Installation Instructions

OVERVIEW
www.irtec.com
This product may be covered by one or more U.S. patents or patent applications.
Please visit www.irtec.com for more information.
Lead the wires and strip the insulation with proper length
of conductor for connecting.
Connect the wires to the device according to the wiring
diagram shown.
Carefully set the wires and mount the device into the wall
box with screws provided.
INSTALLATION
1.
2.
3.
Indoor dry location use only
Utilisation a L'interieur Uniquement
AVERTISSEMENT & PRUDENCE
WARNING & CAUTION
Risk of Electrical Shock – Turn off the power at circuit breaker
before installing or servicing.
This device should be installed by a qualified electrician in
accordance with electrical codes and regulations.
Install the device at least 1 ft. away from any occupant.
Risque de choc électrique - Débranchez l'alimentation avant
l'entretien.
Installer et utiliser ce dispositif conformément aux codes et
règlements électriques.
Line Voltage 4-Channel OS-NET Button
ON-PBD-708 series
INSTALLATION INSTRUCTIONS
WIRING DIAGRAM
UP
P/N: 058-70502-001 Printed in Taiwan
DIMENSIONS
PRELIMINARY
3.81”
3.28”
4.13”
2.75”
1.22”
2.73”
1.77”
4.47”
The ON-PBD-708 is a 4-channel wireless button switch
and dimmer for OS-NET wireless lighting control
solution. This line voltage powered device can be
mounted into a standard NEMA wall box to provide
wireless manual on/off and dimming control to comply
with the requirements from the latest energy codes.
The ON-PBD-708 can be easily connected with an
OS-NET wireless mesh network formed by a number
of OS-NET devices by a 2-way handheld remote
programmer (SRP-281). Total 4 channel buttons can
be individually configured to control 1 to 4 lighting
groups as required. A short press at RIGHT ( ) part
of the button will turn ON, and LEFT ( ) will turn OFF
the lighting groups assigned to the channel. Press and
hold at RIGHT ( ) part of the button to ramp up, and
LEFT ( ) to fade down the lighting output of the
group(s) assigned.
With this wireless control device, you can effortlessly
achieve an energy-efficient, code-compliant smart
lighting control through a state-of-the-art wireless
sensor mesh network with manual control capability.
Line
Line
Black
GND Screw (Green)
White
Neutral
Ground
Neutral
NOTE: This device requires neutral wire connection. For the
wall box without neutral, the wire of “switched line” may be
lead to connect with the “neutral” of lighting power instead.
Consult with qualified electrician for code compliant.
NOTE: Do NOT mount
the button upside down.
OFF
(Fade down)
ON
(Ramp UP)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna
or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment.
This equipment should be installed and operated with greater than 20cm between the
radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour
un environnement non contrôlé.
Cet équipement doit être installé et utilisé à plus de 20cm entre le radiateur et votre corps.
Federal Communication Commission Interference
Statement
FCC ID: NRIWS770800
Industry Canada statement:
IC: 22993-708WS7WP401
This device complies with ISED’s licence-exempt RSSs. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et
(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage
susceptible de provoquer un fonctionnement indésirable.