User's Manual

ManualsBrandsJapan Radio ManualsElectronicsMarine Radar

MARINE RADAR EQUIPMENT

INSTRUCTION MANUAL

JMA-9133-SA JMA-9132-SA

JMA-9123-7XA/9XA

JMA-9122-6XA/9XA/6XAH

JMA-9110-6XA/6XAH

MARINE RADARMARINE RADAR

EQUIPMENTEQUIPMENT

INSTRUCTIONINSTRUCTION

MANUALMANUAL

JMA-9133-SAJMA-9133-SA

JMA-9132-SAJMA-9132-SA

JMA-9123-7XA/9XAJMA-9123-7XA/9XA

JMA-9122-6XA/9XA/6XAHJMA-9122-6XA/9XA/6XAH

JMA-9110-6XA/6XAHJMA-9110-6XA/6XAH

01ETM

ISO 9001, ISO 14001 Certified

Printed in Japan

Marine Service Department

+81-3-3492-1305

+81-3-3779-1420

tmsc@jrc.co.jp

Telephone :

Facsimile :

e-mail :

AMSTERDAM Branch

Telephone :

Facsimile :

e-mail :

+31-20-658-0750

+31-20-658-0755

service@jrcams.nl

SEATTLE Branch

Telephone :

Facsimile :

e-mail :

+1-206-654-5644

+1-206-654-7030

service@jrcamerica.com

CODE No.7ZPRD0685CODE No.7ZPRD0685

MAR. 2008 Edition 1 JRCMAR. 2008 Edition 1 JRC

Not use the asbestos

For further information,contact:

URL http://www.jrc.co.jp

Summary of content (280 pages)

PAGE 1
JMA-9133-SA JMA-9132-SA JMA-9123-7XA/9XA JMA-9122-6XA/9XA/6XAH JMA-9110-6XA/6XAH MARINE RADAR EQUIPMENT INSTRUCTION MANUAL For further information,contact: Not use the asbestos URL http://www.jrc.co.jp Marine Service Department Telephone : +81-3-3492-1305 +81-3-3779-1420 Facsimile : tmsc@jrc.co.jp e-mail : AMSTERDAM Branch Telephone : +31-20-658-0750 +31-20-658-0755 Facsimile : service@jrcams.
PAGE 2
PAGE 3
◆◆◆ PRECAUTIONS BEFORE OPERATION ◆◆◆ ■ Cautions for high voltage High voltages from hundreds volts to tens of thousands volts are to be applied to the electronic equipment such radio and radar devices. You do not face any danger during normal operation, but sufficient cares are required for maintenance, inspection and adjustment of their internal components. (Maintenance, check-up and adjustment of the inside of the equipment are prohibited except by maintenance specialists.
PAGE 4
◆◆◆ FIRST-AID TREATMENTS ◆◆◆ ☆ First-aid treatments As far as the victim of electric shock is not in dangerous condition, do not move him and practice artificial respiration on him immediately. Once started, it should be continued rhythmically. (1) Do not touch the victim confusedly as a result of the accident, but the rescuer may also get an electric shock. (2) Turn off the power source calmly and move the victim away quietly from the electric line.
PAGE 5
☆ When pulse is beating but breathing has stopped (Mouth-to-mouth respiration) Fig 1. (1) Tilt the victim's head back as far as this face looks back. (A pillow may be inserted his neck.) (2) Push his jaw upward to open his throat wide (to spread his airway). (3) Pinch the victim's nostrils and take a deep breath, block his mouth completely with yours and blow into his mouth strongly. Take a deep breath again and blow into his mouth. Continue this 10 to 15 times a minutes (blocking his nostrils).
PAGE 6
☆ When both pulse and breathing have stopped Perform the (Cardiac massage) Fig 2. and (Mouth-to-mouth respiration) Fig 1. When no pulse has come not to be felt, his pupils are open and no heartbeat is heard, cardiac arrest is supposed to have occurred and artificial respiration must be performed.
PAGE 7
PREFACE Thank you very much for purchasing the JRC marine radar equipment, JMA-9100 series. This equipment is a marine radar equipment designed to obtain safe operation of marine ships. This equipment consists of a radar signal transmitter-receiver unit, a LCD display unit and a scanner unit as its main units. • Before operating the equipment, be sure to read this instruction manual carefully for correct operation. • Maintain this instruction manual so that operators can refer to it at anytime.
PAGE 8
● Before Operation ● Pictorial Indication Various pictorial indications are included in this manual and are shown on these equipment so that you can operate them safety and correctly and prevent any danger to you and/or to other persons and any damage to your property during operation. Such indications and their meanings are as follows. Please understand them before you read this manual: This indication is shown where incorrect equipment operation due to negligence may cause death or serious injuries.
PAGE 9
● PRECAUTIONS ● Never conduct inspection or repair work of equipment components. Inspection or repair work by uncertified personnel may result in fire hazard or electrocution. For inspection and repair work of equipment components, consult with our branch office, branch shop, sales office, or our distributor in your district. ! When conducting maintenance, make sure to turn the main power off.Failure to comply may result in electrocution. ! Turn off the main power before cleaning the equipment.
PAGE 10
! Make sure to turn off the scanner safety switch. Failure to comply may result in injuries caused by physical contact with the rotating scanner. Never directly touch the internal components of the scanner or indicator. Direct contact with these highvoltage components may cause electrocution. For maintenance, inspection, or adjustment of equipment components, consult with our branch office, branch shop, sales office, or our distributor in your district.
PAGE 11
Microwave radiation level: Keep out from a distance closer than that specified below for each type of scanner when it is transmitting. Being within the specified distance from the center of the front face of the scanner may cause microwave exposure which could result in injuries (especially of the eyes). NKE-2103 (radiation levels: 10 W/m2): 0.6 m NKE-2254 (radiation levels: 10 W/m2): 0.6 m NKE-1125/1129 (radiation levels: 10 W/m2): 0.7m NKE-1130/1139 (radiation levels: 10 W/m2): 1.
PAGE 12
When cleaning the display screen, do not wipe it too strongly with a dry cloth. Also, do not use gasoline or thinner to clean the screen. Failure to comply will result in damage to the screen surface. ! Do not change MBS Level/Area unless absolutely necessary. ! When disposing of used lithium batteries, be sure to insulate the batteries by attaching a piece of adhesive tape on the + and - terminals. Failure to comply may cause heat generation, explosion, or fire when the batteries get shorted out.
PAGE 13
! Use Target Tracking (TT) function only as a navigation aid. The final navigation decision must always be made by the operator him/herself. Making the final navigation decision based only on tracking target information may cause accidents. Tracking target information such as vector, target numerical data, and alarms may contain some errors. Also, targets that are not detected by the radar cannot be acquired or tracked.
PAGE 14
! When setting a guard zone, make sure to properly adjust gain, sea-surface reflection suppression level, and rain/ snow reflection suppression level so that the optimal target images are always on the radar screen. The guard zone alarm will not be activated for targets undetected by the radar, and it may result in accidents such as collisions. ! The simulation function is used exclusively for deciding whether or not target tracking is properly operating.
PAGE 15
! Make sure to take off your watch when your hand must get close to the magnetron. ! Make sure that two or more staff member work together when replacing the LCD. If only one person attempts to replace the LCD, he/she may drop it and become injured. Failure to comply may result in damage to the watch since the magnetron is a strong magnet.
PAGE 16
Do not change the quantization level settings unless absolutely necessary. If set at an inappropriate value, the target acquisition or target tracking function deteriorates, and this may lead to accidents.
PAGE 17
The Mounting Point of the Warning Label Warning Label NCD-4990 Display Unit Warning Label Front face Back face NWZ-170 Monitor Unit xv
PAGE 18
Warning Label NDC-1399-9 Radar Process Unit (Desktop Type) Warning Label NBA-5135 AC/DC Converter (Desktop Type) xvi
PAGE 19
Warning Label NQE-3141-4A/8A Interswitch Unit Warning Label NQE-3167 Power Control Unit xvii
PAGE 20
Warning La NKE-2103-6/6HS Scanner Unit Warning NKE-1129-7/9 Scanner Unit NKE-1125-6/9 Scanner Unit NKE-2254-6HS Scanner Unit xviii
PAGE 21
Warning Label NKE-1139/1130 Scanner Unit Warning Label NTG-3230/3225 Transmitter Receiver Unit xix
PAGE 22
EQUIPMENT APPEARANCE Scanner Unit Type NKE-1130 (12 feet) Scanner Unit Type NKE-1139 (12 feet) Transmitter Receiver Unit Type NTG-3230(30kW) xx
PAGE 23
Scanner Unit Type NKE-1129-7 (7 feet) Scanner Unit Type NKE-1129-9 (9 feet) Transmitter Receiver Unit Type NTG-3225(25kW) xxi
PAGE 24
Scanner Unit Type NKE-1125-6 (6 feet) Scanner Unit Type NKE-1125-9 (9 feet) Scanner Unit Type NKE-2254-6HS (6 feet) xxii
PAGE 25
Scanner Unit Type NKE-2103-6 (6 feet) Scanner Unit Type NKE-2103-6HS (6 feet) Power Control Unit Type NQE-3167 xxiii
PAGE 26
Display Unit Type NCD-4990 (Stand alone type) Interswitch Unit Type NQE-3141-4A xxiv
PAGE 27
Monitor Unit Type NWZ-170 (Desktop type) Operation Unit Type NCE-5163 (Desktop type) Radar Process Unit Type NDC-1399-9 (Desktop type) DISPLAY UNIT TYPE NCD-4990T (DESKTOP TYPE) xxv
PAGE 28
GLOSSARY This section describes the main terms used for this equipment and general related maritime terms. A AZ Acquisition/Activation zone A zone set up by the operator in which the system should automatically acquire radar targets and activate reported AIS targets when entering the zone. Activated target A target representing the automatic or manual activation of a sleeping target for the display of additional information.
PAGE 29
CPA/TCPA The distance to the Closest Point of Approach/Time to the Closest Point of Approach. Limits are set by the operator and are related to own ship. CTW Course Through Water The direction of the ship's movement through the water D DRIFT The current velocity for manual correction or the current speed on the horizontal axis of the 2-axis log is displayed. E EBL Electronic Bearing Line An electronic bearing line originated from own ship's position.
PAGE 30
Lost AIS target A target symbol representing the last valid position of an AIS target before the reception of its data was lost, or its last dead-reckoned position. Lost tracked target One for which target information is no longer available due to poor, lost or obscured signals.
PAGE 31
RM Relative Motion A display on which the position of own ship remains fixed, and all targets move relative to own ship. RM(R) Relative Motion. Relative Trails. RM(T) Relative Motion. True Trails. ROT Rate Of Turn Change of heading per time unit. Route A set of waypoints. RR Range Rings S SART Search And Rescue Transponder Radar transponder capable of operating in the 9GHz band Sea stabilization A display mode in which speed and course information are referred to the sea.
PAGE 32
Trial manoeuvre A graphical simulation facility used to assist the operator to perform a proposed maneuver for navigation and collision avoidance purposes. True course The direction of motion relative to ground or to sea, of a target expressed as an angular displacement from north True speed The speed of a target relative to ground, or to sea True vector A vector representing the predicted true motion of a target, showing course and speed with reference to the ground or sea TT Target Tracking.
PAGE 33
Index ◆◆◆ PRECAUTIONS BEFORE OPERATION ◆◆◆ .............................................. i ◆◆◆ FIRST-AID TREATMENTS ◆◆◆ .................................................................. ii PREFACE ................................................................................................................... v The Mounting Point of the Warning Label ................................................................. xv EQUIPMENT APPEARANCE .................................................................
PAGE 34
3.2.7 Reset Alarm Buzzer [ALARM ACK] .............................................3-12 3.2.8 To get the appropriate image that targets can be easily observed 3.3 ............3-13 OPERATION PROCEDURES ..............................................................3-14 3.3.1 Move Cross Cursor Mark by Trackball ........................................3-14 3.3.2 Operate Software Buttons ...........................................................3-15 3.3.3 Basic Menu Operation ........................
PAGE 35
3.6 DISPLAY USER MAP ...........................................................................3-47 3.6.1 Create User Map (Mark/Line) ........................................................3-47 3.6.2 Set User Map Display (Mark Display Setting) .............................3-50 3.6.3 Edit User Map (Edit User Map) .....................................................3-52 3.6.4 Correct Position on User Map (Shift User Map) .........................3-60 3.6.5 Save User Map .........................
PAGE 36
3.11 USING CARD .....................................................................................3-120 3.11.1 Operate File on the Card (File Manager) ...................................3-120 SECTION 4 MEASUREMENT OF RANGE AND BEARING 4.1 USE OF NAVIGATION TOOLS ..............................................................4-1 4.1.1 Using Cursor (Cursor) ....................................................................4-2 4.1.2 Using Range Rings (Range Rings) .................................
PAGE 37
5.3 AIS OPERATION ..................................................................................5-26 5.3.1 Restrictions ....................................................................................5-26 5.3.2 Setting AIS Display Function (AIS Function) ..............................5-26 5.3.3 Activate AIS Targets (Activate AIS) .............................................5-27 5.3.4 Deactivate AIS Targets (Deactivate AIS) .....................................5-27 5.3.
PAGE 38
SECTION 7 SETTINGS FOR SYSTEM OPERATION 7.1 SETTINGS AT INSTALLATION .............................................................7-1 7.1.1 How to Open the Serviceman Menu（Service Man Menu）.........7-1 7.1.2 GYRO I/F Setting .............................................................................7-2 7.1.3 Tuning (Tune Adjustment) .............................................................7-5 7.1.4 Bearing Adjustment ........................................................................
PAGE 39
8.1 ROUTINE MAINTENANCE ....................................................................8-1 8.2 MAINTENANCE ON EACH UNIT ...........................................................8-2 8.2.1 Scanner Unit NKE-1125/1129/1130/1139/2103/2254 ....................8-2 8.2.2 Wave Guide Tube (JMA-9123-7XA/9XA) ........................................8-4 8.2.3 Coaxial Cable (JMA-9133-SA) ........................................................8-4 8.2.4 Transmitter Receiver Unit (NTG-3225/3230) .........
PAGE 40
10.5 ABOUT THE CHINA ROHS .................................................................10-3 SECTION 11 SPECIFICATION 11.1 JMA-9133-SA TYPE RADAR ...............................................................11-1 11.2 JMA-9132-SA TYPE RADAR ............................................................... 11-2 11.3 JMA-9123-7XA/9XA TYPE RADAR ....................................................11-3 11.4 JMA-9122-6XA/9XA TYPE RADAR ....................................................11-4 11.
PAGE 41
A.2.4 Change of Connection Pattern (with 3 or More Display Units) .. A-7 A.2.5 Operating Connection Pattern Files (File Operations) ............... A-8 A.2.6 Names of Display Units and Scanner Units ................................. A-9 A.3 REFERENCE ....................................................................................... A-10 A.3.1 Preheat Time after Change of Connection Pattern ................... A-10 A.3.2 Notes on Changing Connection Pattern ...................................
PAGE 42
B.6.7 NTG-3225 ...................................................................................... B-26 B.6.8 NKE-1130 (AC110V) ...................................................................... B-27 B.6.9 NKE-1130 (AC220V) ...................................................................... B-28 B.6.10 NKE-1139 (AC110V) ...................................................................... B-29 B.6.11 NKE-1139 (AC220V) ......................................................................
PAGE 43
1 GENERAL AND EQUIPMENT COMPOSITION 1 2 NAMES AND FUNCTIONS OF CONTROL PANEL KEYS AND FUNCTIONS OF SOFTWARE BUTTONS 2 3 BASIC OPERATION 3 4 MEASUREMENT OF RANGE AND BEARING 4 5 OPERATION OF TARGET TRACKING AND AIS 5 6 TRUE AND FALSE ECHOES ON DISPLAY 6 7 SETTINGS FOR SYSTEM OPERATION 7 8 COUNTERMEASURES FOR TROUBLE AND ADJUSTMENT 8 9 TROUBLE SHOOTING AND AFTER-SALES SERVICE 9 10 DISPOSAL 10 11 SPECIFICATIONS 11 Appendix A
PAGE 44
PAGE 45
SECTION 1 GENERAL AND EQUIPMENT COMPOSITION GENERAL AND EQUIPMENT COMPOSITION 1.1 FUNCTIONS ...........................................................................................1-1 1.1.1 Function of This System .................................................................1-1 1.2 FEATURES .............................................................................................1-2 1.3 CONFIGURATION ..................................................................................1-4 1.
PAGE 46
PAGE 47
JMA-9100 Instruction Manual 1.1 > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.1 FUNCTIONS FUNCTIONS This equipment is a high-performance radar equipment consisting of a scanner unit, a transmitter-receiver unit and a high resolution color LCD display unit. This equipment complies with the performance standard of IMO. 1.1.1 Function of This System The JMA-9100 series is a color radar system designed to comply with the international standards of the IMO.
PAGE 48
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.2 FEATURES 1.2 FEATURES Realization of Large, Easy-to-see Screen with High Resolution The 23.1-inch color LCD with high resolution of 1600x1200 pixels can display radar images of 320 mm or more in diameter. Even short-range targets can also be displayed as high-resolution images.
PAGE 49
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.2 FEATURES Improved Day/Night Mode Five types of background colors are available in Day/Dusk/Night mode (total 5 background colors). Each background color can be reproduced to be suited for the user's operating environment by simple key operation. The radar echoes and a variety of graphics can also be represented in different colors, ensuring easy-tosee displays.
PAGE 50
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.3 CONFIGURATION 1.
PAGE 51
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.3 CONFIGURATION Notes: 1) The drive motor for the scanner unit is available in AC100-115V or AC220-240V type for NKE-1139/1130/1125/1129 series. Please specify the motor type when ordering. 2) The motor of NKE-2254/2103 can operate under both AC100-115V and AC220-240V, then need not to specify the motor type. 3) When using NKE-2254/2103, they need AC/DC Converter Unit NBA-5135 (Option) in display unit.
PAGE 52
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.4 EXTERIOR DRAWINGS 1.
PAGE 53
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 54
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 55
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 56
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 57
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 58
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 59
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 60
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 61
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 62
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 63
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 64
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 65
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 66
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 67
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 68
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 69
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 70
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 71
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 72
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.5 GENERAL SYSTEM DIAGRAMS 1.
PAGE 73
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.5 GENERAL SYSTEM DIAGRAMS 1 NKE-1139 SCANNER UNIT NJU-84 PERFORMANCE UNIT CIRCUIT BREAKER (SHIP YARD SUPPLY) (5A) AC100V,60Hz 1φ,200 W ( W I T H P M U N I T) 0 . 6 /1 k V - D P Y C Y S- 1 .
PAGE 74
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.5 GENERAL SYSTEM DIAGRAMS NKE-1130 SCANNER UNIT NJU-84 PERFORMANCE UNIT CIRCUIT BREAKER (SHIP YARD SUPPLY) (5A) AC100V,60Hz 1φ,200 W ( W I T H P M U N I T) 0. 6 /1 k V - D P Y C Y S- 1 .5 NBL-175 SHIP’S MAIN STEPDOWN TRANSFORMER for HEATER AC220V,60Hz,1φ 1 4 CO RE S CO MP O S ITE CA B LE H -2 6 9 5 1 1 0 0 5 6 M A X 2 3 φ ( J R C S U P P L Y) NCD-4990 DISPLAY UNIT GYRO LOG (NMEA 0183) DGPS VDR RADAR(INTER SWITCH) 0 .
PAGE 75
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.5 GENERAL SYSTEM DIAGRAMS 1 NKE-1129-7 SCANNER UNIT NJU-85 PERFORMANCE UNIT CIRCUIT BREAKER (SHIP YARD SUPPLY) (5A) AC100V,60Hz 1φ,200 W ( W I T H P M U N I T) 0 .6 /1 k V - D P Y C Y S- 1 .
PAGE 76
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.5 GENERAL SYSTEM DIAGRAMS NKE-1129-9 SCANNER UNIT NJU-85 PERFORMANCE UNIT CIRCUIT BREAKER (SHIP YARD SUPPLY) (5A) AC100V,60Hz 1φ,200 W ( W I T H P M U N I T) 0. 6 / 1 k V - D P Y C Y S- 1 .
PAGE 77
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.5 GENERAL SYSTEM DIAGRAMS 1 NKE-1125-6 SCANNER UNIT NJU-85 PERFORMANCE UNIT CIRCUIT BREAKER (SHIP YARD SUPPLY) (5A) AC100V,60Hz 1φ,200 W ( W I T H P M U N I T) 0 .6 /1 k V - D P Y C Y S- 1 .5 NBL-175 STEPDOWN TRANSFORMER SHIP’S MAIN for HEATER AC220V,60Hz,1φ 1 4 CO RE S CO MP O S ITE CA B L E H -2 6 9 5 1 1 0 0 5 6 M A X 2 3 φ ( J R C S U P P L Y) NCD-4990 DISPLAY UNIT GYRO LOG (NMEA 0183) DGPS VDR RADAR(INTER SWITCH) 0 .
PAGE 78
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.5 GENERAL SYSTEM DIAGRAMS NKE-1125-9 SCANNER UNIT NJU-85 PERFORMANCE UNIT CIRCUIT BREAKER (SHIP YARD SUPPLY) (5A) AC100V,60Hz 1φ,200 W ( W I T H P M U N I T) 0. 6 /1 k V - D P Y C Y S- 1 .5 NBL-175 SHIP’S MAIN STEPDOWN TRANSFORMER for HEATER AC220V,60Hz,1φ 1 4 CO RE S CO MP O S ITE CA B LE H -2 6 9 5 1 1 0 0 5 6 M A X 2 3 φ ( J R C S U P P L Y) NCD-4990 DISPLAY UNIT GYRO LOG (NMEA 0183) DGPS VDR RADAR(INTER SWITCH) 0 .
PAGE 79
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.5 GENERAL SYSTEM DIAGRAMS 1 NKE-2254-6HS SCANNER UNIT NJU-85 PERFORMANCE UNIT CIRCUIT BREAKER (SHIP YARD SUPPLY) (5A) AC100V,60Hz 1φ,200 W ( W I T H P M U N I T) 0 .6 /1 k V - D P Y C Y S- 1 .5 NBL-175 STEPDOWN TRANSFORMER SHIP’S MAIN for HEATER AC220V,60Hz,1φ 1 4 CO RE S CO MP O S ITE CA B L E H -2 6 9 5 1 1 0 0 5 6 M A X 2 3 φ ( J R C S U P P L Y) NCD-4990 DISPLAY UNIT GYRO LOG (NMEA 0183) DGPS VDR RADAR(INTER SWITCH) 0 .
PAGE 80
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.5 GENERAL SYSTEM DIAGRAMS NKE-2103-6 SCANNER UNIT NJU-85 PERFORMANCE UNIT 1 9 CO RE S CO MP O S ITE CA B L E C F Q - 6 9 1 2- * * M A X 1 4 . 5 φ ( J R C S U P P L Y) NCD-4990 DISPLAY UNIT GYRO LOG(NMEA 0183) DGPS VDR RADAR(INTER SWITCH) 0. 6/1k V- DPYC Y - 6 250 V- MPYCYS - 7 SHIP’S MAIN AC220 V,60Hz,1φ,800VA 250 V- T T YC S - 1 250 V- T T YC S - 1 0. 6/1k V- DPYC YS - 1.
PAGE 81
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.5 GENERAL SYSTEM DIAGRAMS 1 NKE-2103-6HS SCANNER UNIT NJU-85 PERFORMANCE UNIT 1 9 CO RE S CO MP O S ITE CA B L E C F Q - 6 9 1 2- * * M A X 1 4 . 5 φ ( J R C S U P P L Y) NCD-4990 DISPLAY UNIT GYRO LOG(NMEA 0183) DGPS VDR RADAR(INTER SWITCH) 0. 6/1k V- DPYC Y - 6 250 V- MPYCYS - 7 SHIP’S MAIN AC220V,60Hz,1φ,800 VA 250 V- T T YC S - 1 250 V- T T YC S - 1 0. 6/1k V- DPYC YS - 1.
PAGE 82
JMA-9100 Instruction Manual > 1.GENERAL AND EQUIPMENT COMPOSITION > 1.
PAGE 83
SECTION 2 NAMES AND FUNCTIONS OF CONTROL PANEL KEYS AND FUNCTIONS OF SOFTWARE BUTTONS NAMES AND FUNCTIONS OF CONTROL PANEL KEYS AND FUNCTIONS OF SOFTWARE BUTTONS 2.1 2.2 2.3 NAMES OF DISPLAY .............................................................................2-1 NAMES AND FUNCTIONS OF CONTROL PANEL KEYS ..................2-11 FUNCTIONS OF SOFTWARE BUTTONS ...........................................
PAGE 84
PAGE 85
JMA-9100 Instruction Manual 2.1 > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.1 NAMES OF DISPLAY NAMES OF DISPLAY 2 Example of screen display In this example, the screen is divided into a number of areas and the names in each area are indicated.
PAGE 86
JMA-9100 Instruction Manual > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.
PAGE 87
JMA-9100 Instruction Manual > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.
PAGE 88
JMA-9100 Instruction Manual > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.
PAGE 89
JMA-9100 Instruction Manual > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.
PAGE 90
JMA-9100 Instruction Manual > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.
PAGE 91
JMA-9100 Instruction Manual > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.
PAGE 92
JMA-9100 Instruction Manual > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.
PAGE 93
JMA-9100 Instruction Manual > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.
PAGE 94
JMA-9100 Instruction Manual > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.1 NAMES OF DISPLAY Alarm Alarm indication (The system alarm indicated in red . Other information indicated in blue or yellow.
PAGE 95
JMA-9100 Instruction Manual 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.2 NAMES AND FUNCTIONS OF CONTROL PANEL KEYS NAMES AND FUNCTIONS OF CONTROL PANEL KEYS 13 VRM1 2 1 27 OPTION OPTION 25 USER PANEL EBL2 EBL1 POWER 24 12 11 ALARM ACK TX STBY 10 4 3 PWR FAIL PWR ACK 2 20 5 TUNE 21 AIS/AR PA DAY NIGHT 26 22 DATA OFF CANCEL MANUAL HL OFF ACQ ACQ TGT DATA T/R VECT RAIN 17 6 16 18 7 SEA 19 23 8 GAIN 15 VRM2 14 9 RANGE 29 28 30 2 1 2.
PAGE 96
JMA-9100 Instruction Manual CONTROL PANEL KEYS 1 > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.2 NAMES AND FUNCTIONS OF [POWER] (Power supply) switch The lamp is lit and the equipment is activated. If this switch is pressed while the equipment is running, the power of the equipment is shut down. → 3.1.1 on page 3-2 2 [PWR ACK] (Power alarm acknowledgement) key Use this function to acknowledge the alarm when power supply abnormality occurs.
PAGE 97
JMA-9100 Instruction Manual 8 > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.2 NAMES AND FUNCTIONS OF CONTROL PANEL KEYS [GAIN] (Gain/pulse length) dial This function adjusts the reception sensitivity of the radar. To increase the sensitivity, turn the dial clockwise. The transmission pulse width can be switched by pressing the dial. gain→ 3.2.4 on page 3-8 pulse width →3.4.2 on page 3-24 9 [RANGE ＋／－] (Range switching) key This function switches the range. Press [+] to increase the observation range.
PAGE 98
JMA-9100 Instruction Manual CONTROL PANEL KEYS 15 > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.2 NAMES AND FUNCTIONS OF [VRM] (Variable Range Marker) dial This function changes the range of the VRM that is selected by VRM1/2. By pressing the dial, the parallel line cursor function can be switched to Operation → Fixed → Off → Operation.
PAGE 99
JMA-9100 Instruction Manual 23 > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.2 NAMES AND FUNCTIONS OF CONTROL PANEL KEYS [DATA OFF] (DATA Off) key This function sets the graphics other than HL, range ring, EBL, and VRM to OFF temporarily while this key is pressed. → 3.4.11 on page 3-34 24 [PANEL] (Operator panel brilliance) key This function adjusts the lighting brilliance of various switches and dial positions on the operator panel. The brightness changes cyclically whenever this key is pressed.
PAGE 100
JMA-9100 Instruction Manual BUTTONS 2.3 > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.3 FUNCTIONS OF SOFTWARE FUNCTIONS OF SOFTWARE BUTTONS In this radar, the frequently used functions can be directly set from the screen without opening the menu by using the software buttons on the screen for quick handling. The screen is divided into a number of areas and each area is named.
PAGE 101
> JMA-9100 Instruction Manual 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.3 FUNCTIONS OF SOFTWARE BUTTONS Upper left of the display ① Range scale switching ⑦ Transmission pulse length switching ② Range rings display On /Off ③ Motion mode true / relative switching ④ Off center switching ⑤ Transmission / Standby switching ⑧ Azimuth display mode switching ⑥ Interswitch connection change 1 Range scale switching To increase the observation range scale (maximum 96NM), click the range (minimum 0.
PAGE 102
JMA-9100 Instruction Manual BUTTONS 6 > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.3 FUNCTIONS OF SOFTWARE Interswitch connection change This button is displayed when the interswitch is connected. This button indicates the connection status of the scanner unit that is connected to the indicator. If the button is clicked in the transmission standby state, the menu for changing the connection state between the scanner unit and the indicator is displayed.
PAGE 103
JMA-9100 Instruction Manual > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.3 FUNCTIONS OF SOFTWARE BUTTONS Interference rejection (IR) mode switching 2 The interference rejection mode is switched whenever this button is clicked. IR Off IR Low ⇒ ⇒ IR Meddle ⇒ IR High IR Off ⇒ 2 Target enhance (ENH) mode switching 3 The target enhance mode is switched whenever this button is clicked.
PAGE 104
JMA-9100 Instruction Manual BUTTONS > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.
PAGE 105
JMA-9100 Instruction Manual 5 , 6 , 7 > and 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.3 FUNCTIONS OF SOFTWARE BUTTONS EBL1 / 2 and VRM1 / 2 adjustment 8 These functions set the EBL1 , VRM1 , EBL2 , and VRM2 displays to On / Off and acquire the operation right. If the button is clicked on, the operation right is acquired. Make adjustments by moving the track ball to the left and right Determine the adjustment by left-clicking.
PAGE 106
JMA-9100 Instruction Manual BUTTONS > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.3 FUNCTIONS OF SOFTWARE Lower right of the display ③ Own ship's track interval switching ① Mark color switching ④ Own ship's track interval unit switching ② Own ship’s track color switching ⑤ Map display On / Off ⑧ CPA ring display On / Off ⑥ Graphic display Off ⑦ Ship's heading line Off 1 Mark color switching The color of the mark is switched whenever this button is clicked.
PAGE 107
JMA-9100 Instruction Manual 8 > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.3 FUNCTIONS OF SOFTWARE BUTTONS CPA ring display On / Off The CPA ring display is switched to On / Off whenever the button is clicked. When the target vector display mode is On.
PAGE 108
JMA-9100 Instruction Manual BUTTONS > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.
PAGE 109
JMA-9100 Instruction Manual 6 > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.3 FUNCTIONS OF SOFTWARE BUTTONS Past position display interval switching The past position display interval is switched whenever the button is clicked. 7 Past position display interval unit switching The past position display interval unit is switched whenever the button is clicked. min 8 ⇒ NM ⇒ min AIS On / Off The AIS display is switched to On / Off whenever the button is clicked.
PAGE 110
JMA-9100 Instruction Manual BUTTONS > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.3 FUNCTIONS OF SOFTWARE Numeric information: AIS target information simple display ①：Detail / simple display switching ②：Unread message display 1 Detail / simple display switching This function switches the display mode to detail / simple display when AIS target information is displayed. 2 Unread message display When there is an unread message from the AIS target that is displayed, the message is displayed.
PAGE 111
JMA-9100 Instruction Manual > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.3 FUNCTIONS OF SOFTWARE BUTTONS Numeric information: Tracked target information ① Tracked target numeric value indication scroll 1 Tracked target numeric value indication scroll This function scrolls the target numbers that are indicated in the tracked target information.
PAGE 112
JMA-9100 Instruction Manual BUTTONS > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.3 FUNCTIONS OF SOFTWARE Graph information: Wind direction / speed ① Wind direction / speed numeric value indication true / relative switching 1 Wind direction / speed numeric value indication true / relative switching The wind direction / speed numeric value indication is switched to T (true) / R (relative) whenever this button is clicked.
PAGE 113
JMA-9100 Instruction Manual 5 > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.3 FUNCTIONS OF SOFTWARE BUTTONS AIS menu If the button is clicked, the AIS Menu is opened. 6 Route menu 2 If this button is clicked, the Route Menu is opened. 7 Parallel index line menu If this button is clicked, the PI Menu is opened. 8 Automatic acquisition / activation zone menu If this button is clicked, the AZ Menu is opened. 9 User map menu If the button is clicked, the User Map Menu is opened.
PAGE 114
JMA-9100 Instruction Manual BUTTONS 1 > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS > 2.3 FUNCTIONS OF SOFTWARE Display item switching The brilliance adjustment screen and display information setting screen interchange whenever this button is clicked. ⇔ 2 Panel lighting brilliance switching This function enables the setting of the brilliance of the lighting of the control panel. The brilliance changes whenever this button is clicked. Five levels of settings are available.
PAGE 115
JMA-9100 Instruction Manual > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS> 2.3 FUNCTIONS OF SOFTWARE BUTTONS Alarm ① Alarm acknowridgement ② Error log display 1 2 Alarm acknowledgment If this button is clicked, the buzzer sound of the alarm that is currently issued is stopped and the alarm lamp stops blinking. If multiple alarms are issued, the next alarm to be acknowledged is displayed. If the button is clicked, the alarm displayed on the top is acknowledged.
PAGE 116
JMA-9100 Instruction Manual BUTTONS > 2.CONTROL PANEL KEYS and SOFTWARE BUTTONS 2－ 32 > 2.
PAGE 117
SECTION 3 BASIC OPERATION BASIC OPERATION 3.1 OPERATION FLOW ...............................................................................3-1 3.1.1 Power ON and Start the System ....................................................3-2 3.1.2 Observe and Adjust Video ..............................................................3-4 3.1.3 Acquire and Measure Data .............................................................3-4 3.1.4 Display and Measure with Reference to CCRP ............................
PAGE 118
3.3.2 3.3.3 3.3.4 Operate Software Buttons ...........................................................3-15 Basic Menu Operation ..................................................................3-16 Operation on Numeric Value, Latitude / Longitude and Character Input menu .....................................................................................3-17 3.3.5 Overview of Menu Structure .........................................................3-22 3.4 GENERAL RADAR OPERATION .........................
PAGE 119
3.7.5 Method of Using Route .................................................................3-81 3.7.6 Detailed Route Settings ................................................................3-82 3.7.7 Clear Waypoint/Route Data (Clear WPT/Route Data) .................3-86 3.7.8 Operate Route Data File ................................................................3-87 3.8 APPLIED OPERATIONS ......................................................................3-91 3.8.
PAGE 120
PAGE 121
JMA-9100 Instruction Manual 3.1 > 3.BASIC OPERATION > 3.1 OPERATION FLOW OPERATION FLOW Attention • Do not put anything on the operation panel. If you put anything hot on it, it may be deformed. • Do not give any impact to the operation panel, trackball, or controls. Otherwise, any failure or damage may result. POWER ON AND START THE SYSTEM OBSERVE AND ADJUST VIDEO ACQUIRE AND MEASURE DATA END THE OPERATION AND STOP THE SYSTEM Each operation is described in detail below.
PAGE 122
JMA-9100 Instruction Manual 3.1.1 > 3.BASIC OPERATION > 3.1 OPERATION FLOW Power ON and Start the System ! • A malfunction may occur if the power in the ship is instantaneously interrupted during operation of the radar. In this case, the power should be turned on again. Attention • Wait for about 2 seconds before turning on the power again.
PAGE 123
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.1 OPERATION FLOW Procedures 1) Check that the ship’s mains are turned on. 2) Press [POWER] key. The system is turned on, and the preheating time is displayed. Preheat 3) is indicated at the upper left of the radar display. Wait until the preheating time is over. Preheat When the preheating time is over, the preheating time screen disappears, and at the upper left of the radar display changes to . Standby 4) Press [TX/STBY] key.
PAGE 124
JMA-9100 Instruction Manual 3.1.2 > 3.BASIC OPERATION > 3.1 OPERATION FLOW Observe and Adjust Video Procedures 1) 2) Press [RANGE+] key or [RANGE-] key to set the range to the scale required for target observation. [GAIN] [SEA] and [RAIN] to obtain the clearest targets. Refer to [GAIN] dial→ Section 3.2.4 "Adjust Gain [GAIN]" [SEA] dial → Section 3.2.5 "Suppress Sea Clutter [SEA]" [RAIN] dial → Section 3.2.6 "Suppress Rain/Snow Clutter [RAIN]" for how to use each dial.
PAGE 125
JMA-9100 Instruction Manual 3.1.5 > 3.BASIC OPERATION > 3.1 OPERATION FLOW End the Operation and Stop the System Exit 1) Press [TX/STBY] key. The radar will stop transmission and the antenna will stop rotating. Transmit i 2) at the upper left of the radar display changes to Standby . Maintain the standby state if radar observation is restarted in a relatively short time.Only pressing the [TX/STBY] key starts observation. Press [POWER] key. The system will be turned off.
PAGE 126
JMA-9100 Instruction Manual 3.2 3.2.1 > 3.BASIC OPERATION > 3.2 OBSERVE AND ADJUST VIDEO OBSERVE AND ADJUST VIDEO Adjust Monitor Brilliance [BRILL] Procedures 1) Obtain the best-to-see display with optimum brilliance by turning the [BRILL] dial at the lower right of the monitor unit. Turning the [BRILL] dial clockwise increases the brilliance of the entire display. Conversely, turning the [BRILL] dial counterclockwise decreases the brilliance of the entire display.
PAGE 127
JMA-9100 Instruction Manual 3.2.3 > 3.BASIC OPERATION > 3.2 OBSERVE AND ADJUST VIDEO Tune Normally, use the automatic tune mode. Use the manual tune mode only when best tuning is not possible in the automatic tune mode due to deterioration of magnetron. This radar system provides the automatic tune mode and the manual tune mode.
PAGE 128
JMA-9100 Instruction Manual 3.2.4 > 3.BASIC OPERATION > 3.2 OBSERVE AND ADJUST VIDEO Adjust Gain [GAIN] If the gain is too high, unnecessary signals including receiver noise and false images increase resulting in reduction of visibility of targets. On the contrary, if the gain is too low, targets including ships and dangerous objects may not be clearly indicated. Be sure to always adjust for the best gain. See also the Section 3.2.8 "To get the appropriate image that targets can be easily observed".
PAGE 129
JMA-9100 Instruction Manual 3.2.5 > 3.BASIC OPERATION > 3.2 OBSERVE AND ADJUST VIDEO Suppress Sea Clutter [SEA] When using the [AUTO SEA] function, never set the suppression level too high canceling out all image noises from the sea surface at close range. Detection of not only echoes from waves but also targets such as other ships or dangerous objects will become inhibited. When using the [AUTO SEA] function, make sure to choose the most appropriate image noise suppression level.
PAGE 130
JMA-9100 Instruction Manual > 3.BASIC OPERATION i > 3.2 OBSERVE AND ADJUST VIDEO It is recommended to restore the setting to the factory default, if you lost the appropriate settings.The factory default level is shown on the bar chart as a green line. The factory defafult level is assigned by every function mode. See the Section 3.9 "USE FUNCTION KEY [USER]" 3.2.5.
PAGE 131
JMA-9100 Instruction Manual 3.2.6 > 3.BASIC OPERATION > 3.2 OBSERVE AND ADJUST VIDEO Suppress Rain/Snow Clutter [RAIN] When using the [AUTO RAIN] function, never set the suppression level too high canceling out all image noises from the rain or snow at the close range. Detection of not only echoes from the rain or snow but also targets such as other ships or dangerous objects will become inhibited.
PAGE 132
JMA-9100 Instruction Manual 3.2.6.2 > 3.BASIC OPERATION > 3.2 OBSERVE AND ADJUST VIDEO Using the automatic rain / snow clutter suppression mode The rain / snow clutter suppression in accordance with the intensity of rain / snow clutter is possible. Use this mode when the rain / snow clutter's intensity differs according to directional orientation. Procedures 1) Press the [RAIN] dial. Alternatively, Left-click the Rain MAN button located at the lower left of the display.
PAGE 133
JMA-9100 Instruction Manual 3.2.8 > 3.BASIC OPERATION > 3.2 OBSERVE AND ADJUST VIDEO To get the appropriate image that targets can be easily observed To get the appropriate image that targets can be easily observed which requires an understanding for RADAR signal processing features and an adjustment for the sea state. All of the parameter can be set indivisually and manually, but it may by difficult for even expert person.
PAGE 134
JMA-9100 Instruction Manual 3.3 3.3.1 > 3.BASIC OPERATION > 3.3 OPERATION PROCEDURES OPERATION PROCEDURES Move Cross Cursor Mark by Trackball The cross cursor mark + is used for position designation and other purposes in various operating procedures. The cross cursor mark + moves in coupling with the trackball. If the trackball is rotated up and down or right and left, the cross cursor mark follows the move of the trackball.
PAGE 135
JMA-9100 Instruction Manual 3.3.2 > 3.BASIC OPERATION > 3.3 OPERATION PROCEDURES Operate Software Buttons Software buttons are provided on the radar display so as to easily switch functions without operating menu items. For software buttons that can be operated and their locations, see Section 2.3 "FUNCTIONS OF SOFTWARE BUTTONS". 3 Procedures 1) Put the pointer on the software button on the radar display.
PAGE 136
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.3 OPERATION PROCEDURES 3.3.3 Basic Menu Operation 3.3.3.1 To open the menu By left-clicking the Main button located at the lower right of the radar display, the main menu will open TT AIS By left-clicking the buttons, , , and Main , each function's exclusive menu will open. AZ , adjacent to For the arrangement of software buttons, see Section 2.3 "FUNCTIONS OF SOFTWARE BUTTONS". 3.3.3.
PAGE 137
JMA-9100 Instruction Manual 3.3.3.7 > 3.BASIC OPERATION > 3.3 OPERATION PROCEDURES Menu Operation with the Trackball Item Selected item Press numeric keys corresponding to the desired item number to display the selected item. Present state Press numeric keys corresponding to the desired item number to select a set value. Cursor When the [ > ] mark appears at the right end of a menu item, press numeric keys corresponding to the selected item number to move to a lower level.
PAGE 138
JMA-9100 Instruction Manual 3.3.4.1 > 3.BASIC OPERATION > 3.3 OPERATION PROCEDURES Numeric value input screen Entered value Numeric button - button + button Clear button 3.3.4.2 Enter button Directly entering a numeric value Procedures 1) On the numeric value input screen, sequentially left-click the software number keys located on the radar screen, and enter a desired numeric value. For example, when entering 1 → 2 → 3 → click the software number keys as shown below.
PAGE 139
JMA-9100 Instruction Manual 3.3.4.3 > 3.BASIC OPERATION > 3.3 OPERATION PROCEDURES Increasing or decreasing a numeric value Procedures 1) On the numeric value input screen, sequentially left-click the software button ＋ or － located on the radar screen, and enter a desired numeric value. For example, when adjusting 123.0° to 123.4° for a bearing value, sequentially left-click the software number keys as shown below.
PAGE 140
JMA-9100 Instruction Manual 3.3.4.5 > 3.BASIC OPERATION > 3.3 OPERATION PROCEDURES Entering latitude/longitude Procedures 1) On the latitude/longitude input screen, sequentially click numeric buttons to enter latitude (XX°XX．XXX'). For example, to enter 12°34.567', sequentially click numeric buttons as follows. 1 2) 3) → 2 → 3 → 4 → → 5 6 → 7 To make change between north latitude and south latitude, use ＋ and － . North latitude:Left-click the ＋ button.
PAGE 141
JMA-9100 Instruction Manual 3.3.4.6 > 3.BASIC OPERATION > 3.3 OPERATION PROCEDURES Character input screen Character/Number button Entered character 3 Enter button Delete button Back Space button Exit button 3.3.4.7 Entering a character Procedures 1) On the character input screen, use trackball to select alphabet from A to Z, numbers from 0 to 9, or symbols (only comments for mark/line), and then left-click the ENT button to enter one character of the name to be inputted.
PAGE 142
JMA-9100 Instruction Manual 3.3.5 > 3.BASIC OPERATION > 3.3 OPERATION PROCEDURES Overview of Menu Structure The menu structure of this radar system consists of eight frequently used function menus, one main menu, and one service man menu used for the installation settings. Software buttons for opening those menus are displayed in the menu area located at the bottom ten of the display. For each menu item and structure, see the menu list in the appendix.
PAGE 143
JMA-9100 Instruction Manual 3.4 3.4.1 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION GENERAL RADAR OPERATION Interference Rejection (IR) Interference by other radars is rejected. 3 Attention • When viewing a radar beacon or SART signal, select IR Off (Interference Rejector OFF) because IR processing suppresses the video. Procedures 1) Left-click the IR button located at the lower left of the radar display. The interference rejection modes are switched.
PAGE 144
JMA-9100 Instruction Manual 3.4.2 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Switch Transmitter Pulse Length [GAIN] Procedures 1) Press [GAIN] dial Values of the transmitter pulse width are switched. MP1 MP2 LP1 LP2 Effects of transmitter pulse width With SP selected: The transmitter pulse becomes shorter, and the range resolution improves. The effect of suppressing sea clutter returns and rain/snow clutter returns heightens.
PAGE 145
JMA-9100 Instruction Manual 3.4.3 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Target Enhance (ENH) The dimension of video display is enlarged to enhance a target. Procedures 1) Left-click the ENH button located at the lower left of the radar display. The target enlargement levels are switched. ENH Off ⇒ ENH Level1 ⇒ ENH Level2 ⇒ ENH Level3 ⇒ ENH Off Effect of target enlargement :Expansion off Select this mode resolution is required.
PAGE 146
JMA-9100 Instruction Manual 3.4.4 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Use Video Processing (PROC) This function reduces unnecessary noise to highlight targets. Attention • When viewing a radar beacon, SART signal, or fast moving target on the radar display, select PROC Off (video process off). • If video processing mode is set to CORREL , it may be difficult to detect high speed target. Procedures 1) Left-click the PROC button located at the lower left of the display.
PAGE 147
JMA-9100 Instruction Manual 3.4.5 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Switch Azimuth Display Mode (AZI MODE) Select the bearing for the radar video to be displayed on the radar display. Procedures 1) Left-click the AZI Mode button located at the lower left of the display. 3 The bearing display modes are switched. H Up → N Up → C Up True Bearing Mode [North Up] The video is displayed so that the zenith of the PPI (0° on range rings) points to the due north.
PAGE 148
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION 3.4.6 Switch True/Relative Motion Display Mode (TM/RM) 3.4.6.1 Switching Relative Motion (RM) Mode to True Motion (TM) Mode Procedures 1) Left-click the motion mode button located at the upper left of the radar display. RM(T) → TM The true motion mode will be selected. In the true motion mode, the own ship’s position on the radar display moves depending upon its speed and course and the influence of the current.
PAGE 149
JMA-9100 Instruction Manual 3.4.7 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Move Own Ship’s Display Position (Off Center) The own ship’s position can be moved from the display center to any position within 66% of the display radius. This function is convenient for observing a wide coverage in any direction. If Off Center functions set to scanner position is outside of the PPI range, when function switching display with reference to scanner position.
PAGE 150
JMA-9100 Instruction Manual 3.4.8 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Display Radar Trails (Trails) Other ship's movements and speeds can be monitored from the lengths and directions of their trails, serving for collision avoidance. The trail length varies according to setting. 3.4.8.1 Changing the length of the trail Procedures 1) Left-click the Trails button located at the upper left of the display. RADAR trails display time Values of the length of the radar trails are switched.
PAGE 151
JMA-9100 Instruction Manual 3.4.8.3 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Trails Motion Mode There are two types of trails: relative motion trails and true motion trails. Relative motion The system plots the trails of a target at a position relative to trails: the own ship. The operator can easily judge whether the target is approaching the own ship. While the own ship is moving, the system also plots the trails of land and other fixed targets.
PAGE 152
JMA-9100 Instruction Manual 3.4.8.4 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Changing Motion Mode of Trails (Trails Mode) Procedures 1) Click the Trails Mode located at the upper right of the radar display. RADAR trails true/relative The trails motion modes are switched.
PAGE 153
JMA-9100 Instruction Manual 3.4.9 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Zoom (x2) This function doubles the size of radar video near a specified position. NOTE: If the range is 0.125 NM , this function is not available. Procedures 1) Left-click the x2 button located at the lower left of the display. The zoom mode is selected. 2) Subsequently, put the cross cursor mark on a location you want to zoom into, and press the left key of the trackball. The zoom is set.
PAGE 154
JMA-9100 Instruction Manual 3.4.10 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Hide/Display Range Rings [HL OFF] Procedures 1) Press the [HL OFF] key. Alternatively, Left-click the button located at the lower right of the display. HL Off The ship's heading line (HL) is hidden while the [HL OFF] key is held down. The ship's heading line that indicates the course of own ship is always shown on the radar display.
PAGE 155
JMA-9100 Instruction Manual 3.4.12 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Switch Day/Night Mode [DAY/NIGHT] Several combinations of the display color and brilliance according to the ambient lighting conditions are provided. The display color setting is easily changed. Procedures 1) Press the [DAY/NIGHT] key. Alternatively, left-click the Day/Night button located at the lower right of the radar display. The DAY/NIGHT modes are switched.
PAGE 156
JMA-9100 Instruction Manual 3.4.14 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Set True Bearing When the GYRO I/F is used to enter a gyro signal, there is a rare case in which a true bearing value indicated by the master gyro does not match the true bearing value indicated by this radar system. In that case, adjust the true bearing value of this system so that it matches the value indicated by the master gyro.
PAGE 157
JMA-9100 Instruction Manual NOTE: 3.4.15.2 > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION •If the single axis water log display can present the speed of the ship in other than the forward direction, the direction of movement should be indicated unambiguously. Therefore single axis water logs cannot detect the effect of leeway. •If ships in shallow water, when the accuracy of the dual-axis log may be decreased. If ships in deep sea area, when the accuracy of the dual-axis log error may be occurred.
PAGE 158
JMA-9100 Instruction Manual 2) > 3.BASIC OPERATION > 3.4 GENERAL RADAR OPERATION Set whether to make corrections or not. 1. Heading Correction ⇔ Off 3) On Input the correction value. Press the ＋ for longitude. or － button to select south and north for latitude or the east and west For how to input numeric data on the numeric value input screen, see Section 3.3.4 "Operation on Numeric Value, Latitude / Longitude and Character Input menu". 3.4.16.
PAGE 159
JMA-9100 Instruction Manual 3.5 > 3.BASIC OPERATION > 3.5 USE OWN SHIP'S TRACK USE OWN SHIP'S TRACK The own ship's track function saves and displays own ship's track. If navigation equipment is connected, this radar system records latitude/longitude data sent from the navigation equipment and displays own ship's track. NOTE: Even when own ship's track storage interval is turned , own ship's track can be displayed.
PAGE 160
JMA-9100 Instruction Manual 3.5.2 > 3.BASIC OPERATION > 3.5 USE OWN SHIP'S TRACK Set Display Color of Own Ship's Track (Display Own Track Color) Own ship's track can be saved in seven different colors. Own ship's track can be displayed or not displayed individually by color. Procedures 1) Open the Display Own Track Setting menu by performing the menu operation Track → 1. DISP Own Track Color The Display Own Track Setting menu will open. Operations differ according to the following set modes.
PAGE 161
JMA-9100 Instruction Manual 3.5.3 > 3.BASIC OPERATION > 3.5 USE OWN SHIP'S TRACK Save Own Ship's Track (Own Track Memory) To save own ship's track, storage at a specified time interval and at a specified range interval can be selected. The track storage interval can be selected from 10 preset time intervals and 8 preset range intervals. Storage intervals that can be selected Time : 3 sec, 5 sec, 10 sec, 30 sec, 1 min, 3 min, 5 min, 10 min, 30 min, and 60 min Range : 0.1 NM, 0.2 NM, 0.3 NM, 0.
PAGE 162
JMA-9100 Instruction Manual 3.5.5 > 3.BASIC OPERATION > 3.5 USE OWN SHIP'S TRACK Clear Own Ship's Track (Clear Own Track) This function cancels the storing of own ship's track. Procedures 1) Open the Clear Own Track Color menu by performing the menu operation below. Track → 2. Clear Own Track Color The Clear Own Track Color menu will appear. 2) Left-click the button for the color to be deleted. All : All tracks are deleted / Gray / Blue / Red White Only track of specified color is deleted.
PAGE 163
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.5 USE OWN SHIP'S TRACK Procedures 1) Left-click the display. Track button located at the lower right of the Track menu 3 The Own Track Menu will appear. 2) Left-click the item button of 3. Track Type . The numeric value of the navigation data can be shown by the color of own ship's track. : The expanded own ship's track function is not used.
PAGE 164
JMA-9100 Instruction Manual 3.5.7 > 3.BASIC OPERATION > 3.5 USE OWN SHIP'S TRACK Use Water Depth Track (Water Depth Track) Set the corresponding conditions for the water depth value and the color of own ship's track by performing the operation below. Procedures 1) Open the Water Depth Setting menu by performing the menu operation below. Track → 6. Water Depth Setting The Water Depth Setting menu will appear.
PAGE 165
JMA-9100 Instruction Manual 3.5.8 > 3.BASIC OPERATION > 3.5 USE OWN SHIP'S TRACK Use Water Temperature Track (Water TEMP Track) Set the corresponding conditions for the water temperature value and the color of own ship's track by performing the operation below. Procedures 1) Open the Water TEMP. Setting menu by performing the menu operation below Track → 7. Water TEMP. Setting The Water TEMP. Setting menu will appear.
PAGE 166
JMA-9100 Instruction Manual 3.5.9 > 3.BASIC OPERATION > 3.5 USE OWN SHIP'S TRACK Use Tidal Current Track (Current Vector Track) Set the conditions for adding tidal current vectors to own ship's track by performing the operation below. Procedures 1) Open the Current Setting menu by performing the menu operation below. Track → 8. Current Setting The Current Setting menu will appear. Set the tidal current vector display conditions.
PAGE 167
JMA-9100 Instruction Manual 3.6 > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP DISPLAY USER MAP Up to 20,000 items of NAV lines, coastlines, depth contours, and NAV marks can be created, displayed, loaded, and saved. (This function is available only when navigation equipment is connected to this radar system.) Marks that can be used : 29 types Lines that can be used : 3 types (solid, broken, and dashed-dotted line) Color of mark and lines : 7 colors that can be used i 3.6.
PAGE 168
JMA-9100 Instruction Manual 2) > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP Left-click the mark font mark. □ button to select a font for the The mark fonts are switched. 3) Left-click the C button located to the right of the mark font to select a color for the mark. The color for the mark font located to the right of the Cursor change. 4) button will Left-click at a desired location on the radar display. The specified mark will be displayed in the specified color.
PAGE 169
JMA-9100 Instruction Manual 5) > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP Move the cursor to a desired location on the radar display and left-click. A line is plotted between the previous point and the end point. Repeat this procedure so that sequential lines can be plotted. 6) When you want to finish plotting the line, left-click at the previous point. Line plotting will be terminated. To plot another line, repeat procedures 3. 3.6.1.
PAGE 170
JMA-9100 Instruction Manual 5) > 3.BASIC OPERATION Left-click the longitude. > 3.6 DISPLAY USER MAP button to input the latitude / 3. L/L For the input method on the latitude / longitude input screen, see Section 3.3.4.5 "Entering latitude/longitude" 6) Left-click the 4. Comment button to input the comment. For the input method on the character input screen, see Section 3.3.4.7 "Entering a character" The window will not be open when the system is in the transmission state.
PAGE 171
JMA-9100 Instruction Manual 2) > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP Specify whether to turn on or off the display for each type of mark and line. When 1. All is selected, the setting will reflect to all types of marks and lines. Off : All types are not displayed. Individual : All types are displayed. On : Setting by type is activated. 3.6.2.2 3 Setting display by color Procedures 1) Open the Display Mark Color Type menu by performing the menu operation below. U.Map → 5.
PAGE 172
JMA-9100 Instruction Manual 2) > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP Specify the mark font size. Normal : The mark is displayed in normal size. Small : The mark is displayed in a size smaller than usual. 3.6.2.4 Setting the character size for comments Procedures 1) Open the Comment Font Size menu by performing the menu operation below. U.Map → 5. Mark Display Setting → 4. Comment Font Size The Comment Font Size menu will appear. 2) Specify the comment font size.
PAGE 173
JMA-9100 Instruction Manual > 3.BASIC OPERATION 3.6 DISPLAY USER MAP 2) Use the number buttons (xx°xxx.xxx'). 3) To make changes between north latitude and south latitude, use the ＋ and － buttons. 4) 0 to > 9 to enter a value of latitude North latitude : Left-click the ＋ button. South latitude : Left-click the － button. Left-click the ENT button. The manually entered latitude will be determined. Then, enter the value of longitude. 5) Use the number buttons (xx°xxx.xxx').
PAGE 174
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP The user map move mode is selected. Move Map 3) is displayed in the cursor mode located at the upper right of the display. Put the cursor on a mark or line, and left-click. When a mark or line to be moved is selected, the 4) Move the cursor mark will appear. cursor mark to the destination, and left-click. The selected mark or line is moved to the destination. To move another mark or line, repeat procedures 3 and 4.
PAGE 175
JMA-9100 Instruction Manual 3.6.3.3 > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP Deleting a mark or line (Delete) With regard to the created user map, a mark or line is deleted individually. Procedures 1) Open the Edit User Map menu by performing the following menu operation. U.Map → 2. Edit User Map The Edit User Map menu will appear. 2) Left-click the 4. Delete button. The user map delete mode is selected.
PAGE 176
JMA-9100 Instruction Manual 3.6.3.4 > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP Inserting a vertex into a line (Insert/Move Vertex) With regard to the created user map, a vertex is inserted into a line. Procedures 1) Open the Edit User Map menu by performing the following menu operation. U.Map → 2. Edit User Map The Edit User Map menu will appear. 2) Left-click the 5. Insert/Move Vertex button. The user map insert/correction mode is selected.
PAGE 177
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP (Example) The side line into which a vertex is inserted 3 Inserted vertex 3.6.3.5 Correcting the mark or vertex of a line (Insert/Move Vertex) With regard to the created user map, a mark or line is corrected. Procedures 1) Open the Edit User Map menu by performing the following menu operation. U.Map → 2. Edit User Map The Edit User Map menu will appear. 2) Left-click the 5. Insert/Move Vertex button.
PAGE 178
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP The cursor mode changes to the normal operation mode, terminating the user map insertion/correction mode. (Example) Original vertex New vertex 3.6.3.6 Deleting a mark or vertex from a line (Delete Vertex) With regard to the created user map, a vertex is deleted individually from a mark or line. Procedures 1) Open the Edit User Map menu by performing the following menu operation. U.Map → 2.
PAGE 179
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP The cursor mode changes to the normal operation mode, terminating the user map delete mode. (Example) 3 The vertex to be deleted 3.6.3.7 Batch clearing marks or lines (Clear) With regard to the created user map, marks or lines are batch cleared by type or by color. Procedures 1) Open the Edit User Map menu by performing the following menu operation. U.Map → 2. Edit User Map The Edit User Map menu will appear.
PAGE 180
JMA-9100 Instruction Manual 3) > 3.BASIC OPERATION Left-click the > 3.6 DISPLAY USER MAP 1. Yes button. The selected mark will be deleted. NOTE: If data is not copied on the flash memory card (option), the data is not be reloaded. 3.6.4 Correct Position on User Map (Shift User Map) 3.6.4.1 Correcting the display position on the user map (Shift) If the display position on the user map is different from an actual position, it can be changed to the correct position in manual mode.
PAGE 181
JMA-9100 Instruction Manual 3.6.4.2 > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP Restoring the corrected user map to its original state (Shift Clear) Procedures 1) Open the Mark Operations menu by performing the following menu operation. U.Map 4. Shift Clear → Only the most recently corrected data (for a single input) will be cleared, and the data will be displayed at its original position. At this time, Map Shift is not displayed in the map position correction (lower right of the display).
PAGE 182
JMA-9100 Instruction Manual 5) > 3.BASIC OPERATION Left-click the > 3.6 DISPLAY USER MAP button. 3. Load The list of navigation data saved in the system will be displayed. 6) Left-click the button for the file to be loaded. Confirmation Window will appear. 7) Left-click the 1. Yes button. The selected navigation data will be loaded and displayed on the radar display. 3.6.5.
PAGE 183
JMA-9100 Instruction Manual 2) > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP Open the File Operations menu by performing the following menu operation. U.Map → 3) 7. File Operation Left-click the item button of card slot. and select the 1. Select Card Slot 3 Slot1 and Slot2 of the Select Card Slot items are switched. 4) Left-click the button. 5. Save The Input File Name screen will appear. 5) Enter the file name to be saved. Up to 10 characters can be entered.
PAGE 184
JMA-9100 Instruction Manual 4) > 3.BASIC OPERATION Left-click the > 3.6 DISPLAY USER MAP button. 6. Erase The Erace screen will appear. The list of navigation data saved in the card will be displayed. 5) Click numeric buttons corresponding to the number for the file to be deleted. Confirmation Window will appear. 6) Left-click the 1. Yes button. The selected navigation data is deleted and the name of the file is deleted from the list. 3.6.5.
PAGE 185
JMA-9100 Instruction Manual 3.6.6 > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP Set and Display Geodetic System (Geodetic) To create navigation information, set the geodetic system that is used with the connected navigation equipment. When navigation information is loaded, the geodetic system used when the navigation information was saved, is displayed. Make sure that the displayed geodetic system is identical to the one used with the navigation equipment.
PAGE 186
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.6 DISPLAY USER MAP Table3-1： Geodetic System List # NAME 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 WGS-84 WGS-72 Japan North American 1927(U.
PAGE 187
JMA-9100 Instruction Manual 3.7 > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION USE ROUTE FUNCTION In this radar system, a destination mark set by navigation equipment can be displayed, and a simple route can be created, displayed, loaded and saved. (To use this function, navigation equipment must be connected to this system) i 3.7.1 If radar video is poor visibility caused by route function, click the Map button to turn off the Map function.
PAGE 188
JMA-9100 Instruction Manual 3.7.1.1 > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Displaying route created by the radar system (Internal) In this radar system, route created by the radar system are displayed as shown below. Planned Course 001 Route alarm line 070T 074T Waypoint 003 OPQRS Waypoint bearing vector 2.50kn 000 ABCDE 135T 5.00kn 12.5kn Comments 062T 10.
PAGE 189
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Procedures 1) Open the Set Route Sequence menu by performing the menu operation below. Route → 2. WPT/Route Setting → 2) Left-click the 3. Set Route Sequence 7. New Monitor Route button. Confirmation Window will appear. 3) Left-click the 1. Yes button. The saved route data will be deleted. 3.7.2.2 Adding a Waypoint (Add Waypoint) New Waypoint data is added to the route data saved in the radar system.
PAGE 190
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION 4) To add another Waypoint, repeat procedure 3. 5) To finish adding a Waypoint, left-click twice at the last Waypoint. The Waypoint adding mode is cancelled. (Example) 023 062T 12.0kn Rubber band 024 Last Waypoint 3.7.2.3 Correcting coordinates of a Waypoint (Correct Position) The coordinates of a Waypoint in the route data saved in the radar system are corrected.
PAGE 191
JMA-9100 Instruction Manual 4) > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Move the cursor to new coordinates, and left-click. The coordinates of the Waypoint are corrected, and then the Waypoint correcting mode is cancelled. (Example) 025 064T 025 108T 064T 8.00kn 12.0kn 026 12.0kn 024 024 Waypoint that is to have its position corrected 025 064T 026 Rubber band 3 Cross cursor mark Planned Course 108T 8.00kn 12.0kn 108T 8.00kn 026 026 024 024 060T 106T 12.0kn 8.
PAGE 192
JMA-9100 Instruction Manual 4) > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION On the radar display, put the cursor on the line extending between Waypoints that is to have its Planned Speed corrected. The section that is to have its Planned Speed corrected is specified, and the new Planned Speed is applied to the section. 5) To correct the Planned Speed of another section, repeat procedures 3 and 4. 6) To finish correcting Planned Speed, left-click the 4. Correct Planned Speed button.
PAGE 193
JMA-9100 Instruction Manual 3) > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION On the radar display, put the cursor on a Waypoint to be deleted, and left-click. The specified Waypoint is deleted, and the previous and following Waypoints are then connected by a line. 4) To delete another Waypoint, repeat procedure 3. 5) To finish deleting a Waypoint, left-click the button. 3 5. Delete The Waypoint deleting mode will be cancelled. (Example) Waypoint to be deleted 000 002 113T 8.
PAGE 194
JMA-9100 Instruction Manual 2) > 3.BASIC OPERATION Left-click the > 3.7 USE ROUTE FUNCTION button. 6. Insert The Waypoint inserting mode is selected. 3) On the radar display, put the cursor on the section line into which a Waypoint is to be inserted, and left-click. The section is specified, the cursor becomes a cross cursor mark, and the cross cursor mark is connected to the previous and following Waypoints by a rubber band.
PAGE 195
JMA-9100 Instruction Manual 3.7.3 > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Edit Route Make with Latitude and Longitude (Waypoint Input) In this radar system, it is possible to create and correct route by performing operation on the Waipoint Input menu. Waypoint Number Waypoint Scroll Waypoint Latitude/Longitude Planned Speed Waypoint Comment 3 Waypoint Scroll 3.7.3.
PAGE 196
JMA-9100 Instruction Manual 3.7.3.2 > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Adding a Waypoint (Add) New Waypoint data is added to the route data saved in the radar system. Procedures 1) Open the Waipoint Input menu. 2) Left-click the ADD button. The new latitude of waypoint is reversed. 3) Enter a latitude / longitude and a planned speed. A Waypoint will be added. For the input method on the latitude / longitude and numeric value input screen, see Section 3.3.4.
PAGE 197
JMA-9100 Instruction Manual 3.7.3.4 > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Correcting latitude / longitude of a Waypoint (LAT/LON) The latitude / longitude of a Waypoint in the route data saved in the radar system are corrected. Procedures 1) Open the Waipoint Input menu. 2) Left-click the Waypoint Scroll button. Left-click to show the desired latitude / longitude. 3) Left-click the Latitude / Longitude button to be corrected. The latitude of waypoint is reversed.
PAGE 198
JMA-9100 Instruction Manual 3.7.3.6 > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Deleting a Waypoint (DEL) The specified Waypoint in the route data saved in the radar system is deleted. Procedures 1) Open the Waipoint Input menu. 2) Left-click the Waypoint Scroll button. Left-click to show the desired waypoint. 3) Left-click the DEL button to be corrected. Confirmation Window will appear. 4) Left-click the 1. Yes button.
PAGE 199
JMA-9100 Instruction Manual 3.7.4 > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Use Route Monitoring Function (Waypoint/Route Alarm) This radar system can monitor the movement of own ship with regard to its route and activate a variety of alarms. Destination alarm When own ship arrives at next Waypoint, an alarm will (Waypoint Alarm): be activated. Route alarm: When own ship deviates from the specified route, an alarm will be activated. 3.7.4.
PAGE 200
JMA-9100 Instruction Manual > 3.BASIC OPERATION Arrival > 3.7 USE ROUTE FUNCTION / Break Off 0.00nm 3.7.4.2 : Set the operation mode. : Set the radius of the Waypoint alarm circle. If 0.00nm is set, alarm operation will be turned off. Route Alarm The route alarm is activated when own ship deviates from the specified width of the route. The route alarm lines are displayed with a specified width provided. Route alarm line Break Off alarm is activated when own ship is outside the specified range.
PAGE 201
JMA-9100 Instruction Manual 3.7.5 > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Method of Using Route The method of using the route will be described. Displaying the route The internal route is displayed according to the procedures in (Route Alarm Color): Section 3.7.1 "Display Route/Destination Mark (Select Route)". Selecting the forward or Whether to use Waypoints forward or backward is selected.
PAGE 202
JMA-9100 Instruction Manual 3.7.5.2 > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Skipping/Back-skipping of the route (Waypoint Skip/ Waypoint Back Skip) Next Waypoint of the route can be changed by user manually. 007 006 : Forward ：Backward 000 ki p ac k S oint B Wayp W ay poin t Ski p 005 003 001 002 k ip nt S y poi Wa Wayp o in 004 t Ba c k S kip Skipping of route The Waypoint which is after the next Waypoint is set as the (Waypoint Skip): next Waypoint.
PAGE 203
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Display character size :Specify the size of the numeric value and character displayed on (SEL NUM/Comment Size) the radar display. Waypoint bearing vector :Set the method to display line between next Waypoint and own (Waypoint Vector) ship. Display of bearing distance to the :Select the start point to be used for the bearing/distance display in destination(Status of Origin/DEST) the Waypoint data display area.
PAGE 204
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Procedures Open the Next menu by performing the menu operation below. 1) Route → 2. WPT/Route Setting → Left-click the set value of the select an operation mode. 2) Normal Small 3.7.6.3 9. Next 1. SEL NUM/Comment Size item, and :Numbers and characters are displayed in normal size. :Numbers and characters are displayed in a size smaller than usual.
PAGE 205
JMA-9100 Instruction Manual 3.7.6.4 > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Displaying bearing distance to the Waypoint (Status of Origin/DEST) Select a start point used to display bearing/distance in the Waypoint data display area. Procedures 1) Open the Next menu by performing the menu operation below. Route → → 2) 9. Next Left-click the set value of the select an operation mode. From CURR POSN Fix 3.7.6.5 3 2. WPT/Route Setting 3.
PAGE 206
JMA-9100 Instruction Manual 3.7.6.6 > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Updating Waypoint data (Waypoint Switch Mode) Set how to update the Waypoint number when one Waypoint has been reached. Procedures 1) Open the WPT/Route Operations menu by performing the menu operation below. Route → 2) 3.7.7 3. WPT/Route Operations Left-click the set value of the select an operation mode. 2.
PAGE 207
JMA-9100 Instruction Manual 3.7.8 > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Operate Route Data File Route data saved in the radar system can be saved onto a flash memory card, and data can be loaded from a flash memory card into the radar system. With regard to this item, only route data can be saved and loaded. To save or load own ship's track, target track data, and mark/line data, see Section 3.11 "USING CARD".
PAGE 208
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Procedures 1) Insert a flash memory card into the card slot. 2) Open the File Operations menu by performing the menu operation below. Route → 3) Left-click the 4. File Operation button. 3. Save The file name input screen will appear. For the input method on the character input screen, see Section 3.3.4.7 "Entering a character". 4) After having entered a file name, left-click the ENT button.
PAGE 209
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.7 USE ROUTE FUNCTION Procedures 1) Insert a flash memory card into the card slot. 2) Open the File Operations menu by performing the menu operation below. Route → 3) Left-click the 4. File Operation 2. Load button. Contents of the specified memory card (file list) will be displayed. 4) Left-click the button for the desired file name. Confirmation Window will appear. 5) Left-click the 1. Yes button.
PAGE 210
JMA-9100 Instruction Manual 3) > 3.BASIC OPERATION Left-click the > 3.7 USE ROUTE FUNCTION 4. Erase button. Contents of the specified memory card (file list) will be displayed. 4) Left-click the button for the desired file name. Confirmation Window will appear. 5) Left-click the 1. Yes button. A route data file with the specified file name will be erased.
PAGE 211
JMA-9100 Instruction Manual 3.8 3.8.1 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS APPLIED OPERATIONS Set Radar Signal Processing (Process Setting) This function enables the setting of detail information about radar signal processing. 3 Procedures 1) Open the Process Setting menu by performing the menu operation below. Main → 3. RADAR Menu → 1. Process Setting The Process Setting menu will appear.
PAGE 212
JMA-9100 Instruction Manual 3.8.1.2 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Video Noise Rejection • This function rejects signals that assumed as noise and clutter in radar videos. Off • Select to display radar videos like analog signals. • Select Level1 or Level2 to suppress noise and clutter. • Select Level1 or Level2 to superimpose-display the chart. Off ： Turns off the noise rejection function, and displays all signals. Targets are popped up from noise and displayed like analog signals.
PAGE 213
JMA-9100 Instruction Manual 3.8.1.4 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Process Switch • This function sets a specific area and switches the video process mode between the inside and outside of the area. • In Section 3.8.1.5 "2nd Porcess Mode" 2nd Process Mode, set the second video process mode for the area outside the boundary. • In [2] PROCESS of Main Menu , set the first video process mode for the area inside the boundary.
PAGE 214
JMA-9100 Instruction Manual 3.8.1.7 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Fast Target Detection • This function displays fast moving targets that are suppressed in scancorrelative process mode. • This function is enabled when 5Scan CORREL 3Scan CORREL , 4Scan CORREL is selected as the video process mode. , or • If unwanted waves remain on the radar display, suppress them by using the [SEA], [RAIN], or [GAIN] dial, or adjusting the interference rejection mode.
PAGE 215
JMA-9100 Instruction Manual 3.8.2 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Set Radar Trails (RADAR Trails Setting) This function enables the setting of detail information about radar trails processing. Procedures 1) Open the RADAR Trails Setting menu by performing the menu operation below. Main → 3. RADAR Menu → 2. RADAR Trails Setting The RADAR Trails Setting menu will appear. Detail data about radar trails processing can be set by changing the settings of each menu item.
PAGE 216
JMA-9100 Instruction Manual 3.8.2.3 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Trails Reduction • Make a setting for thinning radar trails. • The effect of thinning increases in order of Level1 → Level2 → Level3 . • Radar videos do not become obscure because of the thinning of radar trails. Off 3.8.2.4 3.8.2.5 : Disables the Trails Reduction function. Level1 : Enables the Trails Reduction function. (Effect: Low) Level2 : Enables the Trails Reduction function.
PAGE 217
JMA-9100 Instruction Manual 3.8.3 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Set Scanner Unit (TXRX Setting) This function enables the setting of detail information about an antenna. Procedures 1) Open the TXRX Setting menu by performing the menu operation below. Main → 3. RADAR Menu → 3. TXRX Setting The TXRX Setting menu will appear. Detail information about antenna operation can be set by changing the settings of the menu items. 3.8.3.
PAGE 218
JMA-9100 Instruction Manual 3.8.3.4 3.8.4 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Ice Class Standby Mode • In this mode, the antenna is rotated when transmission is in the standby state. • This mode is effective to prevent the antenna's rotating shaft from freezing. Off :The ice class standby mode is not used. When transmission is in the standby state, the antenna also stops rotating. On :The ice class standby mode is used. When transmission is in the standby state, the antenna rotates.
PAGE 219
JMA-9100 Instruction Manual 3.8.4.2 3.8.4.3 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Cursor Length • Set the length of the cross cursor mark on the radar display. Short Cuts the cross cursor mark in length. Long : Makes the cross cursor mark twice as long as when Short is selected. Cursor Pattern • The type of the cross cursor mark displayed of the display is selected. : Type 1 is selected for the cross cursor mark 1 displayed in the radar display.
PAGE 220
JMA-9100 Instruction Manual 3.8.5.2 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Day/Night • Specify the mode to be changed. • The following modes are available: Day1 : Day mode 1 : Used under bright lighting conditions. Day2 : Day mode 2 : Used under bright lighting conditions. Day3 : Day mode 3 : Used under bright lighting conditions. Dusk : Dusk mode : Used under dim lighting conditions. Night : Night mode : Used under dark lighting conditions.
PAGE 221
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Procedures Open the Brilliance Setting menu by performing the menu operation below. 1) Main → 7. Sub Menu → 2. Brilliance Setting Display Brilliance Setting menu will appear. Setting brilliance of each element • Specify the brilliance for the element. • Level4 indicates maximum brilliance and Level1 indicates minimum brilliance. • The brilliance for the following elements can be specified.
PAGE 222
JMA-9100 Instruction Manual 3.8.5.5 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Setting target symbol brilliance (TT) The brilliance of the target symbol on the radar display is adjusted. Procedures 1) TT ○ Left-click the button located at the lower right of the radar display, and adjust the brilliance of the target symbol so as to get the best view of the video display. The brilliance of the target symbol can be adjusted on four stages without opening the Brilliance Setting menu.
PAGE 223
JMA-9100 Instruction Manual 3.8.7 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Set User Option Keys [OPTION 1/2] Users can freely make settings with [OPTION 1] key and [OPTION 2] key. By using the keys, users can open a frequently used menu by only single operation, or assign special functions, to the user key switches. 3.8.7.1 Initial Setting (Option Key Setting) Set functions that can be performed with the option key switches.
PAGE 224
JMA-9100 Instruction Manual 3.8.7.2 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Using Option Keys (Directly displaying a specified Preset the Menu Menu ) that is to be displayed with the option key switch. Procedures 1) Perform the general menu open procedure to open the menu that is to be directly displayed with Option Key. 2) While the menu is open, hold down [OPTION 1] key or [OPTION 2] key for 2 seconds. The menu currently being displayed is saved for the pressed option key. i 3.8.7.
PAGE 225
JMA-9100 Instruction Manual 3.8.8 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Set Navigation Data Display (Multi Window Setting) By performing the following operation, it is possible to display navigation data of the wind direction / velocity, water depth and the like, as a graph on the radar display. Procedures 1) Open the Multi Window Setting menu by performing the menu operation below. Main → 4. Multi Window Setting The Multi Window Setting menu will appear.
PAGE 226
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS • Navigation information of the water depth, water temperature, tidal current, wind direction/velocity, and destination is displayed with numeric values. • Left-click the Target button located at thelower righit of the display. The navigation data display function is switched between On and Off. Off 3.8.8.3 : Does not display the numeric values of navigation information.
PAGE 227
JMA-9100 Instruction Manual > 3.BASIC OPERATION 10min : Sets 10 minutes as the time range. 15min : Sets 15 minutes as the time range. 30min : Sets 30 minutes as the time range. 60min : Sets 60 minutes as the time range. 12hour : Sets 12 hours as the time range. > 3.8 APPLIED OPERATIONS [4] Depth Unit • Set the unit of water depth for the water-depth graph. Feet 3.8.8.4 : The foot is used as the unit of water depth. Fathom : The fathom is used as the unit of water depth.
PAGE 228
JMA-9100 Instruction Manual 3.8.8.5 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS TEMP Graph Setting • The TEMP Graph Setting menu will appear. [1] TEMP Graph Display • Determine whether to display the graph of the water-temperature data that has been received on the radar display. • One of two digital information areas is used to display data. • When the water-temperature graph is displayed, the sizes of the target tracking (TT)/AIS numeric data display areas are exclusively decreased.
PAGE 229
JMA-9100 Instruction Manual 3.8.8.6 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS Course Bar Setting • The Course Bar Setting menu will appear. [1] Course Bar Display • Determine whether to display the bar graph for the course data that has been received on the radar display. • One of two digital information areas is used to display data. • When the course-bar graph is displayed, the sizes of the target tracking (TT)/ AIS numeric data display areas are exclusively decreased.
PAGE 230
JMA-9100 Instruction Manual 3.8.9 > 3.BASIC OPERATION > 3.8 APPLIED OPERATIONS AUTO Backup Data can be automatically backed up when the power supply is turned on. Procedures 1) Insert a flash memory card into the card slot. Flash memory card (option) is necessary. 2) Open the Plot Setting menu by performing the following menu operation. Main → 3) 8. Plot Setting Left-click the item button of 5. AUTO Backup Backup button. The AUTO Backup menu will appear.
PAGE 231
JMA-9100 Instruction Manual 3.9 > 3.BASIC OPERATION > 3.9 USE FUNCTION KEY [USER] USE FUNCTION KEY [USER] "Radar Function Setting" is provided for easily obtaining the best radar video by storing complex radar signal processing settings in the optimum status by use, and calling the setting in accordance with the conditions for using the function. Functions are factory-set for general use, and the settings can be fine adjusted by operating the menu.
PAGE 232
JMA-9100 Instruction Manual 3.9.1.3 > 3.BASIC OPERATION > 3.9 USE FUNCTION KEY [USER] Changing Function Setting (memory contents change) To change the memory contents of functions 1 to 4, use the function setting menu. For how to operate the function setting menu, see Section 3.9.3 "Overview of Function Operations (User Function Setting)". 3.9.2 Function Setting Menu Items The function setting menu has the items below. page 1 1. Mode 2. IR 3. Process 4. Target Enhance 5. AUTO Sea/Rain 6.
PAGE 233
JMA-9100 Instruction Manual 3.9.3 > 3.BASIC OPERATION > 3.9 USE FUNCTION KEY [USER] Overview of Function Operations (User Function Setting) The following outlines the operation of each function selected from the function setting menu: Procedures 1) Open the Process Setting menu by performing the menu operation below. Main → 3. RADAR Menu → 1. Process Setting → 8. User Function Setting The User Function Setting menu will appear.
PAGE 234
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.9 USE FUNCTION KEY [USER] page 1-[2] IR (Radar interference rejection) • Same function as IR Setting described in Section 3.4.1 "Interference Rejection (IR)". page 1-[3] Process (Video process) • Same function as PROCESS Setting described in Section 3.4.4 "Use Video Processing (PROC)" page 1-[4] Target Enhance • Same function as TARGET ENHANCE Setting described in Section 3.4.3 "Target Enhance (ENH)".
PAGE 235
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.9 USE FUNCTION KEY [USER] page 2-[1]~[7] PL (Pulse Length) • Sets the standard transmitter pulse length in each range. • When the range is called, the pulse range is used. page 3-[1]~[7] Video setting menu (Process Setting) • Operation is the same as that of the Process Setting menu described in Section 3.8.1 "Set Radar Signal Processing (Process Setting)".
PAGE 236
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.9 USE FUNCTION KEY [USER] page 5-[3] Small Buoy Detection • Reduces the loss of signal processing during detection of small targets. Off :Activates the general signal processing mode. On :Activates the small buoy detection mode that reduces the loss of signal processing. page 5-[4] FishNet Detection • Use this mode to detect small targets hidden by sea clutter returns.
PAGE 237
JMA-9100 Instruction Manual 3.9.4 > 3.BASIC OPERATION > 3.9 USE FUNCTION KEY [USER] Overview of saved Function Setting Data The overview of saved function setting data is as follows: Factory-set data: : Saved data that general operation cannot change Default data: : Standard data of each function mode that users can change Data that can be : Saved data that can be called by pressing the [USER] key called: Procedures 1) Open the User Function Setting menu by performing the menu operation below.
PAGE 238
JMA-9100 Instruction Manual 3.10 > 3.BASIC OPERATION > 3.10 USE USER SETTING USE USER SETTING The operation status of the radar is recorded. If the system is operated by more than one operator, the operators can register operation status as suitable for them and call the status. Operation status for up to five operations can be registered, and a name can be assigned to each status.
PAGE 239
JMA-9100 Instruction Manual 3.10.2 > 3.BASIC OPERATION > 3.10 USE USER SETTING Load Operating State (Load User Setting) The operating state saved in the system can be loaded by performing the operation below. When the operating state is loaded, the previous operating state data is discarded. Therefore, if you do not want to discard the operating state data, save the operating state by performing the operation described in Section 3.10.1 "Save Operating State (Save User Setting)".
PAGE 240
JMA-9100 Instruction Manual 3.11 > 3.BASIC OPERATION > 3.11 USING CARD USING CARD This radar has two card slots. Inserting a flash memory card (option) into a card slot, you can save the following contents, saved in the processor, in the card or can load data from the card to the processor.
PAGE 241
JMA-9100 Instruction Manual > 3.BASIC OPERATION > 3.11 USING CARD The File Manager window will appear.
PAGE 242
JMA-9100 Instruction Manual 3.11.1.1 > 3.BASIC OPERATION > 3.11 USING CARD Copy Internal Information to Card (Copy Internal -> Card) Procedures 1) While the File Manager window is open, left-click the device 1 selection button. Selected items for Device1 will be displayed. 2) Left-click the 1. Internal button among the selection items. Internal is selected. 3) Left-click the device 2 selection button. Selected items for Device2 will be displayed.
PAGE 243
JMA-9100 Instruction Manual 3.11.1.2 > 3.BASIC OPERATION > 3.11 USING CARD Load Information from Card to Internal Portion (Copy Card -> Internal) Procedures 1) While the File Manager window is open, left-click the device 1 selection button. Selected items for Device1 will be displayed. 2) Left-click the 1. Internal button among the selection items. Internal is selected. 3) Left-click the device 2 selection button. Selected items for Device2 will be displayed.
PAGE 244
JMA-9100 Instruction Manual 3.11.1.3 > 3.BASIC OPERATION > 3.11 USING CARD Copy Information (Copy) Procedures 1) While the File Manager window is open, left-click the device 1 selection button. Selected items for Device1 will be displayed. 2) Left-click the button corresponding to the device from which data is to be copied. The list of files saved in the selected device will be displayed. 3) Left-click the device 2 selection button. Selected items for Device2 will be displayed.
PAGE 245
JMA-9100 Instruction Manual 3.11.1.4 > 3.BASIC OPERATION > 3.11 USING CARD Erase File (Erase) Procedures 1) While the File Manager window is open, left-click the device 1 selection button. Selected items for Device1 will be displayed. 2) Left-click button corresponding to the device in which data to be erased is saved. The list of files saved in the selected device will be displayed. 3) Select data to be erased. Left-click button one more time will cancel the selection.
PAGE 246
JMA-9100 Instruction Manual 3.11.1.6 > 3.BASIC OPERATION > 3.11 USING CARD Showing data saved on the card (Show Card) Procedures 1) While the File Manager window is open, left-click the device 1 selection button. Selected items for Device1 or Device2 will be displayed. 2) Left-click button corresponding to the device in which data to be displayed is saved. The list of files saved in the selected device will be displayed. Exit 1) Left-click the button. 1.
PAGE 247
SECTION 4 MEASUREMENT OF RANGE AND BEARING MEASUREMENT OF RANGE AND BEARING 4.1 USE OF NAVIGATION TOOLS ..............................................................4-1 4.1.1 Using Cursor (Cursor) ....................................................................4-2 4.1.2 Using Range Rings (Range Rings) ................................................4-2 4.1.3 Using Electronic Bearing Line (EBL1/EBL2) ................................4-3 4.1.4 Using Parallel Index Lines (PI Menu) ........................
PAGE 248
PAGE 249
JMA-9100 Instruction Manual 4.1 > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS USE OF NAVIGATION TOOLS The system is equipped with the navigation tools below. Cursor: Specifies an arbitrary point, and measures the range and bearing from the own ship. Range Rings: Displays concentric circles with own ship's position as the center at specified intervals, and the rings are used as rough guides for range measurement.
PAGE 250
JMA-9100 Instruction Manual 4.1.1 > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS Using Cursor (Cursor) Procedures 1) Move the cursor onto the PPI display by moving the trackball. When the cursor is moved onto the PPI display, the arrow cursor turns into a cross cursor. 4.1.2 Using Range Rings (Range Rings) Procedures 1) Left-click the Rings Range rings display On / Off button on upper left area on the display.
PAGE 251
JMA-9100 Instruction Manual 4.1.3 > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS Using Electronic Bearing Line (EBL1/EBL2) Electronic bearing lines (EBL) are indispensable to the measurement of bearings. Operators must be familiar with the operation of EBL beforehand. The system is equipped with two EBL. The bearing and starting point of an EBL can be operated separately from the other EBL.
PAGE 252
JMA-9100 Instruction Manual 4.1.3.1 > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS Operating EBL (EBL) Procedures 1) Press the [EBL1] or [EBL2] key. The EBL button (located at the upper right of the display) will be highlighted, and the selected EBL becomes operable. Turn the [EBL] dial. To turn the [EBL] dial to the right, turn the EBL control clockwise; to turn the [EBL] dial to the left, turn the EBL control counterclockwise. Cancel 1) Press the [EBL1] or [EBL2] key again.
PAGE 253
JMA-9100 Instruction Manual > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS [2] To return the EBL starting point to own ship's position Procedures 1) Make EBL1 or EBL2 operable. 2) Press the [EBL] dial to set _ for the EBL1 / EBL2 starting point mode switching located at the upper right of the display. The selected EBL starting point will be set as the own ship's position. 4.1.3.
PAGE 254
JMA-9100 Instruction Manual > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS Procedures 1) Open the EBL/Cursor Setting menu by performing the following menu operation. Main → 7. Sub Menu → 2) 9. EBL/Cursor Setting Left-click at the item button 1. EBL1 Bearing FIX of or 2. EBL2 Bearing FIX Angle :EBL bearing is fixed to the preset value. Screen :EBL bearing is fixed on the radar display. i . Course data is necessary for turning on this function.
PAGE 255
JMA-9100 Instruction Manual > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS EBL2 VRM2 EBL1 VRM1 4 VRM Operation The range value of the current VRM1 or VRM2 on the PPI display is shown in the VRM1/2 range located at the upper right of the display. The currently operable VRM1 or VRM2 VRM2 is highlighted in the VRM1 button located at the upper right of the display. 4.1.3.4 To operate VRM (VRM) Procedures 1) Press the [VRM1] or [VRM2] key.
PAGE 256
JMA-9100 Instruction Manual 4.1.4 > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS Using Parallel Index Lines (PI Menu) Parallel index lines can be displayed. 4.1.4.1 Operating Parallel Index Lines (PI) Procedures 1) Press the [VRM] dial. Parallel index lines and the PI Menu will appear. To change the bearing of parallel index lines, turn the [EBL] dial, to change the line interval, turn the [VRM] dial.
PAGE 257
JMA-9100 Instruction Manual > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS HL ① ③ ② ④ EBL1 EBL2 ① VRM 1 ② 4 VRM 2 ③ ④ During the operation of parallel index lines, pressing the [EBL1] or [EBL2] key disables operation for rotation directions. Pressing the [VRM1] or [VRM2] key disables operation for parallel index line intervals. 4.1.4.3 Settings in PI Menu (PI Menu) The operation of parallel index lines can be set in the PI Menu.
PAGE 258
JMA-9100 Instruction Manual > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS [2] Operation Mode Sets an operation mode for parallel index lines. PI PI Individual All PI PI Track Equiangular All :All the parallel lines are operated at the same time. Individual :The bearing of each line is operated individually. Track :Equally spaced lateral lines are displayed on both sides. Equiangular a.
PAGE 259
JMA-9100 Instruction Manual > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS [3] Control Determines whether to operate all the lines at the same time. The setting items are determined by the setting of Section [2] "Operation Mode". a. If is selected All The setting cannot be changed. All b. If :All the lines are operated at the same time. is selected Individual Determine whether to set consecutive lines or individual lines. Sequential Index Line1 to c.
PAGE 260
JMA-9100 Instruction Manual > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS [6] Next Moves to the next page. [7] Range Scale Link Determines the operation of parallel index line intervals when the range is changed. On :The intervals are fixed with the actual range (nm). The appearance of parallel index line intervals changes when the range is changed. Off :The intervals are fixed with the display range. The parallel index line intervals (nm) change when the range is changed.
PAGE 261
JMA-9100 Instruction Manual c. If Track > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS is selected True HL Index Line1 to Line8 : Displayed with true bearing (with North as reference). : Displayed with the heading line as reference. : Displayed with a specified line as reference. Line1, Line3, Line5 and Line7 correspond to Group1, Group2, Group3 and Group4, respectively. d.
PAGE 262
JMA-9100 Instruction Manual > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS 4.1.5 Operating EBL Maneuver Function (EBL Maneuver Setting) 4.1.5.1 Initial Setting (EBL Maneuver Setting) Procedures 1) Open the EBL Maneuver Setting menu by performing the following menu operation. Main → 2) 1. EBL Maneuver Setting Set the following parameters. Reach Turn Mode :Set the range from when the rudder is steered to when the ship beings to turn. :Select a turn mode.
PAGE 263
JMA-9100 Instruction Manual 4.1.5.2 > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS Creation of Maneuver Curve (EBL Maneuver) Procedures 1) Left-click the item button of 1. EBL Maneuver Maneuver Setting menu is open. while the EBL The EBL maneuver function will be set to on or off. A auxiliary line for maneuver curve creation, a maneuver curve, and a WOL will appear on the radar display.
PAGE 264
JMA-9100 Instruction Manual 4.1.6 > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS Operating EBL, VRM, and PI with Cursor When the cursor mode is set to AUTO (located at the upper right of the display), EBL, VRM, and PI can be operated simply by using the trackball. 4.1.6.1 Operating Electronic Bearing Line (EBL) Procedures 1) Put the cursor on EBL1 or EBL2, and left-click. When the cursor is moved to it, EBL1 or EBL2 is shown at the upper right of the cursor.
PAGE 265
JMA-9100 Instruction Manual 4.1.6.3 > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS Operating EBL and VRM Concurrently (EBL・VRM) Procedures 1) Put the cursor on the intersection marker ( ○ or ● ), and leftclick. EBL1 VRM1 EBL2 VRM2 When the cursor is moved to it, or is shown at the upper right of the cursor. The EBL and VRM become operable when leftclicking. 2) Move the cursor to the bearing / range to be set. The EBL and VRM will move as the cursor moves. 3) Left-click.
PAGE 266
JMA-9100 Instruction Manual > 4.MEASUREMENT OF RANGE AND BEARING > 4.1 USE OF NAVIGATION TOOLS [2] To change parallel index line intervals Procedures 1) Put the cursor on near the end of line, and left-click. PI When the cursor is moved there, it will turn into and will be displayed at the upper right of the cursor. The parallel index lines become operable when left-clicking. 2) Move the cursor to the interval to be set. The parallel index lines interval will change as the cursor moves.
PAGE 267
JMA-9100 Instruction Manual 4.2 > 4.MEASUREMENT OF RANGE AND BEARING > 4.2 MEASUREMENT OF RANGE AND BEARING MEASUREMENT OF RANGE AND BEARING 4.2.1 Measurement with Cursor Position (Cursor) Procedures 1) 2) Make sure of the target echoes on the radar display. Move the cursor to the target. The bearing and range of the target will be shown in the Cursor bearing / range located at the upper right of the display. The range is a distance from the own ship's position. 0 45.0° Cursor Target 6.
PAGE 268
JMA-9100 Instruction Manual 4.2.2 > 4.MEASUREMENT OF RANGE AND BEARING > 4.2 MEASUREMENT OF RANGE AND BEARING Measurement with Electronic Bearing Line and Variable Range Marker [EBL] [VRM] Procedures 1) Press the [EBL1] key. EBL1 numeric value indication true / relative switching EBL1 adjustment EBL1 The (located at the upper right of the display) will be highlighted, and EBL1 will be shown with a dotted line on the PPI display. 2) Move the EBL1 to the target by turning the [EBL] dial.
PAGE 269
JMA-9100 Instruction Manual 4.2.3 > 4.MEASUREMENT OF RANGE AND BEARING > 4.2 MEASUREMENT OF RANGE AND BEARING Measurement with Two Arbitrary Points Procedures 1) Press the [EBL2] key. EBL2 The ( located at the upper right of the display) will be highlighted, and EBL2 will be shown on the PPI display. 2) Press the [EBL] dial to select C for the EBL2 starting point mode switching located at the upper right of the display.
PAGE 270
JMA-9100 Instruction Manual > 4.MEASUREMENT OF RANGE AND BEARING 4－ 22 > 4.
PAGE 271
SECTION 5 OPERATION OF TARGET TRACKING AND AIS OPERATION OF TARGET TRACKING AND AIS 5.1 PREPARATION ......................................................................................5-1 5.1.1 Collision Avoidance ........................................................................5-2 5.1.2 Definitions of Symbols ...................................................................5-5 5.1.3 Radar Display ..................................................................................5-8 5.1.
PAGE 272
5.3.1 Restrictions ....................................................................................5-26 5.3.2 Setting AIS Display Function (AIS Function) ..............................5-26 5.3.3 Activate AIS Targets (Activate AIS) .............................................5-27 5.3.4 Deactivate AIS Targets (Deactivate AIS) .....................................5-27 5.3.5 Displaying AIS Information [TGT DATA] .....................................5-28 5.3.6 Displaying Target ID No.
PAGE 273
JMA-9100 Instruction Manual 5.1 > 5.OPERATION OF TARGET TRACKING AND AIS > 5.1 PREPARATION PREPARATION Attention • There are the following limitations on use of the target acquisition and target tracking functions. [I] Resolution between adjacent targets and swapping during automatic target tracking Depending on the particular distance and echo size, resolution between adjacent targets during automatic target tracking usually ranges somewhere between 0.03 to 0.05 NM.
PAGE 274
JMA-9100 Instruction Manual > 5.OPERATION OF TARGET TRACKING AND AIS > 5.1 PREPARATION If the mode is ground stabilization, SOG/COG used for own ship's information in target tracking. If the mode is sea stabilization, SPD (speed through the water) / HDG (heading) used for own ship's information in target tracking. AIS (Automatic Identification System) function The AIS function shows the target’s information on the radar display, using other ship's information sent out from the AIS unit. 5.1.
PAGE 275
JMA-9100 Instruction Manual 5.1.1.2 > 5.OPERATION OF TARGET TRACKING AND AIS > 5.1 PREPARATION Marine Accidents and Collisions Among marine accidents, collision accidents have been highlighted as the tonnages and speeds of ships become higher along with the increase in traffic at sea.
PAGE 276
JMA-9100 Instruction Manual 5.1.1.4 > 5.OPERATION OF TARGET TRACKING AND AIS > 5.1 PREPARATION Relative Vector and True Vector From two points of view, collision prediction and avoidance, it is necessary to obtain the relative vector of other ship for prediction and the true vector of other ship for collision avoidance in order to grasp other ship’s aspect. The relationship between the relative vector and true vector is shown in Fig. 5-3.
PAGE 277
JMA-9100 Instruction Manual > 5.OPERATION OF TARGET TRACKING AND AIS 5.1.2 Definitions of Symbols 5.1.2.1 Types and Definitions of Target Tracking Symbols Vector/ Symbol Definition > 5.1 PREPARATION Remarks Initial acquisition This symbol is displayed until the vector is target displayed after target acquisition. 12 Target acquired in The alarm sounds. automatic The alarm message (New Target) turns red and acquisition zone blinks.The symbol is red colored.
PAGE 278
JMA-9100 Instruction Manual 5.1.2.2 > 5.OPERATION OF TARGET TRACKING AND AIS > 5.1 PREPARATION Types and Definitions of AIS Target Symbols Vector/ Symbol Definition Remarks Sleeping target This symbol is displayed when received data is valid.The direction of the triangle's vertex indicates the target's bow or course. Activated target The heading direction is displayed with a solid line, and the course vector is displayed with a dotted line.
PAGE 279
JMA-9100 Instruction Manual > 5.OPERATION OF TARGET TRACKING AND AIS > 5.1 PREPARATION 2. Activated AIS target 3. Sleeping AIS target The vector of an AIS target is to be displayed with a vector over ground or over water, depending on the speed sensor setting and current offset setting. The type of the currently displayed vector can be confirmed by viewing the setting of the stable mode.
PAGE 280
JMA-9100 Instruction Manual > 5.OPERATION OF TARGET TRACKING AND AIS > 5.1 PREPARATION b. Setting of AIS Target Symbol Display This function switches the AIS target symbol display between on and off. Procedures 1) Left-click the button in the Target Information located at the upper right of the display. The AIS target symbol display will be set to on or off. 5.1.3 Radar Display 5.1.3.