Quick Guide

ManualsBrandsiTALKPTT ManualsElectronicsPoC Radio

Appearance

iTALK-660 PoC Radio

Quick Guide

Please read before using this product

iTALKPTT Worldwide Communications

https://www.italkptt-international.com/

Items Instructions

Unpacking and Checking

ItemNo. ItemNo.

Up Side Key

PTT Key

Down Side Key

Emergency Alarm Key

Antenna

LED Indicator

Channel Knob

Power/Volume Knob

Display

Menu/Navigation Key

Speaker

Keypad

Microphone

Battery Latch

Connector Cover

Universal Connector

Hole for hand strap

Belt Clip

Battery

Battery Contacts

SIM Card Cover

Installing the Battery

1. Press the upper part of belt clip gently to lift it up.

2. Align the battery with the rails on the back of the radio, slide upward until the

lock position.

3. As shown in the figure below，Push the battery latch as shown in figure ①,

and then push it forward as shown in figure ② until the battery is locked.

Basic Operation

Uninstalling the Battery Installing SIM Card FCC Warning

Charging the Battery (Desktop charger )

1. Press the upper part of the belt clip gently to lift it up.

2. As shown in the figure below，Push the battery latch as shown in figure ①,

and then pull it backward as shown in figure ② and remove the battery.

1. Plug the power adapter into a qualified AC power socket.

2. Connect one end of the DC cable to the power adapter,and the other end to

the DC port at the back of the desktop charger. Green indicator light is on.

3. Insert the battery only or together with the radio into the desktop charger.

(Power off the radio)

4. Make sure the battery contacts the charging points properly and red indicator

light is on.

5. When the indicator light turns from red to green, the battery is full charged.

Friendly Reminder: Please use the standard Nano-SIM card. The sim card slots

are under the battery pack compartment.

1. Remove the battery and open the SIM card cover, then two sim card slots

appear, any one or two of which can be used.

2. Push down the cover on the SIM card slots in the direction of the OPEN arrow

and open.

3. Install the SIM card in the direction of the card slot guide angle and make sure

that the SIM card is installed correctly.

4. Close the SIM card cover and push up in the direction of the LOCK arrow to

the locking position.

15.19 Labeling requirements.

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that

may cause undesired operation.

15.21 Information to user.

Any Changes or modifications not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

15.105 Information to the user.

Note: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Absorption Rate (SAR) information:

This device meets the government's requirements for exposure to radio waves.

The guidelines are based on standards that were developed by independent

scientific organizations through periodic and thorough evaluation of scientific

studies. The standards include a substantial safety margin designed to assure

the safety of all persons regardless of age or health.

FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6

W/kg averaged over one gram of tissue. This device was tested for typical

body-worn operations with the back of the device kept 10mm from the body

without belt-clips, 0mm from the body with the belt-clips, 25mm from the face. To

maintain compliance with FCC RF exposure requirements, use accessories that

maintain a appropriate separation distance between the user's body and the back

of the device. The use of belt clips, holsters and similar accessories should not

contain metallic components in its assembly. The use of accessories that do not

satisfy these requirements may not comply with FCC RF exposure requirements,

and should be avoided. Use only the supplied or an approved antenna.

CE Warning

1. Risk of explosion if battery is replaced by an incorrect type. Dispose of used

batteries according to the instructions.

2. The product shall only be connected to a USB interface of version USB2.0 or

higher.

3. Adapter shall be installed near the equipment and shall be easily accessible.

4. The operating temperature of the device can’t exceed 40℃ and shouldn’t be

lower than -25℃.

5. The plug considered as disconnect device of adapter.

6. The device complies with RF specifications when the device used at 5mm from

the body without belt-clips, 0mm from the body with the belt-clips, 25mm from the

face.

7. Use careful with the earphone maybe possible excessive sound pressure from

earphones and headphones can cause hearing loss.

8. The band 5150-5350MHz indoor use only.

Hereby, iTALKPTT Worldwide Communications declares that this product is in

compliance with essential requirements and other relevant provisions of Directive

2014/53/EU. This product is allowed to be used in all EU member states.

Friendly Reminder: This product is a PoC Radio. The realization of all functions

such as calling, programmable keys and menu are related to the management

platform settings. For details, please contact your dealer.

This document is only for reference, and actual product prevails.

Our company reserves the right to the final interpretation of this document

Version：V1.0

Caution

1. Powering On/Off

1.1. When the radio is off, rotate the Power/Volume knob clockwise until a click

is heard to power on the radio.

1.2. When the radio is on, rotate the Power/Volume knob counterclockwise

until a click is heard to turn off the radio.

2. Adjusting the Volume

When the radio is on, rotate the Power/Volume knob clockwise to increase the

volume or counterclockwise to decrease it.

3. Switching Groups

After the radio registers successfully and enters standby state, rotate the

Channel knob to select a group.

4. Initiating Group Call

After switching to a group successfully (note: groups are set under the

management platform), press the PTT key to call the default contacts of the

current group.