Product Manual

Assembly Instructions/ Instrucciones de ensamblado/
Instructions d’assemblage:
Operating Instructions/ Instrucciones operativas/
Mode d’emploi:
JackJaw
®
206/226 Instruction Sheet
Instructivo de JackJaw
®
Fiche D’Instructions JackJaw
®
Place contents of box on fl oor or table.
Place handle over riser tube with decal
facing up and insert short 3/8” - 24 bolt.
Coloque el contenido de la caja en el
suelo o sobre una mesa. Coloque el
mango sobre el tubo ascendente con
la calcomania hacia arriba e inserte el
tornillo corto de 3/8” pulg-24.
Placer le contenu de l’emballage sur le
sol ou une table. Poser le manche sur
le tube-verin avec l’autocollant vers le
haut et introduire un boulon court de
3/8” - 24.
Start 3/8”-24 self locking nut on to bolt.
Monte la tuerca autoinmobilizadora de
3/8”-24 sobre el tornillo.
Amorcer l’ecrou-frein de 3/8”-24 sur le
boulon.
Swing link arms up to handle. Insert the
long 3/8”-24 bolt through link arms and
handle.
Mueva los enganches hasta el mango.
Inserte el tornillo largo de 3/8”-24 a
traves de los enganches y del mango.
Relever les bras de liaison jusqu’au
manche. Introduire le long boulon de
3/8”-24 a travers les bras de liaison et le
manche.
Use two 9/16” wrenches to tighten riser
bolts and nuts and link arms onto handle.
Note: Nut will stop before contacting
the handle.
Utilice dos llaves de tuercas de 9/16”
para apretar los tornillos del tubo
ascendente y las tuercas y los enganches
al mango.
Nota: la tuerca se detendra antes de
tocar el mango.
A l’aide des cles de 9/16”, serrer les
boulons et ecrous du verin et les bras de
liaison sur le manche.
Remarque: L’ecrou se bloque avant de
venir au contact du manche.
Construction Accessories, Inc. • Phone [phone] • Fax [phone] • www.jackjaw.com
email: [e-mail]
Printed in U.S.A. • Impreso en E.U.A. • Imprime aux Etats-Unis.
Removing the Drive Rod
1. Lift handle to up position so that jaws are fully open.
2. Place unit so that jaws are on either side of the drive rod. Figure 1 below.
3. Push down on handle, clamping on cable and lifting it out of the ground.
Figure 2 below.
4. Repeat motion as necessary until drive rod is free.
Setting the Anchor Cable
1. Lift handle to up position so that jaws are fully open.
2. Place unit so that jaws are on either side of the anchor cable.
3. Push down on handle, clamping on cable and lifting it out of the ground.
Figure 3 below.
4. Repeat motion as necessary until cable is set. You will feel the resistance,
then stop.
Tip: In soft conditions or mud, place a short piece (1 to 2 feet in length) of 2
x 4 lumber under the base of the unit. This will spread the force over a larger
area, allowing stake removal even in muddy conditions.
Caution: Never put your fi ngers or hands between the jaws, or between the
jaws and the stake.
Cuidado: Nunca coloque los dedos o las manos entre las quijadas, o entre las
quijadas y la estaca.
Attention: Ne Jamais placer les doigts ou les mains entre les machoires ni
entre les machoires et le piquet.
Replacement jaws - JJ0206 Part # CA0009 JJ0226 Part #CA0015
Quijadas de repuesto- JJ0206 Pieza # CA0009 JJ0226 Pieza num. CA0015
Machoires de rechange- JJ0206 Ref. CA0009 JJ0226 Ref. CA0015
1.
2.
May 2017
3.