nanoLTE S60 AP Hardware Installation NANO_INST_43315 200_0.
Notices This document is provided to you by or on behalf of ip.access Ltd ("ip.access"). © ip.access Limited 2017. The documentation and any software described herein and/or provided to you in conjunction with this documentation contain proprietary and confidential information of ip.access and may only be used subject to a license agreement containing restrictions on use and disclosure. They are also protected by copyright, patent rights and other intellectual and industrial property laws.
Revision History Version Change Summary Date Author 200_0.1 First draft 17 Oct 2016 AM4 200_0.2 Updates from review feedback 21 Oct 2016 AM4 200_0.3 Minor updates from review feedback 21 Oct 2016 AM4 200_0.4 Add RF exposure statement to regulatory statements 03 Aug 2017 AM4 200_0.
Table of Contents 1 Introduction............................................................................................ 1 1.1 Overview ............................................................................................................ 1 1.2 Warnings and Regulatory Information ............................................................... 1 1.3 Related Information............................................................................................ 1 1.
.3.1 Output Specification ........................................................................................... 21 nanoLTE S60 AP Hardware Installation NANO_INST_43315 v200_0.5 for N4G_2.0 © ip.
1 Introduction The ip.access nanoLTE S60 AP is an indoor Access Point for SOHO and enterprise small cell applications. This manual provides all the necessary information required for hardware installation of a nanoLTE S60 AP. 1.1 Overview This manual is organised as follows: • This introduction • An overview of nanoLTE S60 AP installation, including site requirements • nanoLTE S60 AP hardware installation • Troubleshooting • Regulatory warnings and safety information 1.
2 Installation Overview and Requirements 2.1 Installation Tasks The tasks that must be completed to install a nanoLTE S60 AP and make it ready to provide service are: • Pre-Provisioning • Site installation These tasks can be completed in any order. In most cases, however, the most practical approach is to pre-provision an S60 AP before site installation. 2.1.1 Pre-Provisioning For information about nanoLTE AP pre-provisioning, see the nanoLTE AP Configuration manual [INST_43370].
2.3 nanoLTE S60 AP Site Requirements The basic requirements are: • A mounting location for the S60 AP. • Power supplied via the supplied mains adaptor unit, which requires a suitable mains power supply point near the AP that is within reach of the adaptor’s cabling. • An Ethernet cable connection to the Internet, or equivalent backhaul network 2.3.
2.3.3 Port Usage This information is provided in case it is needed for configuring local on-premises equipment, especially any hardware firewalls between the AP and the rest of the backhaul network. All connections are outgoing. That is, they are initiated from the AP. Port usage has some dependency on whether or not the AP is using IPsec.
If the NOS is configured for HTTPS access to the Certificate Validation Service for CRL Mirror server functionality, the AP will also need to use this port outside of the IPsec tunnel: Protocol Destination Port Use tcp 443 HTTPS for CRL download from the NOS Port Usage Without IPsec Without IPsec, the following ports are used: Protocol Destination Port Use sctp 36412 SCTP connection udp 2152 PS GTP from AP udp 2152 PS GTP to AP tcp 8080 or 7547 TR-069 to the NOS (the NOS listens for TR
2.3.4 nanoLTE S60 AP Power Requirements Maximum expected power consumption: • 15 Watts (Rated +12V on the DC input) The S60 AP only uses power from a suitable DC source (+12V, 1.67A rated centre positive 2.1mm jack). Use the supplied mains adaptor only. PSU The following 12V PSU, rated up to 20W, is included in the box with the S60 AP: There must be a suitable mains power supply point for plugging in the power adapter. The lead on the PSU is 1.5m long, hence the power supply point must be within 1.
2.3.5 S60 AP Physical Requirements An S60 AP is installed by mounting it on a wall or partition on screws or by sitting it on the supplied stand. Pay attention to ensure that air can circulate freely around the unit. The unit must be vertical. It is recommended to install the AP with its front surface facing the area requiring cellular coverage, unobstructed by walls or partitions that may cause significant RF attenuation.
3 nanoLTE S60 AP Hardware Installation 3.1 Unpack the S60 AP 1) Unpack the AP and its accessories. Box contents may vary, but typically the box should contain the following: • S60 AP unit with wall bracket attached • Tabletop stand • Mains power supply unit with plug adaptors • Ethernet cable (approx 2m) 2) Check that the serial number on the AP unit matches the label on the box. 3) Check that the items have not been damaged in transit.
3.3 Mount the nanoLTE S60 AP on its Stand 1) Fit the S60 AP onto its stand. It should click into place when the unit is oriented correctly on the stand. 2) Position the S60 AP in a suitable location, within reach of a power supply point and an Ethernet connection. When it is on its stand, the AP must be on a stable flat surface. 3) Plug in the required cables. Plug an Ethernet cable from a switch/gateway into LAN and the included power supply into the +12V DC input: Route the cables safely.
3.4 Note: Mount the S60 AP on a Wall The S60 AP should be installed in a position so that it is at least 2m away from the area where handsets are normally used. The S60 AP must be mounted vertically to ensure air circulation around the unit. The location of each S60 AP should be shown on an installation floor plan produced at the network planning stage. For example, it must take into account that all APs must be at least 2m from any mobile equipment.
4 Troubleshooting This section covers the following topics that may be useful for troubleshooting a nanoLTE S60 AP during installation: • 4.1 nanoLTE S60 AP Does Not Power Up • 4.2 nanoLTE S60 AP LEDs • 4.3 Factory Reset For more information on AP troubleshooting, see [TRB_43005]. 4.1 nanoLTE S60 AP Does Not Power Up Check the following: • Verify the correct power supply is in use and that mains power is available. • Ensure that PoE or PoE+ is not being used to attempt to power the AP.
LED Colour Description Off The AP does not yet have an IP address. This should change shortly after the AP is switched on. Red If this LED has previously been Green, Red means that there is an error, such as the AP losing its IPsec connection with the security gateway. Green Flashing Green indicates the AP is acquiring NTP or connecting to its IPsec Security Gateway. Steady Green indicates the AP is connected to its serving IPsec security gateway.
4.3 Factory Reset Only use a factory reset when there is no other way to repair the AP connection to either the IPsec SecGW and/or the NOS Server. First ensure that all other possibilities have been explored and eliminated. A factory reset will clear the configuration supplied to the AP by the NOS (or TR-069 ACS if the NOS is not used).
Select in Navigation Parameter Pane Notes FAPService.{i}.FAPCon X_000295_DefaultSecGWSer The serving IPsec gateway address. trol.UMTS.Gateway ver If all these Default values are null, this means that the AP has never connected to the NOS, so it has been unable to inform the NOS with these values. In this case, check the AP’s ability to connect to the Field Redirector and the IPsec SecGW.
To resolve any incorrect provisioned values, correct them in the NOS then perform a factory reset. The AP will reconnect to the NOS using the default factory configuration and then obtain the updated configuration. 4.3.1 S60 Factory Reset 1) Use a thin rod to press and hold the reset button, which is accessed through a small hole under the Ethernet port. 2) Keep the reset button pressed until the Service LED changes from blinking fast (50ms on, 50ms off) to blinking slowly (50ms on, 200ms off).
5 nanoLTE AP and PSU Regulatory Information This chapter provides the customer with safety and regulatory warnings, cautions and information for the ip.access Ltd range of products. • 5.1 Warnings and Cautions • 5.2 Regulatory Statements for nanoLTE S60 AP • 5.3 Regulatory Statements for PSAA20R-120L6 PSU 5.1 Warnings and Cautions Electrical Safety CAUTION The nanoLTE AP is intended for dry indoor applications only. If evidence of condensation is present do not apply power to the nanoLTE AP.
CAUTION When disconnecting the power supply from the mains, pull the plug. Pulling the cable may result in damage to the cable. Interference with Electronic Devices CAUTION If using a pacemaker, ensure you are using the device in accordance with its safety requirements with respect to RF devices. Consult your doctor if you have questions about RF signals and your pacemaker. CAUTION If using a hearing aid, RF devices may cause interference.
5.2 Regulatory Statements for nanoLTE S60 AP 5.2.1 US FCC Compliance • FCC CFR47 Parts 15B, 24 Note: Changes or modifications not expressly approved by the party responsible for compliance may void the user's authority to operate this equipment. Model LTE Band FCC ID nanoLTE S60 435R 2 QGGIPA435R WARNING This is a class B product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.
5.2.2 EU Regulatory Compliance The nanoLTE AP model 435S (Band 3) conforms to the following regulatory standards: Health (Art 3.1(a)): EN50385: 2002 Safety (Art 3.1(a)): EN 62368-1:2014 EMC (Art 3.1(b)): Draft EN 301 489-1 V2.1.0, Draft EN 301 489-50 V2.1.0 Spectrum (Art 3.2): EN 301 908-14 V11.1.1 This product is intended for use in all Member States of the European Union. "Hereby, ip.
5.3 Regulatory Statements for PSAA20R-120L6 PSU Safety Approvals UL/cUL 60950-1 CB CE SAA+C-TICK+MEPS Mechanical Characteristics L x W x H: 71.7mm x 50.0mm x 39.1mm (2.82" x 1.97" x 1.54") Weight:: 180.8g (6.
5.3.1 Output Specification Model DC Output PSAA20R-120L6 12V / 20W Load Min Max 0A 1.67A nanoLTE S60 AP Hardware Installation NANO_INST_43315 v200_0.5 for N4G_2.0 © ip.
