Technologies HDDSrM HDDS CS650 6.
IMPORTANT SAFETY INSTRUCTIONS! Please read this very carefully before operating this unit Read ALL instructions carefully before using this unit. Do not operate this unit near water, in the rain, or where there is moisture. If this warning is ignored a serious electrical shock or death may occur. Do not attempt to service this unit. No user serviceable parts inside. Refer servicing to qualified, ISP approved service personnel.
INTRODUCTION Thank you for your purchase of the ISP Technologies High Definition Distributed System CS650 Surface Mount Speaker. This product provides a new level of performance in distributed audio systems allowing greater system flexibility and easy installation of distributed sound. All connections are made via Cat5 RJ45 connections making installation of systems faster and easier using the CS650. PRECAUTIONS NOTE: IT IS VERY IMPORTANT THAT YOU READ THIS SECTION TO PROVIDE YEARS OF TROUBLE FREE USE.
OPERATION The HDDS Master Control Module is the Master control center for distributed sound systems using the HDDS technology. The Master Control Module includes six zones that can be used independently or can be linked to work together allowing the system designer the flexibility to set up any system with the desired configuration. The block diagram below shows the basic configuration of the CS650 Surface Mount Speaker.
Rear of Speaker The rear of the CS650 Speaker includes three RJ45 connectors one for input and one for output and one that allows connection to one of three remote level control options, the RM10, RM20 or the RM20I. The CS650 also includes a power jack that allows connection to an external 18VAC power adaptor available from ISP Technologies if an external adaptor is required. Connect the input to the output connector on a HDDS Master Control Module.
Connect the CS650 to any of the A,B or C outputs on the rear of the HDDS Master Control Module as shown below. Internal Loudness Circuit The CS650 includes an on board switchable Loudness Circuit with the switch located on the right hand side of the Printed Circuit Board as shown in the picture above. When the switch in the OUT position the CS650 response is flat, when the switch is in the IN position a 6db increase in both Bass and Treble is applied.
Connections to the CS650 Speaker The CS650 bottom edge of the Printed Circuit Board contains three RJ45 connectors, providing INPUT, OUTPUT and REMOTE LEVEL connections. Connect the input RJ45 to the output of the HDDS Master Control Module Zone Output A, B or C. Connect the OUTPUT RJ45 connector to the next CS650 in the serially connected chain of speakers.
speaker CS650. Each of the three outputs A, B and C are capable of delivering up to 7 amps of output current. With a typical power per speaker of 10 watts each speaker will consume on the order of 400mA, which means that 12 speakers would require 4,800mA of current. Installed systems that require more output power per speaker simply require that the number of speakers per output A, B and C be reduced so as not to exceed the maximum of 7 amps available.
Speaker Installation The CS650 is designed to be used with the supplied tile bridge and backcan. CAUTION: Be certain that there are no electrical wires, water pipes or heating ducts in the planned installation area before you start drilling or cutting into the ceiling. The CS650 is designed to be installed in the ceiling between the studs or if mounting the CS650 in a drop ceiling the supplied tile bridge and backcan must be used. The CS650 requires a cutout hole of 7 1/8 inches for proper clearance.
Insert the CS650 into the ceiling tile hole and through the tile bridge opening. Begin to tighten the installation screws. As you start to turn each screw the Angle Lug Clamps (A) will rotate outward to engage the tile bridge and ceiling material (C). CAUTION: Do Not Over Tighten the Clamps. Too much torque may snap off the lug, causing the speaker to not seat securely. A snug fit is all that is necessary to assure proper performance.
HDDS CS650 SPECIFICATIONS POWER CONSUMPTION: 400 mA typical 1.
WARRANTY AND SERVICE The unit, parts and workmanship are fully guaranteed to be free of defects under normal use and service for a period of 3 years from the date of purchase. Any damage resulting from the misuse or the failure to follow the precautions and instructions will void the warranty. In the event that the unit needs to be repaired, please return the unit to ISP Technologies directly.
