EmulationEngine 11a/b/g User's Guide CHAPTER 6: The Command Line Interface (CLI) The CLI can be used to display and modify the configuration of the EmulationEngine from a PC that is connected via Telnet or the serial port. The CLI also includes commands to configure and run virtual stations, display statistics, and to access the System Under Test. The EmulationEngine maintains statistics and event log files that you can configure and display using CLI commands.
Communication Machinery Corporation (CMC) The EmulationEngine is not joined with the SUT. 0 vSTAs currently in the system. CMC_EE -> The CLI is now ready to accept your commands. NOTE: If the CLI displays the message “This EmulationEngine has not been Node Locked” after you enter the EE login name and password, see “Missing Key File” in Chapter 9. Troubleshooting.
EmulationEngine 11a/b/g User's Guide get eestatus -- Display EmulationEngine status get evlog -- Display event log data get features -- Display authorized features get fragmentthreshold -- Display Fragment Threshold get frequency -- Display Radio Frequency (MHz) get gateway -- Display Gateway IP Address get group -- Display information for a vSTA group get hardware -- Display Hardware Revisions get ipaddr -- Display IP Address get ipmask -- Display IP Subnet Mask get key -- Display Encryption Key get keyen
Communication Machinery Corporation (CMC) set features -- Upgrade current feature set set fragmentthreshold -- Set Fragment Threshold set gdraft5 -- Set 11g Draft 5.
EmulationEngine 11a/b/g User's Guide 2) If the new System Under Test is not in the EmulationEngine's BSS list, a scan is required: scan 3) Use the set bssid command to set the EmulationEngine to another System Under Test: set bssid 4) Use the join command to join with the System Under Test: join 5) Issue the authenticate command for all virtual stations: auth vsta all 6) Issue the associate command for all virtual stations: assoc vsta all 7) Run the test for all virtual statio
Communication Machinery Corporation (CMC) clear bssid This command clears the current BSSID. clear bssid Example: CMC_EE -> clear bssid BSSID 00:04:e2:34:e0:a8 cleared use the set bssid CLI command to set the BSSID of the System Under Test CMC_EE -> bsslist (get) This command shows the Basic Service Sets discovered in the most recent scan. See the scan command. get bsslist Example: CMC_EE -> get bsslist BSS Type Channel RSSI BSSID -------- ---------- ----SUT BSS 5.
EmulationEngine 11a/b/g User's Guide See “set wirelessmode” to change the EmulationEngine’s wireless mode. NOTE: If a test is in process (see the run command), a scan operation will be disruptive to the normal testing operations of the EmulationEngine. CMC_EE -> scan Active (probe request) or passive (listen for beacons) [a/p: p]? Enter "a" and press the key to select an active scan. Just press the key to select the default passive mode.
Communication Machinery Corporation (CMC) vSTA ID:0 NOTIFY Operation SCAN succeeded. - WED JUL 09 10:12:19 2003 wirelessmode (get/set) get wirelessmode This command displays the current Wireless LAN Mode (11a, 11b, or 11g): get wirelessmode Example: CMC_EE -> get wirelessmode Wireless LAN Mode: 11g CMC_EE -> set wirelessmode This command sets the EmulationEngine’s Wireless LAN Mode: set wirelessmode : 11a = 802.11a, 11b = 802.11b, or 11g = 802.11g. The default value is 11g.
EmulationEngine 11a/b/g User's Guide Most of the commands in this group require that you join with a System Under Test. If a join or scan has not been done, the CLI will display the following message: ** **You must do a "join" or a "scan" with the join option first. ** Use the System Under Test commands described above to join with a System Under Test before using the commands in this group.
Communication Machinery Corporation (CMC) Null: The virtual station does not yet exist, it hasn't been created (i.e., configured). Configured: The initial configuration parameters for the virtual station have been defined. Initialized: The virtual station has been added to the system's internal tables (addressing, etc.). Authenticated: The virtual station has been authenticated with the System Under Test. Associated: The virtual station has been associated with the System Under Test.
EmulationEngine 11a/b/g User's Guide : Virtual Station ID (1...64) or "all". If is set to "all" (i.e., auth vsta all), the authentication sequence is initiated for all virtual stations. The following command will initiate the authentication sequence for all virtual stations in a specified group. auth group : Group ID (1...
Communication Machinery Corporation (CMC) [group ]: Optional group ID number (1...64). [csmode persistent|non-persistent]: Connection mode (persistent or non-persistent). [retry ]: If csmode is presistent, this parameter specifies the Authentication/Association retry limit (1...2,147,483,647 or zero (=no retries)). [timeout ]: If csmode is presistent, this parameter specifies the Authentication/Association timeout in milliseconds (1...2,147,483,647 or zero (=immediate timeout)).
EmulationEngine 11a/b/g User's Guide vSTA ID:2 ASSOC NOTIFY OK CMC_EE -> CMC_EE -> autoconf ? vSTA Auto-Configuration Information Configured vSTAs ...... 2 Base IP Address ....... 10.1.35.150 Next IP Address ....... 10.1.35.152 Base MAC Address ...... 00:0b:cd:59:00:01 Next MAC Address ...... 00:0b:cd:59:00:03 CMC_EE -> NOTE: By default, all virtual stations that are created in the CLI are assigned to group 1. This can be changed using the “set vsta group ” command.
Communication Machinery Corporation (CMC) : Number of data bytes to be included in ICMP Echo Requests: 64...1024. Example: CMC_EE -> conf 3 10.1.40.20 00:0b:cd:59:00:01 internal ping 10.1.40.16 64000 1024 CMC_EE -> OK NOTE: By default, all virtual stations that are created in the CLI are assigned to group 1. This can be changed using the “set vsta group ” command. deauth This command initiates the de-authentication sequence for one or more virtual stations.
EmulationEngine 11a/b/g User's Guide Example: CMC_EE -> disassoc vsta 1 CMC_EE -> OK CMC_EE -> vSTA ID:1 NOTIFY Operation DISASSOC succeeded - TUE JUL 15 03:09:50 2003 CMC_EE -> group (clear/del/get/reset/save/set) These commands display and modify group configuration. Group commands are a convenient way to reference multiple virtual stations using a single command. For example, the "set group" command will assign the specified parameters to all virtual stations in the group.
Communication Machinery Corporation (CMC) get group This command retrieves and displays a configuration parameter or statistics for all virtual stations in a group. get group : Group Number (1...64). If is “summary”, you may specify “all” as the group number (i.e., get group all summary) to display summary statistics for all groups.
EmulationEngine 11a/b/g User's Guide CMC_EE -> reset group This command resets all virtual stations in a group to the Initialized state and clears all group statistics counters. reset group : Group Number (1...64) Example: CMC_EE -> reset group 1 5 vSTAs reset CMC_EE -> save group stats This command saves statistics information in a file for all virtual stations in a specified group. Each virtual station in the group is saved to its own file.
Communication Machinery Corporation (CMC) csmode Connection mode: persistent or non-persistent encryption Encryption mode: on or off keyindex Shared-key index: 1, 2, 3, or 4 lp Load Protocol: ping mode external or internal retry Authentication/Association retry limit: 1...2,147,483,647 or zero (=no retries) size Ping Packet Size: 64...1024 target Ping Target IP address in ASCII Dotted Decimal Notation: nnn.nnn.nnn.nnn (e.g., 10.1.35.100).
EmulationEngine 11a/b/g User's Guide "conf" command. The following command initializes one or all virtual stations. init vsta : Virtual Station ID (1...64) or "all". If is set to "all" (i.e., init vsta all), all virtual stations are initialized. The following command initializes all virtual stations in a specified group. init group : Group ID (1...64) Example: CMC_EE -> init vsta 1 CMC_EE -> OK run This command starts running the load application for one or more virtual stations.
Communication Machinery Corporation (CMC) : Virtual Station ID (1...64), "all", or "master". If is set to "all" (i.e., clear vsta all stats), this command will clear all statistics for all virtual stations. If is set to "master" (i.e., clear vsta master stats), this command will clear all statistics for the EmulationEngine.
EmulationEngine 11a/b/g User's Guide keyindex: Display the virtual station’s shared-key index (1, 2, 3, or 4). lp: Display the virtual station’s Load Protocol (ping). mode: Display the virtual station’s test mode (external or internal). retry: If csmode is persistent, display the virtual station’s Authentication/Association retry limit (1...2,147,483,647 or zero (=no retries)). size: If the virtual station’s test mode is internal, display the configured ping packet size (64...1024).
Communication Machinery Corporation (CMC) vStaPingXmt:Active CMC_EE -> CMC_EE -> get vsta 1 stats vSTA 1: MAC 00:0b:cd:59:00:01, IP 10.1.35.
EmulationEngine 11a/b/g User's Guide Tx Retries Rcv Errors: Rcv PHY Errors: Rcv CRC Errors: Rcv Duplicates: Rcv Discarded: Ack Rcv Fails: Rcv Decrypt Errs: 0 0, 0, 0, 3, 0, 0, 0, 0 0 Tx Errors: Excess Retries: Total Retries: Tx Filtered: Tx Discarded: RTS Fails: WEP Excluded: FCS Fails: 0 0 0 0 0 0 0 0 0 reset vsta This command resets virtual stations to the Initialized state and clears the virtual station's statistics counters. reset vsta : Virtual Station ID (1...64) or "all".
Communication Machinery Corporation (CMC) set vsta : Virtual Station ID (1...64). If is anything other than "ip" or "mac", the can be given as "all" to apply the configuration parameter to all virtual stations. : authentication, cipher, count, csmode, encryption, group, ip, keyindex, lp, mac, mode, retry, size, target, timeout. : Depending on the , set to one of the following.
EmulationEngine 11a/b/g User's Guide CMC_EE CMC_EE CMC_EE CMC_EE CMC_EE -> -> -> -> -> OK set vsta 1 csmode persistent OK set vsta 1 csmode non-persistent OK Statistics File Commands The following commands can be used to display and delete statistics files: del del get get statfile summfile statfile summfile ----- Delete a vSTA statistics file Delete a vSTA statistics summary file Display vSTA statistics from file Display vSTA statistics summary from file See "Chapter 8, Statistics Counters" for a d
Communication Machinery Corporation (CMC) del summfile vsta all This command deletes the overall summary statistics file for all virtual stations. del vsta all summfile Get/Display Statistics File get statfile group This command retrieves and displays a statistics file for all virtual stations in a specified group. get statfile group : Group ID (1...64) get statfile vsta This command retrieves and displays a statistics file for one or more virtual stations.
EmulationEngine 11a/b/g User's Guide Clear Event Log clear evlog buffer This command clears the EmulationEngine's event log buffer. clear evlog buffer Example: CMC_EE -> clear evlog buffer clear evlog file This command clears a log file. clear evlog file : A or B Example: CMC_EE -> clear evlog file A Get/Display Event Log get evlog buffer This command displays event log data from the event log buffer. get evlog buffer : the number of records to display.
Communication Machinery Corporation (CMC) : The number of records to display. Omit this parameter to show all remaining records in the file. This parameter can only be used if is specified. Use "?" to display the number of records in the file. Example: CMC_EE -> get evlog file A ? Log file A has 15 records CMC_EE -> get evlog file A 1/1/1970,0:00:37,30.963149,0, CLI: set date 5/5/2003 15:21 5/5/2003,15:21:03,34.229892,1, CLI: (null) 5/5/2003,15:21:21,52.663185,2, CLI: autoconf 5 ip 10.1.
EmulationEngine 11a/b/g User's Guide NOTE: When logging to file is enabled (i.e., set evlog file enable), event records are automatically written to the log file as they occur. The "save evlog" command is intended for use when log to file is not enabled but there are significant events in the event log buffer that you want to save to file. Set Event Log Controls set evlog This command enables/disables event logging.
Communication Machinery Corporation (CMC) set evlog module : WLANTX = 802.11 WLAN frame transmissions, WLANRX = 802.11 WLAN frame receptions, EE = EmulationEngine control, VSTA = Virtual station control, UI = User interface actions : enable/disable Example: CMC_EE -> set evlog module EE enable EmulationEngine Commands The commands in this group can be used to display and modify the EmulationEngine configuration.
EmulationEngine 11a/b/g User's Guide set features -- Upgrade current feature set set fragmentthreshold -- Set Fragment Threshold set gateway -- Set Gateway IP Address set hwtxretries – Set HW Transmit Retry Limit set ipaddr -- Set IP Address set ipmask -- Set IP Subnet Mask set key -- Set Encryption Key set keyentrymethod -- Select Encryption Key Entry Method set login -- Modify Login User Name set password -- Modify Password set power -- Set Transmit Power set rate -- Set Data Rate set sntpserver -- Set S
Communication Machinery Corporation (CMC) channel (get) This command displays the radio channel/frequency used by the EmulationEngine. The channel is set automatically when it joins with the System Under Test. get channel Example: CMC_EE -> get channel Radio Frequency: 5260 MHz (IEEE 52) CMC_EE -> config (get) This command displays the EmulationEngine configuration. get config Example: This example shows the default configuration.
EmulationEngine 11a/b/g User's Guide set countrycode This command sets the country code configuration parameter for the EmulationEngine. set : An ISO standard country code (e.g., DB DEBUG, NA - NO_COUNTRY_SET, PR - PUERTO_RICO, US UNITED_STATES, etc.) Example: CMC_EE -> set countrycode us Country Code: US ** **DO NOT REMOVE POWER FROM THE EmulationEngine! **Wait for the EE to update the configuration file in Flash **or use the "reboot" command for immediate update & reboot.
Communication Machinery Corporation (CMC) EmulationEngine, use WLAN MAC Address: 04:0d:e0:62:23:57 and on the second EmulationEngine, use WLAN MAC Address: 06:0f:14:62:32:a0. This address and the WLAN MAC Mask (see “set eemask”) limits the range of MAC addresses that can be assigned to virtual stations.
EmulationEngine 11a/b/g User's Guide get eemask This command displays the Wireless LAN Address Mask: get eemask Example: CMC_EE -> get eemask WLAN Address Mask: ff:ff:ff:ff:00:00 CMC_EE -> set eemask This command sets the Wireless LAN Address Mask: set eemask : a valid address mask (e.g., ff:ff:ff:ff:00:00) eestatus (get) This command displays a high-level summary of the EmulationEngine's current status.
Communication Machinery Corporation (CMC) 0 00:04:E2:38:56:78 SUT 00:04:E2:38:A8:D2 CMC_EE -> up up NOTE: You must use the "ftp" command to upload the command file to the EmulationEngine's flash file system. factorydefault (set) This command restores the EmulationEngine configuration to default factory settings. set factorydefault NOTE: The example with the get config command shows the EmulationEngine's factory default configuration.
EmulationEngine 11a/b/g User's Guide This command is only used when you upgrade the EmulationEngine software with new features (i.e., from 802.11a to 802.11b or from 802.11a or 11b to 802.11a/b/g). fragmentthreshold (get/set) get fragmentthreshold This command displays the current fragmentation length threshold setting (256...2346): get fragmentthreshold set fragmentthreshold This command sets the fragmentation length threshold (i.e., the size at which an 802.11 frame is transmitted fragmented).
Communication Machinery Corporation (CMC) CMC_EE -> ftp 10.1.35.67 Username: Password: Remote File: I:\Engineering\EE\SW\Release\2.0.0\EE22.SYS Local File: EE22NEW.SYS download or upload: download Getting @10.1.35.67:I:\Engineering\LoadGenerator\Software\Release\2 .0.0\EE2 SYS -> EE22NEW.
EmulationEngine 11a/b/g User's Guide Example: CMC_EE -> get hardware wlan0: PCI Vendor ID: 0x168c, Device ID: 0x13 Sub Vendor ID: 0x168c, Sub Device ID: 0x2026 wlan revisions: mac 5.6 phy 4.1 analog 1.7 CMC_EE -> help This command displays all commands that are available in the CLI command set. help history The command displays the last 20 commands that were entered in the CLI. history Example: CMC_EE -> history 1 set date 2/4/03 11:09:30 2 join 3 autoconf 2 ip 10.1.35.
Communication Machinery Corporation (CMC) get ipaddr Example: CMC_EE -> get ipaddr IP Address: 10.10.10.46 CMC_EE -> set ipaddr This command sets the EmulationEngine's IP address. set ipaddr : A valid IP address in ASCII dotted-decimal notation (nn.nn.nn.nn). ipmask (get/set) get ipmask This command displays the EmulationEngine's IP subnet mask. get ipmask Example: CMC_EE -> get ipmask IP Subnet Mask: 255.255.0.
EmulationEngine 11a/b/g User's Guide set key This command sets an encryption key or default shared key.
Communication Machinery Corporation (CMC) Example: CMC_EE -> set login Your_User_Name Login Username: Your_User_Name CMC_EE -> password (set) This command sets the password that will be required to log in into the EmulationEngine command line interface and web-based user interface. Type the new password twice to confirm the use of the new password. The password is a text string and can be up to 32 characters. Control characters are not permitted. The password is case sensitive.
EmulationEngine 11a/b/g User's Guide set power This command sets the transmit power setting: full, half, quarter, eighth, or minimum. A lower setting will reduce the range of the EmulationEngine. set power : full - Set maximum (normal) transmit power (18 dBm/64 mW) half - Set fractional (1/2) transmit power (15 dBm/31.
Communication Machinery Corporation (CMC) rate, the EmulationEngine attempts to deliver unicast data packets at the highest possible optimum data rate. If there are obstacles or interference, the EmulationEngine automatically steps down to an optimum data rate that supports reliable data transmission. In addition, the optimum data rate is adjusted periodically based on past performance of the data transmissions at different neighboring data rates. set rate : If the wireless mode is 802.
EmulationEngine 11a/b/g User's Guide set rtsthreshold : 1...2346 sntpserver (get/set/clear) clear sntpserver This command clears the IP Address of the SNTP server. clear sntpserver get sntpserver This command displays the IP Address of the SNTP server. get sntpserver set sntpserver This command sets the SNTP server address. If an SNTP server address is configured, the EmulationEngine will attempt to retrieve the time from that server during initialization.
Communication Machinery Corporation (CMC) get systemname set systemname This command sets the EmulationEngine system name. It can be up to 32 characters. Control characters are not allowed. set systemname : up to 32 printable characters telnet (get/set) get telnet This command displays the telnet mode and the current state of telnet connections.
EmulationEngine 11a/b/g User's Guide Use the "set date" or "set time" command to adjust CMC_EE -> tzone (get/set) get tzone This command shows the current time zone setting. get tzone Example: CMC_EE -> get tzone SNTP/NTP Time Zone: -8 CMC_EE -> set tzone This command sets the local time zone. If no time zone is defined, GMT time is used. For example, use "set tzone -8" to set the time zone for the west coast of North America. set tzone : -12...
Communication Machinery Corporation (CMC) 802.11b/g Commands The following commands are only available when the wireless mode is set to 802.11b or 802.11g. get get get get get get get set set set set set set set basic11b -- Display Basic 11b Rates ctsmode -- Display CTS mode (11g) ctsrate -- Display CTS rate (11g) ctstype -- Display CTS type (11g) gdraft5 -– Display 11g Draft 5.
EmulationEngine 11a/b/g User's Guide communicate. When CTS protection mode is enabled (mode = always or auto), the EmulationEngine will use RTS/CTS (as defined by “ctstype”) to communicate with an 11b device.
Communication Machinery Corporation (CMC) set ctstype : cts-only = before transmission the EmulationEngine will transmit a CTS frame or rts-cts = transmission will follow an RTS/CTS frame exchange. gdraft5 (get/set) get gdraft5 (11g only) This command displays the current 11g Draft 5.0 compatibility setting: get gdraft5 Example: CMC_EE -> get gdraft5 11g Draft 5.0 compatibility: Disabled CMC_EE -> set gdraft5 (11g only) This command sets the 11g Draft 5.
EmulationEngine 11a/b/g User's Guide get shortslottime Example: CMC_EE -> get shortslottime Short Slot Time: Enabled CMC_EE -> set shortslottime (11g only) This command enables/disables Short Slot Time (11g) Usage. When enabled, the EmulationEngine will advertise using 9 millisecond slot times. When disabled, the EmulationEngine will advertise using 20 millisecond slot times. set shortslottime : enable = Enable Short Slot Time (G mode), disable = Disable Short Slot Time (use only long).
Communication Machinery Corporation (CMC) CMC_EE -> You must use the admin command to activate administrative mode before using any of the commands listed in this table. admin (clear) This command is used to activate and deactivate administrative mode. Enter "admin" and the administrative mode password (cmc) to activate administrative mode. The password is case sensitive (use "cmc", not "CMC"). Enter "clear admin" and press to deactivate administrative mode.
EmulationEngine 11a/b/g User's Guide : The name of an image file (.sys) to use to boot the EmulationEngine. : If is ethernet, the name of the host computer where resides. : If is ethernet, the IP address of the host computer where resides. : If is ethernet, the username required to access . : If is ethernet, the password required to access . Examples: CMC_EE -> boot flash EE22.
Communication Machinery Corporation (CMC) calibration (get/set) To ensure performance of the EmulationEngine over temperature and environment changes, the software performs periodic calibration. get calibration This command displays the current calibration period. get calibration Example: CMC_EE -> get calibration Calibration time: 60 seconds CMC_EE -> set calibration This command sets the current calibration period. CMC_EE -> set calibration = 0...
EmulationEngine 11a/b/g User's Guide Example: CMC_EE -> ls Directory listing of ".": 2/18/2003 17:12:24 1009597 12/01/2002 9:03:32
12/06/2002 11:03:06 1/21/2003 14:06:00 598 3/05/2003 12:27:24 598 11/21/2002 8:33:02 11/21/2002 10:01:36 4 directories, 5 files 1839104 bytes free EE22.SYS Scenarios Statistics eecfg.bak eecfg Logs Scripts mv This command renames a file in the EmulationEngine's flash file system.Communication Machinery Corporation (CMC) dsi = Toggle DS In debug trace function arp = Toggle ARP debug trace function show = Display EE debug trace status NOTE: If you are running a log generator tool, do not enable "trace all”. This will cause numerous “printf” statements to be generated in the background and the EmulationEngine will malfunction. translate This command enables or disables virtual station ATL (Address Translation Logic).
EmulationEngine 11a/b/g User's Guide The default IP address of your EmulationEngine is 192.168.0.50. For the initial configuration of your EmulationEngine, use the provided crossover Ethernet cable to establish a direct connection between a PC and the EmulationEngine. The PC must also be configured with an IP addresses in the 192.168.0.xxx range. You may then use telnet on the PC to login to the EmulationEngine and use the CLI to set the desired configuration parameters.
Communication Machinery Corporation (CMC) Example Security Configuration Step 1: Configure the virtual station. CMC_EE -> conf 1 10.1.40.18 04:cf:1f:00:00:01 internal ping 10.1.40.16 10 1000000 1024 CMC_EE -> OK CMC_EE -> get vsta 1 vSTA configuration: ID ...................... Group ID ................ IP Address .............. MAC Address ............. Connection Mode ......... Auth/Assoc Retry ........ Auth/Assoc Timeout ...... Authentication .......... Cipher .................. Data encryption ........
EmulationEngine 11a/b/g User's Guide Ping data size .......... 1024 CMC_EE -> Step 5: Use the following command to turn on authentication using shared keys. CMC_EE -> set vsta 1 authentication shared-key CMC_EE -> OK NOTE: Virtual stations could have authentication using shared static key or data encryption using shared static key or both. Only WEP cipher is available.
Communication Machinery Corporation (CMC) Select/highlight Internet Protocol (TCP/IP). Click the Properties button to display the Internet Protocol (TCP/IP) Properties dialog. 6-60 Rev #/Date: 2.0.0 Beta/07.17.
EmulationEngine 11a/b/g User's Guide Select the “Use the following IP address” radio button and enter the IP address for the Ethernet connection. Use an IP Address that resides on the same IP subnet as the EmulationEngine. For example, use 192.168.0.2 if you are using the EmulationEngine's default IP address 192.168.0.50. Click “OK” to close the Internet Protocol (TCP/IP) Properties dialog. Click the Close button in the Local Area Connection Properties dialog.
Communication Machinery Corporation (CMC) EE login: Admin Password: ** The default log in name is Admin. The default password is EE. Following successful log in, the CLI will display the log in banner: Communication Machinery Corporation EmulationEngine(tm) 11a/b/g Rev 2.0.0.a1 System date & time is THU JAN 01 00:00:44 1970 Use the "set date" or "set time" command to adjust EmulationEngine 11a/b/g software version 2.0.0 WLAN mode .................... 802.11b WLAN MAC address .............
EmulationEngine 11a/b/g User's Guide CLI Editor After you have entered one or more CLI commands, press the key to enter edit mode. In edit mode, you can use UNIX vistyle commands to quickly navigate, edit and resubmit previous CLI commands. Use the history (hi) command to show a history of the last up-to-20 commands. Movement & Search Commands In the following commands, the default value for n is 1 Command Description nG Go to command number n (e.g.
Communication Machinery Corporation (CMC) cl Change character. cw Change word. cc or S Change entire line. c$ or C Change everything from cursor to end of line. i Insert. I Insert at beginning of line. R Type over characters. Editing Commands In the following commands, the default value for n is 1 6-64 Command Description nrc Replace the following n characters with c. nx Delete n characters starting at cursor. nX Delete n characters to the left of the cursor.
EmulationEngine 11a/b/g User's Guide Special Commands Command Description CTRL-U - Delete line and leave edit mode. CTRL-L - Redraw line. CTRL-D - Complete symbol name. RETURN - Give line to shell and leave edit mode. Rev #/Date: 2.0.0 Beta/07.17.
Communication Machinery Corporation (CMC) 6-66 Rev #/Date: 2.0.0 Beta/07.17.
