User's Manual

2 3 4 5 6
1201786
User’s Guide
Bluetooth
®
Portable Transmitter
We hope you enjoy your Bluetooth Portable Transmitter from
RadioShack. This transmitter allows you to turn your non-
Bluetooth device into a Bluetooth-enabled device for wireless
streaming. Please read this user's guide before using your
transmitter.
Package Contents
• Bluetooth Portable Transmitter
• USB charging cable
• User’s Guide
Specifications
Battery Type...............................Built-in 300 mAh lithium polymer
Bluetooth Protocol...........................................................Version 2.1
Support Prole............................................................................A2DP
Operating Distance.........................................................33 ft. (10 m)
Battery Charge Time..............................................Approx. 3 Hours
Operating Time............................................................Up to 5 Hours
Charging Port......................................................................Micro USB
Charging Cable Length..................................................3 ft. (0.91m)
Specications are subject to change and improvement without
notice. Actual product may vary from the images found in this
document.
Complies with the European Union’s
“Restriction of Hazardous Substances
Directive,” which protects the
environment by restricting specic
hazardous materials and products.
12A16
1201786
Printed
in China
© 2016 General Wireless Operations Inc.
All rights reserved. RadioShack is a registered
trademark used by General Wireless
Operations Inc. dba RadioShack.
radioshack.com
The Bluetooth® word mark and logos are owned by Bluetooth
SIG, Inc. and any use of such marks by General Wireless
Operations Inc. is under license.
Charge
Notes:
• You can charge the transmitter when it is idle or in use.
• Transmitter battery is low when the red LED ashes every
8 seconds. Charge the transmitter.
• A full charge takes about 3 hours, and provides up to 5
hours play time.
• Unplug the charging cable when charging is complete. Do
not attempt to overcharge.
• Use only the supplied cable, or one with the same
specication to charge. Use of any other cables may
damage the transmitter.
Note:
• Turn o the transmitter when not in use. Press and hold
the transmitter button until the red LED ashes three
times.
• If your device is out of connection range and disconnects,
move back within 20 seconds to reconnect automatically.
• If you cannot reconnect the transmitter to your device,
restart the transmitter and repeat pairing mode again (see
"Pair a new device").
• If connection between transmitter and device is lost for
more than 20 seconds, the device will be deleted from the
memory. Pair as a new device again.
Changing Bluetooth Devices
The transmitter automatically reconnects to the most
recently paired device when switched on. To pair a new
device, you must disconnect your current device's Bluetooth
connection with the transmitter. With your transmitter and
device connected (LED lights blue), press the transmitter
button twice. The LEDs ash blue and red alternatively. Follow
the instructions in "Pair a new device" to connect to a new
device.
FCC Information
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment o and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Connect to
a USB power
source
Pairing
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
If you cannot eliminate the interference, the FCC requires that you
stop using your equipment. Changes or modications not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
Limited Warranty
Go to www.radioshack.com/help for details.
RadioShack Customer Relations
300 RadioShack Circle, Fort Worth, TX 76102
1/8" (3.5 mm)
audio input
jack
USB
Charging
Port
LEDs
Button
Non-Bluetooth
transmitting devices
Red LED
• lights during charging
• turns o when charging is complete
Bluetooth-enabled
receiving devices
Plug the transmitter into the ⅛" (3.5 mm) audio output port on
your stereo non-Bluetooth device before you start pairing.
Pair a new device:
1. Activate the Bluetooth function and enter pairing mode
on your Bluetooth-enabled stereo receiver device.
(Refer to your device's user's guide)
2. Press and hold the button on the transmitter for 3
seconds to turn on the transmitter. The transmitter
enters pairing mode and the red and blue LED ashes
alternatively as it searches to pair with a new device.
When paired, the blue LED lights steadily.
Pair a previously paired device:
1. Activate the Bluetooth function on your Bluetooth-
enabled stereo receiver device.
2. Press and hold the button on the transmitter for 3
seconds to turn on the transmitter. The LED ashes
blue while reconnecting to the device for 20 seconds.
When paired, the blue LED lights steadily.
1201786_UG_EN_A_111416_rev.indd All Pages 12/15/2016 11:37:14 AM