User's Manual

There is a built-in PTC to help protect the
motor and battery from over-heating
Skateboard may need to be immobile for a time allowing
it to cool down while the PTC recovers.
IMPORTANT SAFETY INFORMATION
NEVER use near glass and other fragile objects.
NEVER drive near traffic, building, trees, people, animals, or other obstructions.
NEVER operate during storms or other adverse weather conditions.
1 2
5 6
3 4
7 8
TM & © 2017 MANUFACTURED BY JAKKS PACIFIC, INC., 2951 28TH STREET, SANTA MONICA, CA 90405 U.S.A.
Contents may vary in style, color, shape and decoration from images shown on package or in advertising.
Questions or comments? www.jakks.com, [e-mail], 1-877-875-2557 in North America,
or 01344 638909 in the United Kingdom.
ATTENTION! Remove and discard packaging ties and fasteners before giving toy to child.
Retain packaging since it contains important information.
MADE IN CHINA
Warning. Not suitable for children under 36 months. Small parts. Choking hazard.
www.jakks.com
BATTERY INSTALLATIONASSEMBLY
ADULT INSTALLATION REQUIRED
If performance diminishes after purchase, replace with fresh batteries.
Requires 2 x “AA” (R6/LR6) batteries (included) and 1 x 8.4V NIMH 700 mAH Battery
NiMH Pack (included).
ADULT INSTALLATION REQUIRED.
BATTERY CHARGING CONTROLLER FUNCTIONS TROUBLESHOOTING
R/C PAIRING
BATTERY SAFETY INFORMATION
WARNING! Battery acid leakage can cause personal injury and cause damage to the product and surrounding
property. If battery leakage occurs, thoroughly wash any affected skin, making sure to keep battery acid away from eyes, ears,
nose and mouth. Immediately wash any clothing or other surface that comes in contact with leaked battery acid. Leaking
batteries may make "popping" sounds. Dispose according to Local, State or Federal Battery Laws.
NEVER mix old and new batteries or different brands of batteries.
NEVER mix alkaline, standard (carbon-zinc), rechargeable (nickel-cadmium) batteries with this product.
58181
XPV® SKATEBOARD
XPV® CONTROLLER
SELF-RIGHTING
ROLL BAR
8.4 V NIMH 700 MAH BATTERY PACK
MICRO USB
CHARGING CABLE
MICRO USB CHARGING CABLE
“AA” (R6/LR6) BATTERIES X2
INSTRUCTION GUIDE
XPV® XTREME PERFORMANCE SKATEBOARD
8+
CONTENTS
CONTROLLER
SKATEBOARD
JAKKS Pacific® Battery or Electrically-Operated Toy 90 DAY LIMITED WARRANTY
Thanks for purchasing a great JAKKS Pacific® product! Please immediately register your product online at www.jakks.com/warranty. Registration is not required for the effectiveness of this limited warranty.
IMPORTANT NOTICE TO CONSUMER:
This 90 DAY LIMITED WARRANTY applies to the original product purchaser, provided the product: 1) was purchased from an authorized JAKKS™ distributor/dealer/retailer, and 2) is returned at your expense,
postage pre-paid and insured, along with the original dated sales receipt to the address noted below. Please save a copy of your original sales receipt, as the original receipt will not be returned to you.
If you return the product to us without the original dated sales receipt, this warranty coverage will not apply. If the product is determined by JAKKS to be defective and returned to JAKKS within the 90 day
warranty period, we will (at our option) repair or replace it. Return shipment to you may take up to 6 weeks, depending upon your location. If your product is repaired or replaced, it will be warranted for the longer
of the original warranty or for 30 days after warranty service.
SCOPE OF LIMITED WARRANTY: The product is warranted to be: a) tested and inspected before shipment, and b) free of defects in material and workmanship for 90 days from date of purchase. If a
covered defect occurs within the warranty period, then at our sole option, we will repair or replace the product or provide you with another product of equal value.
WHAT IS NOT COVERED BY LIMITED WARRANTY: THIS WARRANTY IS VOID IF THE PRODUCT HAS BEEN MODIFIED OR REPAIRED BY USER OR OTHERS OR IF IT HAS BEEN DAMAGED
AS A RESULT OF ACCIDENT, IMMERSION IN WATER, NEGLECT, ABUSE, MISUSE, BATTERY LEAKAGE, IMPROPER BATTERY INSTALLATION, UNAUTHORIZED SERVICE, LOSS OF PARTS, WEATHER, ACTS
OF GOD, ANY ACTION OR OMISSION WHICH CONSTITUTES A DEVIATION FROM THE OPERATING INSTRUCTIONS, OR ANY OTHER CAUSES NOT ARISING OUT OF DEFECTS IN WORKMANSHIP OR
MATERIALS.
EXCLUSIONS FROM LIMITED WARRANTY: THIS WARRANTY IS EXCLUSIVE OF AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES RELATED TO THIS PRODUCT, INCLUDING
ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. SPECIAL, INCIDENTAL AND CONSEQUENTIAL DAMAGES ARISING FROM
POSSESSION, USE, OR MALFUNCTION OF THIS PRODUCT ARE EXCLUDED BOTH FOR PROPERTY DAMAGE AND PERSONAL INJURY TO THE EXTENT LEGALLY PERMITTED.
ADDITIONAL LEGAL RIGHTS: This warranty provides specific legal rights. You may have other or different rights in your state or country.
QUESTIONS OR COMMENTS: If you experience product difficulties or have questions or comments, you may contact our Consumer Relations department as follows:
Phone: [phone] (toll-free, North America only) or 909-594-7771 (Monday-Friday, 7:30AM-4:30PM Pacific/GMT -8).
Mail: JAKKS Consumer Relations, 21749 Baker Parkway, Walnut, California USA 91789.
Email: [e-mail]
WHEN WRITING TO US: Please include: 1) product name; 2) item number; 3) purchase date; 4) description of the problem being experienced; and 5) your name, address and phone number.
Additionally, if eligible under the warranty and so advised by JAKKS Consumer Relations, also include the defective product and the ORIGINAL dated sales receipt evidencing product purchase. Please retain a
copy of your receipt.
080309
1
2
1
2
3
3
4
2
3
Gently twist the SELF-RIGHTING ROLL BAR as shown.
Lower the SELF-RIGHTING ROLL BAR into the SLOT.
THIS VEHICLE IS DESIGNED FOR OUTDOOR USE AND ITS PERFORMANCE IS
BEST OPTIMIZED ON HARD SURFACES SUCH AS CONCRETE AND ASPHALT.
PERFORMANCE MAY VARY ON GRASS, LOOSE DIRT, WET SURFACES OR CARPET.
Snap RIGHT POST into the round opening located on the SKATEBOARD chassis.
Snap LEFT POST into the round opening located on the SKATEBOARD chassis.
SLOT
CHARGING PORT COVER
BATTERY DOOR LOCATION
CONTROLLER
BOTTOM VIEW
LED
PAIRING
SUCCESSFUL
LEFT
POST
RIGHT
POST
NEVER dispose of batteries in fire, as they may leak and explode.
ALWAYS remove exhausted batteries from toy.
ALWAYS have an adult install batteries consistent with installation instructions.
ONLY use batteries specified by manufacturer.
Batteries are to be inserted with the correct polarity.
The supply terminals are not to be short-circuited.
Non-rechargeable batteries are not to be recharged.
Rechargeable batteries are only to be charged under adult supervision.
1. Locate battery compartment on bottom of CONTROLLER HANDLE.
2. Using a Phillips Head Screwdriver (not included), remove the screw and
battery door.
3. Install 2 new “AA” (R6/LR6) batteries.
4. Replace the battery cover and the screw.
1. Locate battery compartment on bottom of SKATEBOARD.
2. Using a Phillips Head Screwdriver (not included), remove the screws and battery door.
3. Install the 1 x 8.4V 700 mAH Battery NiMH Pack (included).
4. Connect the BATTERY CABLES.
5. Replace the battery cover and the screws.
1
1
2
2
1
3
2
Open the CHARGING PORT COVER on the
SKATEBOARD and move the
ON/OFF/CHARGING switch to charging.
Plug the small end of the MICRO USB CHARGING CABLE into the SKATEBOARD. Plug
the large end of the MICRO USB CHARGING CABLE into a 5V USB power source.
Approximate charging time is 2 – 4.5 hours. LED light remain on when under charged.
When fully charged, LED turns off. Remove the MICRO USB CHARGING CABLE and
close the CHARGING PORT
COVER.
Move the ON/OFF/CHARGING SWITCH on the
SKATEBOARD to the ON position
Move the ON/OFF SWITCH on the CONTROLLER
to the ON position.
Slowly rotate STEERING WHEEL RIGHT or LEFT to make a loose turn. Quickly rotate STEERING WHEEL RIGHT or LEFT to
make a tight turn.
Pull TRIGGER back to move the SKATEBOARD FORWARD. Push TRIGGER forward to move the SKATEBOARD in
REVERSE. Maximum distance from CONTROLLER to SKATEBOARD should not exceed 50 feet.
TRIM CONTROL
Move the TRIM CONTROL LEVER to the RIGHT one
position. Test and repeat if necessary.
REPLACING THE WHEELS
1
Remove the AXLE NUT
using a 5.4 mm NUT DRIVER (not included).
Remove the WHEEL.
Remove the LONG WHEEL ADAPTOR.
Insert a SHORT WHEEL ADAPTOR (included) onto AXLE HUB.
3
2
4
5
6
Install a new open market, 30mm
1/18 SCALE WHEEL* (Not Included).
Install AXLE NUT and tighten with NUT DRIVER.
Move the TRIM CONTROL LEVER to the LEFT one
position. Test and repeat if necessary.
Hold CONTROLLER next to SKATEBOARD (12 inches or closer). LED on CONTROLLER will change from BLINKING to
SOLID when paired. If the units fail to pair, turn them both OFF, and repeat Steps 1 – 3 again.
ROUND
OPENING
LED
LED
LEFT DRIFT RIGHT DRIFT
*Wheel: Outside diameter: 1.45” (37mm); Width: 1.18” (30mm); Tires:
Outside diameter: 2.39” (59mm); Width: 1.18” (30mm)
*Wheel: Outside diameter: 1.45” (37mm); Width: 1.18” (30mm); Tires: Outside diameter: 2.39” (59mm); Width: 1.18” (30mm)
[DESIGNED TO FIT 1/18 SCALE
WHEELS* (Not Included)]
RC / 2.4GHz
See Instructions [page 5] for correct pairing.
Move switch to ON position.
Ensure the batteries in the controller are fresh and the
Skateboard Battery is fully charged.
Make sure the Controller is placed within the signal
receiving range.
SOLUTION
See Instructions [page 2] on how to install the included Roll Bar.
The Roll Bar is able to help the skateboard self-right when on
a hard surface and when it has enough momentum to get
back on its wheels. There can be instances and conditions
where the skateboard will land in a way that does not self
right. Use the skateboard on a hard/even surfaces for best
results.
See instructions [page 5] on how to adjust the Trim Control.
Check the tread on the tires. Make sure the left side and right
side have equal wear. Replace tires [See page 7] if necessary.
ADULT INSTALLATION REQUIRED
ADULT SUPERVISION REQUIRED
ALWAYS PLAY IN SAFE SURROUNDINGS,
AWAY FROM STREETS OR MOVING VEHICLES
Repeat step 1-6 for the REAR WHEEL
PROBLEM
Skateboard won't move.
Skateboard will not
self-right.
Skateboard will not
go in a straight line.
POSSIBLE CAUSE
Skateboard is not paired with Controller.
Skateboard/Controller is switched off.
Weak Battery in Controller/Skateboard.
Controller is not close enough to vehicle.
Roll bar not present or installed correctly.
Skateboard on a soft or uneven surface or does
not have enough momentum to self-right.
Trim Control may need adjusting.
Tires may be worn on one side.
The skateboard was ON
and no longer responds
to the controller
Skateboard may have entered sleep
mode.
If the remote control cannot wake up the skateboard,
power OFF skateboard and then switch to ON and
perform the pairing again
The skateboard suddenly
stops.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil
doit accepter dout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
58181 XPV Skateboard
SizE; 594mm x 210mm x 2
Color: Grayscale
CHOKING HAZARD - Small parts.
Not for children under 3 years.
WARNING:
REAR SHORT WHEEL
ADAPTORS X2
FRONT SHORT WHEEL
ADAPTORS X2