4-In. Oscillating Wall-Mount Fan Owner’s Manual WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury.
Thank you very much for choosing an Ironton™ product! For future reference, please complete the owner’s record below: Serial Number/Lot Date Code: ________________________________ Purchase Date: ____________________________________________ Save the receipt, warranty, and this manual. It is important that you read the entire manual to become familiar with this product before you begin using it. This fan is designed for certain applications only.
Table of Contents Intended Use .......................................................................................................................................... 4 Packaging Contents .............................................................................................................................. 4 Technical Specification ........................................................................................................................ 4 Important Safety Information ................
Intended Use The Ironton 14 Inch Oscillating Wall-Mount Fan can be used for cooling or to circulate air indoors or in a garage setting. When in operation, the fan has to be mounted to a wall. Packaging Contents Main body (1) Front grill (1) Propeller (1) Rear grill (1) Technical Specification Property Motor Max Current Consumption Max Working Power Max Velocity Max. Air Flow Specification 120 Volt AC; 60Hz 0.
Cluttered, wet, or dark work areas can result in injury. Using the product in confined work areas may put you dangerously close to cutting tools and rotating parts. Do not use the product where there is a risk of causing a fire or an explosion; e.g., in the presence of flammable liquids, gases, or dust. The product can create sparks, which may ignite the flammable liquids, gases, or dust. Do not allow the product to come into contact with an electrical source.
Store the product when it is not in use. Store it in a dry, secure place out of the reach of children. Inspect the tool for good working condition prior to storage and before re-use. Use only accessories that are recommended by the manufacturer for use with your product. Accessories that may be suitable for one product may create a risk of injury when used with another tool. Never use an accessory that has a lower operating speed or operating pressure than the tool itself.
Grounding ⚠WARNING This fan must be grounded while in use to protect the operator from electrical shock. This fan is equipped with an electrical cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching receptacle that is properly installed and grounded in accordance with ALL local codes and ordinances. DO NOT MODIFY THE PROVIDED PLUG. If it will not fit the receptacle. Have the proper receptacle installed by a qualified electrician.
As the distance from the supply outlet increases, you must use a heavier gauge extension cord. Using extension cords with inadequately sized wire causes a serious drop in voltage, resulting in loss of power and possible tool damage. The smaller the gauge number of the wire, the greater the capacity of the cord. For example, a 14-gauge cord can carry a higher current than a 16-gauge cord.
2. Propeller Assembly 2-1. Remove the nut from the motor shaft (Fig.2). 2-2. Slide the propeller onto the motor shaft by aligning its slot with the pin in the shaft (Fig.2). 2-3. Secure the propeller with the nut (Fig.2).
3. Front Grill Assembly 3-1. Remove the screw and nut in the bottom of the front grill (Fig.3). 3-2. Place the front grill against the rear grill with its top buckle encases the rim of the rear grill, and then turn all other buckles so they are encasing the rim also (Fig.3). 3-3. Tighten the two grills with a screw and nut again (Fig.3). I. ATTACH THE FAN TO THE WALL ⚠WARNING Be sure the surface being used is strong enough to hold the weight of the fan.
2. On each horizontal line, drill two holes 4.6 cm apart from the center line with a diameter as that of the wall plugs provided (Fig.5). 3. Insert four wall plugs into the holes (Fig.6). 4. Drive the two provided tapping screws (0.5 cm in diameter and 5 cm length) into two upper wall plugs, leaving a gap of 0.5 cm between the screw head and wall (Fig. 6).
5. Hang unit on the wall. Align its two key holes at the two screws on the wall (Fig.7). 6. Drive the two provided tapping screws (0.5 cm in diameter and 5 cm length) through the lower two holes of the base into the wall plug and secure the unit firmly against the wall. 7. Tighten the two upper screws through the base top hole (Fig.7). The unit is now ready for use. Operating Instructions ⚠WARNING Electric shock hazard. Do not expose the unit or the plug to water or rain.
Do not operate in the presence of explosive and/or flammable fumes. Do not plug/unplug the fan into/from the electrical outlet while wet or standing in a wet or damp area. Never operate the fan without the guard in place. For indoor use only. Do not use outdoors. Do not place the fan in or near a window. Rain may create an electrical hazard. Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for repair before resuming operation.
• • • • and maintenance. Have necessary repairs made by qualified service personnel. Always disconnect the cord from the electrical outlet before cleaning your fan. Light accumulated dust may be removed by using a soft cloth to wipe away the dust at the back grill of the fan. Wipe the exterior surfaces of the fan occasionally with a damp cloth (not dripping wet) and dry thoroughly with a soft dry cloth before operating the fan.
Parts Diagram Parts List Part Number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 Part Description Screw Front Grill Screw Propeller Flange Screw Rear Grill Screw Front Housing Motor Screw Oscillation Knob Rear Housing Screw Link Sleeve Plastic Bracket Irregular Sleeve Steel Bracket Screw Nut Lock Knob Bolt Curve Tube Base Cover Page 15 of 18 Quantity 1 1 3 1 1 1 1 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
Part Number 26 27 28 29 30 31 Part Description Power Cord Switch Brace Bar Base Screw Quantity 1 1 1 1 1 1 Replacement Parts For replacement parts and technical questions, please call Customer Service at 1-800-222-5381. Not all product components are available for replacement. The illustrations provided are a convenient reference to the location and position of parts in the assembly sequence.
Limited Warranty Northern Tool and Equipment Company, Inc. ("We'' or ''Us'') warrants to the original purchaser only (''You'' or ''Your'') that the Ironton product purchased will be free from material defects in both materials and workmanship, normal wear and tear excepted, for a period of one year from date of purchase. The foregoing warranty is valid only if the installation and use of the product is strictly in accordance with product instructions.
Distributed by: Northern Tool & Equipment Company, Inc. Burnsville, Minnesota 55306 www.northerntool.