J COMMUNICATIONS CO., LTD. FCC ID : OAJFR1500XTM JOB # : 298AK1 EXHIBIT # : 6 FR1500XTM Operating Manual J Communications Co., Ltd. KEY Definition (1) POWER KEY 1) Short key - Press the Power button shortly to turn the unit on. 2) Long key (In case of pressing and holding more than 1.2sec) - After saving all information to EEPRO, the unit is turned off.
(3) (4) (5) (6) (7) (8) 1) Short key – increasing a Mode up. 2) Long key - turning to the TWO-WAY mode, first mode. MENU KEY 1) Short key – increasing a Menu up. 2) Long key - making the Key locked and disabled. Shift/Key lock 1) Short key – shifting Cursor. 2) Long key - releasing Key lock function. UP 1) Short key – increasing Volume or current item. 2) Long key - increasing Volume or current item at a more rapid rate. DOWN 1) Short key – decreasing Volume or current item.
: VIBRATOR CALL icon –appears VIB in the call mode is selected. : BUSY icon – appears carrier detect in the two way channel : KEY LOCK icon –appears when key lock mode is activated. : CHANNEL icon –appears when Two way channel is displayed : CTCSS Code icon –appears when code of Two way channel is displated. :BATTERY strengtt icon strength. ! –indicates the battery charge POWER ON AND OFF OPERATION 0.
Menu key TWO WAY mode. TWO WAY standby display 1) Pressing the mode key in the set up mode allows you to enter the two-way mode. Current channel and code are shown on LCD 2) Detailed function in the two-way mode. (1) Channel/Code selection menu - Pressing the menu key in the standby display of Two way mode allows you to enter the channel selection menu with beeping and the current channel is blinking. You can select the channel by using up and down key.
1) 2) Pressing the mode key in the two-way mode allows you to enter FM radio mode and enter FM standby mode showing current FM operating status after 1 second. Detailed function by menu. (1) FM Seek - Pressing the menu key in the FM Standby display allows you to enter FM seek menu and you can scan the FM radio frequency by using up/down key. If an active broadcast signal is detected, it receives a signal in that channel.
1) Pressing the mode key in the WEATHER MODE allows you to enter COMPASS radio mode and it shows you the current direction on the basis of which radio antenna is heading for. 2) There are 8 directions such as N/NE/E/SE/S/SW/W/NW in the compass direction. 3) Detailed function by menu. (1)Calibration menu - Pressing the menu key in the Compass Standby allows you to enter Compass Calibration menu. If you select CALIB ON by using up or down key, the Calibration is started.
time. 2) Detailed function by menu. (1) Unit selection menu - Pressing the menu key in the Time Standby allows you to enter Unit selection menu and you can select the time unit in the 12/24 hour by using up/down key. (2) Alarm selection menu - Pressing the menu key in the Unit Selection menu allows you to enter the Alarm selection menu and you can select the ALARM Off/ALARM ON by using up/down key. - If the Alarm is on, the radio makes a alarm beeping at the set time.
(4) (5) (6) (7) (8) menu allows you to enter in the Call selection menu. You can select call option out of Off/1/2/3/4/5/6/7 by using up/down key. VIBCALL selection menu - Pressing the menu key in the Call selection menu allows you to enter in the VIBCALL selection menu. You can select VIBCALL option out of Ring/Ring+VIB/VIB by using up/down key. Roger beep selection menu - Pressing the menu key in the VIBCALL selection menu allows you to enter in the Roger beep selection menu.
signal of weather channel. (4) Weather receiving 1) If the weather channel is on, it receives channel. the weather 3. Normal Scan 1) If the Normal Scan is on, it starts scanning all channels. 2) If a transmission is detected, it receives a signal for 5 seconds and then change to next channel. 3) Scan wait time is 5 seconds after receiving. 4) You can pause on any channel for 15 seconds while in the channel Scan mode by pressing the PTT key during of a signal for 5 seconds afterward.
the rule of 300ms/400ms(off/on) for 20 seconds after power save is started and abides by the rule of 300ms/900ms(off/on)after 20 seconds. 7. Low cell indication 1) The radio checks the battery charge strength regularly. 2) The cell icon will blink when the radio is in low battery power after making a low cell beeping. 3) You can not transmit for more than 10 seconds during low cell. 8. RSSI display 1) RSSI Icon and strength appear on the LCD when the radio receives a busy signal. 9.