User's Manual

ManualsBrandsJ-Three International Holding ManualsElectronicsBluetooth Adaptor

BluetoothTM USB Adapter

Connect your peripherals and computing devices

without cables

BU-2080J

BU-2081J

BU-2090J

BU-2091J

Quick Installation Guide

Introduction

PC System Requirements

• PC-compatible computer, CPU speed of 200MHz or above

• Memory: 64MB or above, 128MB recommended

• One available USB port, USB 1.1 standard

• Windows® 98 SE, Me, 2000, and XP

Product Contents

• Bluetooth USB Adapter

• CD-ROM for installation software and documentation

• Quick Installation Guide

Step 1: Software Setup

Software Setup for Windows 98 SE, Me, 2000, and XP

To install the software for the USB Adapter, follow the instructions below:

Note: The installation process for Windows XP may look slightly different from Windows

98 SE, Me, and 2000.

Note: Do not insert the USB Adapter into the USB port prior to software

installation.

1. Insert the software installation CD-ROM

into the PC’s CD-ROM drive.

2. The “Software InstallShield Wizard”

window appears. Click on “Next” to

begin the installation process.

/ BU-2063-J

Summary of content (10 pages)

PAGE 1
BluetoothTM USB Adapter Connect your peripherals and computing devices without cables BU-2080J / BU-2063-J BU-2081J BU-2090J BU-2091J Quick Installation Guide Introduction PC System Requirements • PC-compatible computer, CPU speed of 200MHz or above • Memory: 64MB or above, 128MB recommended • One available USB port, USB 1.
PAGE 2
Step 1: Software Setup 3. Choose “I accept the terms in the license agreement” to accept the license agreement. Click on “Next” to continue.
PAGE 3
4. Specify the location where the software files will be installed on your hard drive. It is recommended that you install the software in the default directory “C:\Program Files\WIDCOMM\ Bluetooth Software\”. Click on “Next” to continue.
PAGE 4
3 5. Confirm that the device software is ready to be installed and click on “Install”.
PAGE 5
6. The InstallShield Wizard will begin to install the Bluetooth Software. This may take several minutes. 4 Step 1: Software Setup 7. During the installation process you may be prompted to insert your USB Adapter. If your USB Adapter is not plugged into your computer at this time, you may insert it into an available USB 1.1-compliant port on your desktop or notebook computer, then click “OK” to continue. Click on “Cancel” to continue installation without the Bluetooth device inserted.
PAGE 6
Note: If at any time during the installation process you receive a “Driver Signature Notice”, click “OK” to continue the installation process. 5 Step 1: Software Setup 8. Confirm the completion of the software installation; click “Finish” and restart the system if prompted to do so. 6 Step 1: Software Setup Hardware Setup for Windows 98 SE, Me, 2000, and XP Follow these instructions to install your USB Adapter on your PC.
PAGE 7
available USB A-type connector on your desktop or notebook computer. Your system should register a new USB device found. 2. Choose “Install from a list or specific location”; then click “Next”. Step 2: Hardware Setup 7 3. Browse for the location of the device driver “:\Program Files \WIDCOMM\ Bluetooth\Software\bin\” then click “Next”.
PAGE 8
4. If you receive the following “Hardware installation notice”, click on “Continue Anyway” to continue with the installation process.
PAGE 9
Step 2: Hardware Setup 5. A window will appear that confirms the completion of the hardware installation; click on “Finish” to complete the installation process. Step 2: Hardware Setup 9 Uninstalling the Software for Windows 98 SE, Me, 2000, and XP Follow these instructions to uninstall your USB Adapter on your PC. 1. Insert the CD-ROM included with your USB Adapter. 2. This “InstallShield Wizard” should automatically load. If it does not load, explore the CD and run the “Setup.exe” file. 3.
PAGE 10
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.