User's Manual
2 3 4 5 6
1201799
User’s Guide
RadioShack
Bluetooth® Music Receiver
We hope you enjoy your RadioShack Bluetooth
®
Music
Receiver. This receiver enables wireless streaming of music
from your Bluetooth enabled device to your home audio
system. Please read this user's guide before using your
receiver.
Package Contents
• RadioShack Bluetooth
®
Music Receiver
• AC Adapter
• 6ft (1.82m) ⅛" (3.5mm) Audio Cable
• 6ft (1.82m) RCA Cable
• User’s Guide
Changing Bluetooth Devices
To pair a new device, you must disconnect your device's
Bluetooth connection with the receiver rst. Press the
connect button twice, the LED on the receiver ashes blue
and red. Follow the instructions in "Pairing" to connect to a
new device.
Specifications
Power ................................................................................ 5V DC 300mA
Bluetooth Protocol ..................................................V4.1 + EDR A2DP
Operation Range ................................................................ 33 ft. (10m)
Specifications are subject to change and improvement
without notice. Actual product may vary from the images
found in this document.
FCC Information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that
to which the receiver is connected.
• Consult your local dealer or an experienced radio/TV technician for
help.
If you cannot eliminate the interference, the FCC requires that you stop
using your equipment. Changes or modications not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
Complies with the European Union’s
“Restriction of Hazardous Substances
Directive,” which protects the
environment by restricting specic
hazardous materials and products.
12A16
1201799
Printed
in China
© 2016 General Wireless Operations Inc.
All rights reserved. RadioShack is a registered
trademark used by General Wireless
Operations Inc. dba RadioShack.
radioshack.com
This device complies with Part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Limited Warranty
Go to www.radioshack.com/help for details.
RadioShack Customer Relations
300 RadioShack Circle, Fort Worth, TX 76102
Setup
1. For analog output:
Connect the ⅛" (3.5mm) plug on the RCA cable (included)
into the AUX OUT jack on the receiver, then plug the RCA
plugs into the AUX IN jacks on your amplier.
OR
Connect one end of the ⅛" (3.5mm) audio cable
(included) into the AUX OUT jack on the receiver and
plug the other end into the line-in jack on your amplier.
For digital output:
Connect a TOSLINK cable (not included) into the
OPTICAL OUT jack on the receiver, then connect the
other end into the OPTICAL IN jack on your amplier.
2. Connect the adapter into the DC IN jack on the receiver
then plug the adapter into a wall outlet.
Pairing
LED Indicator
Flashes Blue - Standby
Flashes blue and red
alternatively - pairing mode
Lights blue steadily - paired
Connect Button
Press and hold to turn on/o
Press twice when receiver is
on to enter pairing mode
1. Press and hold the connect button to turn on the
receiver. The LED indicator ashes blue.
2. Activate the Bluetooth function on your Bluetooth-
enabled music source (see your device's user's guide for
details).
3. Press the connect button twice on the receiver to enter
pairing mode. The LED indicator ashes blue and red
alternatively as the receiver searches for a device.
4. On your Bluetooth music device, select RadioShack
1201799 from the device list to pair the receiver. When
your device is connected, the blue LED indicator stays
lit.
5. To turn o the receiver, press and hold the connect
button until the blue LED turns o.
Note: If your Bluetooth-enable device was previously paired
with the receiver, they will reconnect automatically once the
receiver is turned on.
OR
OR
DIGITAL
OPTICAL
IN
3.5mm
LINE-IN
AUX IN
R L
ANALOG
RCA Cable
Audio Cable
TOSLINK Cable
The Bluetooth
®
word mark and logos are owned by Bluetooth SIG,
Inc. and any use of such marks by General Wireless Operations
Inc. is under license.
1201799 UG_EN.112816.indd All Pages 12/2/2016 5:13:21 PM