SAFETY DATA SHEET ClearTop Pour-on Epoxy Part B Section 1. Identification GHS product identifier : ClearTop Pour-on Epoxy Part B Product code : 41032, 41128, 41256 Other means of identification : Not available. Product type : Liquid. Relevant identified uses of the substance or mixture and uses advised against Identified uses Hardener for epoxy resin systems. Uses advised against Not applicable. Supplier's details : J-B Weld Company 400 CMH Road Sulphur Springs, TX 75482 USA info@jbweld.
ClearTop Pour-on Epoxy Part B Section 3. Composition/information on ingredients Substance/mixture : Mixture Other means of identification : Not available. There are no ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section. Section 4.
ClearTop Pour-on Epoxy Part B Section 5. Fire-fighting measures Special protective actions for fire-fighters : Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Move containers from fire area if this can be done without risk. Use water spray to keep fire-exposed containers cool.
ClearTop Pour-on Epoxy Part B Section 7. Handling and storage Conditions for safe storage, including any incompatibilities : Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Eliminate all ignition sources. Separate from oxidizing materials. Keep container tightly closed and sealed until ready for use.
ClearTop Pour-on Epoxy Part B Section 9. Physical and chemical properties and safety characteristics The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated. Appearance Physical state : Liquid. [Viscous liquid.] Color : Clear. Odor Odor threshold pH Melting point/freezing point : Alcohol-like. : Not available. : Not available. : Not available. Boiling point, initial boiling point, and boiling range : Not available.
ClearTop Pour-on Epoxy Part B Section 11. Toxicological information Information on toxicological effects Acute toxicity Not available. Irritation/Corrosion Not available. Sensitization Not available. Mutagenicity Not available. Carcinogenicity Not available. Reproductive toxicity Not available. Teratogenicity Not available. Specific target organ toxicity (single exposure) Not available. Specific target organ toxicity (repeated exposure) Not available. Aspiration hazard Not available.
ClearTop Pour-on Epoxy Part B Section 11. Toxicological information Not available. General : No known significant effects or critical hazards. Carcinogenicity : No known significant effects or critical hazards. Mutagenicity : No known significant effects or critical hazards. Reproductive toxicity : No known significant effects or critical hazards. Numerical measures of toxicity Acute toxicity estimates N/A Section 12. Ecological information Toxicity Not available.
ClearTop Pour-on Epoxy Part B Section 14. Transport information DOT Classification TDG Classification Mexico Classification IMDG IATA UN number Not regulated. UN3082 Not regulated. Not regulated. Not regulated. UN proper shipping name - ENVIRONMENTALLY - - - HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (Oxirane, 2,2'-[ (1-methylethylidene) bis (4,1-phenyleneoxymethylene)] bis-, homopolymer, mixture) Transport hazard class(es) 9 - - - Packing group - III - - - Environmental hazards No.
ClearTop Pour-on Epoxy Part B Section 15. Regulatory information SARA 304 RQ : Not applicable. SARA 311/312 Classification : FLAMMABLE LIQUIDS - Category 4 Composition/information on ingredients No products were found.
ClearTop Pour-on Epoxy Part B Section 15. Regulatory information Thailand Turkey United States Viet Nam : : : : All components are listed or exempted. Not determined. All components are listed or exempted. All components are listed or exempted. Section 16. Other information Hazardous Material Information System (U.S.A.
ClearTop Pour-on Epoxy Part B Section 16. Other information To the best of our knowledge, the information contained herein is accurate. However, neither the above-named supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution.
Ultra Resin Part A J-B Weld Company, LLC Version No: 2.1 Safety Data Sheet according to OSHA HazCom Standard (2012) requirements Issue Date: 11/17/2020 Print Date: 11/17/2020 S.GHS.USA.
Version No: 2.1 Page 2 of 7 Ultra Resin Part A Issue Date: 11/17/2020 Print Date: 11/17/2020 Precautionary statement(s) Prevention P271 Use only outdoors or in a well-ventilated area. P280 Wear protective gloves/protective clothing/eye protection/face protection. P261 Avoid breathing mist/vapours/spray. P272 Contaminated work clothing should not be allowed out of the workplace. Precautionary statement(s) Response P321 Specific treatment (see advice on this label).
Version No: 2.1 Page 3 of 7 Issue Date: 11/17/2020 Print Date: 11/17/2020 Ultra Resin Part A SECTION 5 Fire-fighting measures Extinguishing media There is no restriction on the type of extinguisher which may be used. Use extinguishing media suitable for surrounding area. Special hazards arising from the substrate or mixture Fire Incompatibility None known. Special protective equipment and precautions for fire-fighters Alert Fire Department and tell them location and nature of hazard.
Version No: 2.1 Page 4 of 7 Issue Date: 11/17/2020 Print Date: 11/17/2020 Ultra Resin Part A Ingredient Occupational Exposure Band Rating Occupational Exposure Band Limit bisphenol A diglycidyl ether polymer E ≤ 0.1 ppm 1,4-butanediol diglycidyl ether E ≤ 0.1 ppm Notes: Occupational exposure banding is a process of assigning chemicals into specific categories or bands based on a chemical's potency and the adverse health outcomes associated with exposure.
Version No: 2.1 Page 5 of 7 Issue Date: 11/17/2020 Print Date: 11/17/2020 Ultra Resin Part A Hazardous decomposition products See section 5 SECTION 11 Toxicological information Information on toxicological effects Inhaled Ingestion Skin Contact Eye Chronic The material can cause respiratory irritation in some persons. The body's response to such irritation can cause further lung damage. Accidental ingestion of the material may be damaging to the health of the individual.
Version No: 2.1 Page 6 of 7 Issue Date: 11/17/2020 Print Date: 11/17/2020 Ultra Resin Part A bisphenol A diglycidyl ether polymer 1,4-butanediol diglycidyl ether Legend: Endpoint Test Duration (hr) Species Value Source EC50 48 Crustacea ca.2mg/L 2 Endpoint Test Duration (hr) Species Value Source LC50 96 Fish 24mg/L 2 EC50 72 Algae or other aquatic plants 110mg/L 2 EC0 24 Crustacea 32mg/L 2 NOEL 72 Algae or other aquatic plants 40mg/L 2 Extracted from 1.
Version No: 2.