Specifications

ManualsBrandsiTon ManualsElectronicsBluetooth 4.1 data module

本檔案是商業機密，未經事先同意，不得向第三方廠商透露。此處提供的資訊被認為是可靠的，但生產測試可能不包括

所有參數的測試。中易騰達科技股份有限公司保留在沒有通知的情況下隨時更改資訊的權利。

This document contains information that is proprietary to ITON Technology Corp. This document is commercially confidential and

must NOT be disclosed to third parties without prior consent. The information provided herein is believed to be reliable. But

production testing may not include testing of all parameters. ITON Technology Corp. reserves the right to change information at any

time without notification.

STB1132-25

Module Specification

Ver1.0.0

IC:5528A-DDX50R03

Summary of content (17 pages)

PAGE 1
STB1132-25 Module Specification Ver1.0.0 IC:5528A-DDX50R03 ©2016-2017 ITON Technology Corp. 本檔案是商業機密，未經事先同意，不得向第三方廠商透露。此處提供的資訊被認為是可靠的，但生產測試可能不包括所有參數的測試。中易騰達科技股份有限公司保留在沒有通知的情況下隨時更改資訊的權利。 This document contains information that is proprietary to ITON Technology Corp. This document is commercially confidential and must NOT be disclosed to third parties without prior consent. The information provided herein is believed to be reliable. But production testing may not include testing of all parameters.
PAGE 2
深圳市中易腾达科技股份有限公司 iTON Technology Corp. STB1132-25 Contents Version:.................................................................................................................................................3 1. Overview..........................................................................................................................................4 1.1 Brief........................................................................................................................................
PAGE 3
深圳市中易腾达科技股份有限公司 iTON Technology Corp. STB1132-25 Version: Data Version 2017-02-15 V0.01 Edit Draft Kain Revised 2.2 PIN assignment 2017-03-07 V0.02 Kain 2.3 PIN description 2.4 Schematic diagram 2017-3-20 V0.03 Revised DIO12 description Kain 2017-4-13 V1.00 Released version Kain http://www.sziton.
PAGE 4
深圳市中易腾达科技股份有限公司 iTON Technology Corp. STB1132-25 1. Overview 1.1 Brief Bluetooth module STB1132-25 base on ST newest LE4.1 chipset BlueNRG1, establish a bidirectional data transfer channel through UART interface between mobile phone and client's MCU. According to the content of commands list, Client's MCU may send the corresponding commands to set the Bluetooth module into different condition, or send or receive data on GATT layer, Bluetooth module's status also can be read through commands. 1.
PAGE 5
深圳市中易腾达科技股份有限公司 iTON Technology Corp. STB1132-25 2. Hardware System 2.1 Function block STB1132-25 http://www.sziton.
PAGE 6
深圳市中易腾达科技股份有限公司 iTON Technology Corp. 2.2 STB1132-25 PIN assignment 2.3 PIN description No. Name Description 1 SXTAL0 32.768KHz Xtal 2 SXTAL1 32.768KHz Xtal 3 GND POWER 4 DIO6 I/O 5 DIO7 I/O 6 GND POWER 7 SWCLK/DIO9 Software download PIN 8 SWDIO/DIO10 Software download PIN 9 DIO14 I/O 10 VBAT POWER 11 REST Module hardware reset 12 ADC1 I/O http://www.sziton.
PAGE 7
深圳市中易腾达科技股份有限公司 iTON Technology Corp. 13 ADC2 STB1132-25 I/O When module in sleep, 14 DIO13/Wake-up lower level this PIN to wake Pull down duration≥50ms up module 15 DIO12 I/O 16 GND POWER 17 DIO0 I/0 18 UART_RX UART RX PIN 19 UART_TX UART TX PIN 20 DIO4 I/O 21 DIO5 I/O Mode select PIN 22 DIO3/Mode_N H: Data mode Default: H L: Command mode 23 24 25 2.
PAGE 8
深圳市中易腾达科技股份有限公司 iTON Technology Corp. STB1132-25 Note: 1) 32.768KHz may save 2uA power consumption in Sleep mode, do not connect if not necessary. 2) Wake-up PIN is used to wake-up the module when it enter low power mode, please connect to MCU GPIO through pull-up resister R5. If this MCU GPIO with Pull-up function, then may connect to wake-up Pin directly. 3) Mode-IN PIN is used to switch module between pure data mode & command mode, please connect to MCU GPIO through Pull-up resister R2.
PAGE 9
深圳市中易腾达科技股份有限公司 iTON Technology Corp. STB1132-25 2.5.2 Maximum parameter Item Min. Max. Unit VCC voltage -0.3 3.9 V Working temperature -20 75 ℃ Storage temperature -30 85 ℃ Working range TBD. TBD. a note：VCC=3.0v, data flow 2Kbyte/s, under open environment 2.5.3 Working Voltage Item Min. Typ. Max. Unit VCC Voltage 1.7 3.0 3.6 V 2.5.4 Working Current Test condition: Vcc=3.0v@，Ta=25℃ Mode Current（Avg.） Unit Sleep Mode 5 uA 40 uA 57 uA 400 uA 79 uA 2.39 mA 2.
PAGE 10
深圳市中易腾达科技股份有限公司 iTON Technology Corp. STB1132-25 2.5.5 External Crystal SB1132-20 may be connected with external 32.768KHz crystal, this may save about 2uA power consumption in sleep mode. Crystal request as below: Item Parameter Min. Nominal fNOM Typ. 32.768 frequency Frequency fTOL Max. tolerance Unit KHz ±50 ppm 90 kΩ 0.1 µW Max. Unit Equivalent ESR series resistance PD Drive level 2.5.6 TX parameter Item Min. Typ.
PAGE 11
深圳市中易腾达科技股份有限公司 iTON Technology Corp. 2.6 STB1132-25 Dimensions 2.6.1 Mechanical dimensions http://www.sziton.
PAGE 12
深圳市中易腾达科技股份有限公司 iTON Technology Corp. 2.6.2 STB1132-25 Layout reference dimensions Layout note: The ANT area please keep clearance, do not routing & copper. Filter CAP please place close to module. Non strong interference line under module. http://www.sziton.
PAGE 13
深圳市中易腾达科技股份有限公司 iTON Technology Corp. STB1132-25 3. Process parameters 3.1 Recommended temperature curve Referred to IPC/JEDEC standard. Peak Temperature : <250°C Number of Times : ≤2 times 4. Package information TBD http://www.sziton.
PAGE 14
深圳市中易腾达科技股份有限公司 iTON Technology Corp. STB1132-25 5. Please be noticed following information and instructions should be placed in the end-user’s operating manual The MODEL STB1132 has been granted as limited modular approval for mobile applications. MODEL STB1132 must be installed in the designated host as specified in this manual. 1. Separate approval is required for all other operating configurations, including portable configurations with respect to 2.1093 and different antenna configurations. 2.
PAGE 15
深圳市中易腾达科技股份有限公司 iTON Technology Corp. STB1132-25 6. Separate approval is required for all other operating configurations, including portable configurations with respect to FCC Part 2.1093 and different antenna configurations. 7. A certified modular has the option to use a permanently affixed label, or an electronic label. For a permanently affixed label, the module must be labelled with an FCC ID: 2AJ22STB1132.
PAGE 16
深圳市中易腾达科技股份有限公司 iTON Technology Corp. STB1132-25 6. FCC Certification Requirement: The end product with an embedded - MODEL STB1132 may also need to pass the FCC Part 15 unintentional emission testing requirements and be properly authorized per FCC Part 15. Note: If this module is intended for use in a portable device, you are responsible for separate approval to satisfy the SAR requirements of FCC Part 2.1093. This device complies with Part 15 of the FCC Rules.
PAGE 17
Operation is Subject to the following two conditions: (1) this device may not cause interference. (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.