Manual C.8 > C.Menu Index > C.8 U.Map U.Map ├ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ ├ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ 1. Own Ship Position - - - - - - - - - - - - - - - 2. Edit User Map - - - - - - - - - - - - - - - - - ├ 1. Make with Cursor - - - - - - - - - - - │ ├ 1. Type │ └ 2. Color ├ 2. Make with L/L - - - - - - - - - - - - - │ ├ 1. Type │ ├ 2. Color │ ├ 3. L/L │ ├ 4. Comment │ ├ 5. Enter │ └ 9. New Line Input/9.
PAGE 135
JMA-9100 Instruction Manual │ │ │ │ │ │ ├ └ │ │ │ │ │ │ │ │ ├ 5. Green │ ├ 6. Yellow │ ├ 7. Pink │ └ 8. Red ├ 3. Mark Size - - - - └ 4. Comment Font Size 6. Geodetic - - - - - - - - 7. File Operations - - - - - ├ ├ ├ ├ ├ ├ └ 1. 2. 3. 4. 5. 6. 7. Select Card Slot Load Mode - - - Load - - - - - - Unload - - - - - Save - - - - - - Erase - - - - - - Card Mark Display - > C.Menu Index > C.8 U.Map - - - - - - - - - - - - - - - - - - - - - section 3.6.2.3 section 3.6.2.4 - section 3.
PAGE 136
JMA-9100 Instruction Manual C.9 > C.Menu Index > C.9 Serviceman Menu Serviceman Menu ├ Serviceman Menu - - - - - - - - - - - - - - - - - ├ 1. Adjust Menu │ ├ 1. Tune Adjustment - - - - - - - - - - - │ ├ 2. Bearing Adjustment - - - - - - - - - - │ ├ 3. Range Adjustment - - - - - - - - - - - │ └ 4. TXRX Adjustment │ │ ├ 1. Antenna Height - - - - - - - - │ │ ├ 2. Tune Peak Adjustment- - - - - │ │ ├ 3. Tune Indicator Adjust - - - - - │ │ ├ 4. MON Adjustment - - - - - - - │ │ ├ 5.
PAGE 137
JMA-9100 Instruction Manual │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ │ ├ 2. TLL(TT) │ ├ 3. TTD(TT) │ ├ 4. TLB(TT) │ ├ 5. OSD │ ├ 6. RSD │ ├ 7. ALR │ ├ 8. ACK │ ├ 9. Next │ ├ 1. TTM(AIS) │ ├ 2. TLL(AIS) │ ├ 3. TTD(AIS) │ ├ 4. TLB(AIS) │ ├ 5. Remote Maintenance │ ├ 6.
PAGE 138
JMA-9100 Instruction Manual │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ ├ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ │ └ │ │ │ │ │ │ │ │ │ │ │ │ │ > C.Menu Index > C.9 Serviceman Menu │ ├ 1. ISW Install │ ├ 2. Mask Setting │ │ ├ 1. No.1 Connection/No.1 Master │ │ ├ 2. No.2 Connection/No.2 Master │ │ ├ 3. No.3 Connection/No.3 Master │ │ ├ 4. No.4 Connection/No.4 Master │ │ ├ 5. No.5 Connection/No.5 Master1 │ │ ├ 6. No.6 Connection/No.6 Masteri │ │ ├ 7. No.7 Connection/No.7 Masteri │ │ └ 8. No.
PAGE 139
PAGE 140
JMA-9133-SA JMA-9132-SA JMA-9123-7XA/9XA JMA-9122-6XA/9XA/6XAH JMA-9110-6XA/6XAH MARINE RADAR EQUIPMENT INSTRUCTION MANUAL For further information,contact: Not use the asbestos URL http://www.jrc.co.jp Marine Service Department Telephone : +81-3-3492-1305 +81-3-3779-1420 Facsimile : tmsc@jrc.co.jp e-mail : AMSTERDAM Branch Telephone : +31-20-658-0750 +31-20-658-0755 Facsimile : service@jrcams.