Exhibit 8: User Manual High Performance UHF fixed reader EXHIBIT 8 - UHF RFID READER USER MANUAL 109.
UHF High performance RFID Reader User Manual Version 1.09 August 2008 FCC ID: VHY3271-1 FCC ID: VHY3271-2 FCC ID: VHY3271-3 EXHIBIT 8 - UHF RFID READER USER MANUAL 109.
IMPORTANT Please read instructions before operating this devise. Warranty is void if you open or tamper with this device. Explosive atmospheres User shall switch off this unit and obey all safety requirements in these areas. This unit may only be operated if the area is declared safe by a safety official.
Table of Contents Figures ............................................................................................................................................................. 5 Tables............................................................................................................................................................... 5 History ......................................................................................................................................................
FIGURES Figure 1 Supplied goods and accessories.......................................................................................7 Figure 2 RS 232 (Default) and Mains Power Connection ...............................................................8 Figure 3 RS 232 (Default) and DC 12V Power Connection ............................................................8 Figure 4 RS 232 to RS 485 Converter connection (optional) ..........................................................
GLOSSARY dB dBd dBi dBil EIRP ERP EVI I and Q RFID RFU CW Decibels Antenna gain in dB relative to dipole antenna Antenna gain in dB relative to isotropic antenna Antenna gain in dB relative to linearly polarized isotropic antenna Effective Isotropic Radiated Power (measured in dBi or dBil) Effective Radiated Power (referred to a dipole) (measured in dBd) Electronic Vehicle Identification Quadrature RF signals (90 deg out of phase) Radio Frequency Identification Radio Frequency Unit Continuous Wave EXHIBIT
1. Supplied goods and accessories TOP: Data communication cable (shipped with 6m cord) BOTTOM: Power cable (shipped with 6m cord) Please consult your local dealer for different cable assemblies Reader front view Rear view of Reader Note the included pole mounting brackets. User Manual NOTE: Please refer to the technical specification or contact your local dealer on the different reader User Manual and Demo software are configurations available. available on WWW.IPICO.
2. Cable Connections To PC 9p Female D type Pin 1 Nc 2 Receive Data 3 Transmit Data 4 Nc 5 Signal Ground 6 Nc 7 RTS 8 CTS 9 Nc P1 DATA (12P Female) Pin A Nc B Receive Data C Transmit Data D Nc E Signal Ground F CTS G RTS H Nc J Nc K Nc L Nc M Nc P2 POWER (3P Female) Pin 1 Live 2 Neutral 3 Earth Brown Connect to AC power source (AC 90-264V ~ 1.
To PC com port via 25P Female SCREW TERMINALS Pin 4 Receive + 3 Receive 2 Transmit 1 Transmit + Green Yellow Blue Red Isolated Converter powered by an external PSU P1 DATA (12P Female) Pin A Transmit + B Transmit C Receive D Receive + E Nc F Nc G Nc H Nc J Nc K Nc L Nc M Nc Refer to Figure 2 or 3 for Power connection Figure 4 RS 232 to RS 485 Converter connection (optional) Note: The RS 232 to RS485 converter is used to increase the distance between the reader and the host controller (typically a PC)
RJ45 (Wiring according T568A) 1 Green/White P1 DATA (12P Female) Transmit + Pin A Transmit + Transmit - 2 Green Transmit - B 3 Orange/White Receive + C Receive + 4 Blue NC D Receive - 5 Blue/Wht NC E Nc 6 Orange Receive - F Nc 7 Brown/wht NC G Nc 8 Brown NC H Nc J Nc K Nc L Nc M Nc Refer to Figure 2 or 3 for Power connection Figure 5 Ethernet connection (optional) EXHIBIT 8 - UHF RFID READER USER MANUAL 109.
3. Front panel Indicator Figure 6 Reader status indicator A tri-colour LED will indicate the following reader status to the operator · Steady RED light indicates Power ON but no processor/communication activity. · Slow GREEN Flash at 1/6Hz indicates Internal processor working. · Fast GREEN Flash at 1/2Hz indicates communication activity between reader and controller/PC. · Random GREEN fast Flash indicates that a valid Tag ID is decoded. EXHIBIT 8 - UHF RFID READER USER MANUAL 109.
4. Operations overview The IPICO reader is designed as a read/write (RW) reader. The reader modulates READ commands to the tags in order to interrogate the tag. Depending on the application new DATA can be updated on the tag using a modulated WRITE command. Read commands will typically be 5ms in duration with a response from the tag in 300us for 64bits. A WRITE command will typically be longer and will average around 35ms.
6. Installation and Set-up Note: The following set-up is for demonstration purpose only. Installation and applications will be site dependant. 1. Install ShowTags on the controlling PC running on Windowsä 95,98 NT or 2000. It consists of a single .EXE file, which can be copied from the supplied 3.5” disk to any directory on the controlling PC and run from that directory. From time to time updates are available on the Web at http://www.IPICO.com 2. Start ShowTags. Check the serial port settings.
6.1 Quick start (Ethernet communication) Connect the Ethernet cable to J20 on the Registration Reader and proceed as follows: Note: The default factory settings are IP = 192.168.1.31 port 6543 In case the user wants to change IP/port settings of the reader, edit the file in Appendix 1 and upload the file to the reader by doing the following procedure: a. Open the Moxa SDK tool. (Download from support at www.IPICO.com) b. Do a broadcast search and select the reader that is found c.
d. Click on OK and wait for the upload to finish. e. Default values in the .txt file are uploaded. Click on OK, accept the changes made and Exit the configuration tool. EXHIBIT 8 - UHF RFID READER USER MANUAL 109.
8. Application notes 1. Some of the IPICO tag antenna formats are dipoles. Like dipoles, they have nulls end-on. 2. Tags should always be orientated in a plane orthogonal to the direction to the reader. 3. Reading speed depends on the tag version used. Please consult IPICO’s support team or your local dealer regarding these specifications. 4. Up to 30 tags can be read per second.
Figure 9 EVI Reader Installation: Side read scenario Figure 10 EVI Reader Installation: Overhead read scenario Note: Typical angle is also a function of height above ground and is site dependant. Surrounding structures may cause unwanted reflections or extended read capabilities. The installer needs to test and re-adjust for Overhead: 30° - 40° Roadside: 40° - 90° best performance. Figure 11 EVI Reader Installation angle EXHIBIT 8 - UHF RFID READER USER MANUAL 109.
R freq 1 R freq 2 R freq 1 R freq 2 Figure 12 Example of multiple EVI reader installation for Free flow tolling/spotting Note: R freq n = Reader frequency allocations (these are country and site dependable) Fixed Frequency Free flow overhead EVI readers with Std R freq 1 - R freq 2 ³ 6 MHz decoders Free flow overhead EVI readers with DSP R freq 1 - R freq 2 ³ 1 MHz decoders Non Free flow I.
Figure 13 Examples of sunshades for harsh environments Figure 14 Typical ENP tag location and orientation EXHIBIT 8 - UHF RFID READER USER MANUAL 109.
9. Troubleshoot Visual indicator guide · Steady RED light indicates Power ON but no processor/communication activity. · Slow GREEN Flash at 1/6Hz indicates Internal processor working. · Fast GREEN Flash at 1/2Hz indicates communication activity between PC and reader. The fast heartbeat will only start, once a command has been received by the reader. · A random GREEN fast Flash indicates a valid Tag ID.
11. Technical specification Mains input type: 90 - 264 VAC @ ~1.4A, 50/60 Hz Power supply requirement Low voltage input type: 11.7 – 12.3 VDC @ 2.5 A max (typ 600mA for500mW reader) (12V device is only reversed polarity protected up to 20Vmax.
12. Support Ordering information Description Model UHF High Performance reader IP 3271 Frequency Band US (-1, -2 or -3) Specify other Frequency Power Supply 12VDC Mains 90-264VAC 50/60Hz Communication interface RS 232 Ethernet Wiegand RS 485 Antenna type EVI (Std 4WEIRP) HP (Std 500mW ERP or 4WEIRP) NOTE: Please consult your local dealer for more information regarding the accessories, system design, frequency and RF power settings. 13. Technical Assistance IPICO online http://www.IPICO.
Group IPICO INC Ontario, Canada tel: +1 905 631 6310 fax: +1 905 631 6614 info.can@IPICO.com www.IPICO.com Operations South Africa Pretoria tel: +27 12 345 9520 fax: +27 12 345 5834 info.sa@IPICO.com Australasia Clontarf, Queensland tel:+61 7 3889 5799 fax: +61 7 3889 5980 info.aus@IPICO.com EXHIBIT 8 - UHF RFID READER USER MANUAL 109.DOC North Asia Shanghai, China tel: +86 21 5080 0345 fax: +86 21 5027 8271 info.cn@IPICO.com China Beijing, China tel: +86 10 8280 0541 fax: +86 21 8280 0546 info.
14. Appendix 1: MOXA Ethernet converter Configuration file This is the content of the Moxa_config_file.
15. Appendix 2: Typical EVI setup: Overhead and Road side EXHIBIT 8 - UHF RFID READER USER MANUAL 109.
EXHIBIT 8 - UHF RFID READER USER MANUAL 109.
10°-30° EXHIBIT 8 - UHF RFID READER USER MANUAL 109.