Optional Direct Connect Remote Antenna Installation Remote antenna installation is complete.
APPENDIX A Using an Inline Connector This section describes the 100W/100W+ and 100WP/100WP+ ERT module connections to the water meter register using the inline connector assembly. Follow the manufacturer's recommended procedure for installing the water meter register on the meter. To connect the inline connector Note If an inline connector is not used and the ERT module is already connected to the water meter register, skip this step. 1.
Using an Inline Connector 3. Install the security seal as shown. Push it until it snaps into place. Note For future meter or ERT module servicing, break the security seal by pulling the seal apart. The original protective connector covers can be reused if kept clean and dry. Install a new security seal after servicing either device. To order replacement security seals, see the Water ERT Module Ordering Guide (PUB-0063-001).
APPENDIX B Using the Itron Splice Kit This section describes connecting the 100W/100W+ and 100WP/100WP+ ERT module with flying leads to the water meter register using the Itron Splice Kit. Caution ERT module wire terminations must be properly sealed with a non-conductive gel material to prevent water intrusion (otherwise, this configuration should not be used in a pit box environment). Itron recommends the 5-foot or 20-inch cable configuration for OEM users only.
Using the Itron Splice Kit 2. Carefully place the connector and wires into the jaws of the crimping tool. Make sure the wires remain fully inserted in the gel-cap connector. 3. Crimp the connector by squeezing the handles until the connector cap is fully seated. Continue to apply pressure for three seconds. 4. A connector is crimped properly when the top of the movable yellow center (1) is flush with the top of the connector body (2). Warning Crimping the connector forces some sealant out of connector.
Using the Itron Splice Kit 5. After you complete all ERT module to register wire connections, arrange the connectors in a single file. 6. Insert the connectors and wires into the splice tube until the connectors and wires completely immerse in the tube's gel material. 7. Separate the cables to the sides and close the splice tube cover. 8. Discard any leftover materials from the customer premises.
APPENDIX C Using the Itron Cable Armor This section describes the procedure for installing Itron cable armor in a field installation. The Itron armor cable provides a layer of protection for the module's cable jacket. Itron cable armor is available in 5-foot sections. Warning Itron armor cable is stainless steel and may have sharp edges. Use caution when you are installing the armor cable.
Using the Itron Cable Armor 3. Wrap the entire piece of electrical tape around the ERT module cable near the inline connector. 4. Beginning over the installed electrical tape, twist the Itron cable armor onto the ERT module cable using a right-handed twist. Important You must twist—not wrap—the cable armor onto the ERT module cable. Wrapping the cable armor can cause the stainless steel jacket to warp.
APPENDIX D Troubleshooting The following information is provided to help you troubleshoot issues related to the 100W/100W+ and 100WP/100WP+ ERT modules. The following table describes possible issues and provides suggested actions to resolve the issue. Issue Action Cannot program the ERT module. Check the programming device and software version. Program ERT modules using the FC300 handheld computer running Field Deployment Manager (FDM) software. Cannot read the ERT module.
Index Symbols & Numbers 100W/100W+ and 100WP/100WP+ ERT Module installation • Error! Bookmark not defined. 100W/100W+ and 100WP/100WP+ ERT Module models • Error! Bookmark not defined., Error! Bookmark not defined. 100W/100W+ and 100WP/100WP+ ERT Module transmission modes • Error! Bookmark not defined. 100W/100W+ and 100WP/100WP+ ERT Module with integral connectors • Error! Bookmark not defined. 100W/100W+ encoder start-up • Error! Bookmark not defined.
Index using an inline connector • Error! Bookmark not defined. using the Itron splice kit • Error! Bookmark not defined. V verifying 100W/100W+ and 100WP/100WP+ ERT Module operation • Error! Bookmark not defined.