Full Product Manual

ManualsBrandsJames Hardie ManualsBuilding materialsMagnolia Home Hardie Shingle HZ5 15.25 in. x 48 in. Fiber Cement Straight Edge Mudflats

General

Product

Information

Working

Safely

Tools for

Cutting and

Fastening

General

Installation

Requirements

General

Fastener

Requirements

Finishing and

Maintenance

HardieTrim

Boards/Battens

HardieWrap

Weather Barrier

HardieSofﬁt

Panels

HardiePlank

Lap Siding

HardieShingle

Siding

HardiePanel

Vertical Siding

ESR-1844 &

2290 Report

Appendix/

Glossary

HardieShingle

Siding Product Description

HardieShingle

siding is ﬁber-cement shingle siding for sidewall applications. HardieShingle siding is available

as straight-edge panels or staggered-edge panels 48 in. long by 16 in high. HardieShingle panels also come as

decorative half-round shingles. For smaller coverage areas, individual shingles are also available in 4.2 in, 5.5 in,

6.75 in, 7.25 in & 10 in widths. Please see your James Hardie dealer for local availability of these products.

HardieShingle siding is available as a preﬁnished James Hardie product with ColorPlus

Technology. The ColorPlus

coating is a factory applied, oven-baked ﬁnish available on a variety of James Hardie siding and trim products. See

your local dealer for details and availability of products, colors and accessories.

Half-Round Staggered Edge Panel

Straight Edge Panel Individual Shingles

Summary of content (13 pages)

PAGE 1
General Product Information Working Safely Tools for Cutting and Fastening General Installation Requirements HardieShingle® siding is fiber-cement shingle siding for sidewall applications. HardieShingle siding is available as straight-edge panels or staggered-edge panels 48 in. long by 16 in high. HardieShingle panels also come as decorative half-round shingles. For smaller coverage areas, individual shingles are also available in 4.2 in, 5.5 in, 6.75 in, 7.25 in & 10 in widths.
PAGE 2
General Product Information Installation of HardieShingle Siding ® Working Safely INDIVIDUAL SHINGLES Water resistive barrier 11.
PAGE 3
General Product Information Working Safely Tools for Cutting and Fastening General Installation Requirements General Fastener Requirements Finishing and Maintenance HardieTrim® HardieWrap® Boards/Battens Weather Barrier HardieSoffit® Panels HardiePlank® Lap Siding ® HARDIESHINGLE® PANELS For HardieShingle® panels start at one end and work across the wall. 1. Measure and trim the first panel to make sure the end of the panel falls over framing. 2. Using the chalk line as a guide along the panel top edge.
PAGE 4
General Product Information Working Safely ! WARNING Tools for Cutting and Fastening James Hardie recommends installing HardieShingle panel over rated wood sheathing. INSTALLING HARDIESHINGLE® PANEL DIRECT TO 7/16 IN SHEATHING General Installation Requirements Refer to ESR-2290 for allowable wind loads. Panel and Individuals may be mixed together to reduce waste and save time. Straight Wall Center of Wall Left Right 2. Make all shingle length cuts at trim, not mid wall 11.4 3.
PAGE 5
General Product Information Working Safely Tools for Cutting and Fastening General Installation Requirements General Fastener Requirements Finishing and Maintenance HardieTrim® HardieWrap® Boards/Battens Weather Barrier HardieSoffit® Panels ® HALF-ROUND DECORATIVE SHINGLE PANELS (CONTINUED) For best appearance, half-round shingle panel installations on gable ends should end with a single round shingle at the gable peak. To make this happen, calculation of the actual number of courses is necessary.
PAGE 6
HardieShingle Siding ® SINGLE FAMILY INSTALLATION REQUIREMENTS EFFECTIVE DECEMBER 2019 IMPORTANT: FAILURE TO FOLLOW JAMES HARDIE WRITTEN INSTALLATION INSTRUCTIONS AND COMPLY WITH APPLICABLE BUILDING CODES MAY VIOLATE LOCAL LAWS, AFFECT BUILDING ENVELOPE PERFORMANCE AND MAY AFFECT WARRANTY COVERAGE. FAILURE TO COMPLY WITH ALL HEALTH AND SAFETY REGULATIONS WHEN CUTTING AND INSTALLING THIS PRODUCT MAY RESULT IN PERSONAL INJURY.
PAGE 7
HardieShingle® Siding CLEARANCE AND FLASHING REQUIREMENTS Figure 1 Figure 2 Roof to Wall Figure 3 Horizontal Flashing Figure 4 Kickout Flashing Slabs, Paths, Steps to Siding As required by IRC code min 4 in. x 4 in. Min. 2 in Min. ¼ in Figure 7 Figure 9 Figure 8 Deck to Wall Min. 2 in Ground to Siding Figure 10 Gutter to Siding Sheltered Areas Figure 11 Mortar/Masonry L-Flashing Z-Flashing Z-Flashing Min. 2 in. Min. ¼ in Min. 6 in Min. ½ in Min. 1 in Figure 12 Drip Edge Min. ¼ in.
PAGE 8
HardieShingle® Siding GABLE INSTALLATION: Installation over sheathing is recommended (Required for Individuals) for gables.
PAGE 9
HardieShingle® Siding HARDIESHINGLE STAGGERED EDGE PANELS INSTALLATION Figure 22 Fastener Requirements 0.083 in x 0.187 in HD x 1 1/2 in long ringshank nails are used for fastening HardieShingle® Staggered Edge Panels to both framing and to 7/16 in thick APA rated sheathing. Trim 1/8 in min. gap for caulk Steps 1- 4 16 in or 24 in o.c.
PAGE 10
HardieShingle® Siding HARDIESHINGLE INDIVIDUAL SHINGLE INSTALLATION HardieShingle Individual Shingles must be installed with the widest part of the shingle placed downwards and directly to minimum 7/16 in thick sheathing. Fastener Requirements 0.091 in x 0.221 in HD x 1 1/2 in or 0.121 in x 0.371 in HD x 1 1/4 in long corrosion resistant siding nails are used for fixing HardieShingle siding to 7/16 in thick APA rated sheathing.
PAGE 11
HardieShingle® Siding Figure 28 CORNER DETAILS A. Panels butted against corner boards. B. Panels butted against square wood strip on inside corner, flashing behind. C. Laced outside corner. D. Laced inside corner. minimum (1 in) thick trim WINDOWS AND DOORS Building wall components such as windows, doors and other exterior wall penetrations shall be installed in accordance with the component manufacturer’s written installation instructions and local building codes.
PAGE 12
HardieShingle® Siding PAINTING CUT EDGE TREATMENT Caulk, paint or prime all field cut edges. James Hardie touch-up kits are required to touch-up ColorPlus products. CAULKING For best results use an Elastomeric Joint Sealant complying with ASTM C920 Grade NS, Class 25 or higher or a Latex Joint Sealant complying with ASTM C834. Caulking/Sealant must be applied in accordance with the caulking/sealant manufacturer’s written instructions. Note: some caulking manufacturers do not allow "tooling".
PAGE 13
HardieShingle® Siding HARDIESHINGLE® INDIVIDUAL SHINGLE INSTALLATION Figure 30 Trim HardieShingle Individual Shingles must be installed with the widest part of the shingle placed downwards and directly to minimum 7/16 in thick sheathing. 1/8 in min. gap for caulk 16 in or 24 in o.c. water-resistive barrier sheathing Fastener Requirements 0.091 in x 0.221 in HD x 1 1/2 in or 0.121 in x 0.