USER’S MANUAL (IMPORTANT SAFETY INSTRUCTIONS & FCC NOTICE) (DT-1NEW Transmitter and BASE)
√ IMPORTANT SAFETY INSTRUCTIONS When using your equipment, basis safety precautions should always be followed to reduce the risk of life electric shock, and injury to persons, including the following. 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. 4.
14. Do not use the TRANSIMITTER to report a gas leak in the vicinity of the leak. √ SAFETY INFORMATIONS FOR DT-1NEW - This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. - This equipment must be installed and operated in accordance with provided instructions and hold the transmitter and antenna at least 0.5 inches (1.
√ IMPORTANT Read this manual before attempting to setup or use this instrument. If contains important Information regarding safe installation and use. Keep this manual for future reference. Also save the carton, packing and proof of purchase to simplify and accelerate any needed action. √ WARNING To prevent fire or shock hazard, do not expose this product to rain or any type of moisture. If accidentally dropped into water, this product should immediately by unplugged from the AC outlet jack.
7. 8. 9. 10. 11. " heating them. Sudden release of the battery electrolyte may occur, causing burns or irritation to eyes or skin. When inserting the battery into this product, the proper polarity or direction must be observed. Reverse insertion of battery may result in leakage or explosion. Remove the battery from this product if the product will not be used for a long period of time (several months or more) since during this time they could leak in the product.
3. Push the TALK button on the transmitter. When the antenna icon on the LED of the transmitter is displayed steadily, the communication channel between the BASE and transmitter has been setup and the transmitter is transmitting the audio signal. On the other hand, when the antenna icon blinks, the frequency channel between the BASE and transmitter does not match. Place the transmitter in its cradle on the BASE. Put Transmitter on the Receiver (Charging). Press and hold TR's talk button over 5 secs.
FCC NOTICE This DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDERSIRED PERATION. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
DT-1NEW 2.4GHz Frequency Hoping Digital TRANSMITTER AND Base INSTRUCTION MANUAL DT-1NEW consists of a Base and transmitter. Read these instructions carefully for correct use and retain it for reference in future. SYSTEM CONFIGURATION VCR Control Box BASE Station Transmitter • 95 channels are possible in the 2400~2483 MHz bandwidth. • Transmission range reaches up to 250 meters in free area. • NEW datatalker conforms to RF regulations of FCC part 15.
3. Select the ON position of power switch 4. After 5 seconds, Push the TALK button of the transmitter to check the operation. OPERATION 8. Supply 12 VDC power into the BASE (Docking-station) using the provided AC adaptor. 9. Separate the transmitter from the BASE (DS) and turn on the transmitter. 10. Push the TALK button on the transmitter.
Trouble Shooting Guide. 1. For initial use, Check line and power connection to the BASE (Docking-Station). And Select on position of the power switch (Transmitter) Please wait over 5~7 seconds (Need a time to find a BASE) And Push the talk button of the Transmitter to operation. 2. If you have a link failure and does not register with Transmitter and Docking Please disconnect the power of the Docking and reconnect the power of the Docking (Receiver). Try again link and registration.