User's Manual

ManualsBrandsIon Digital ManualsElectronicsSecurity/Remote Control Transmitter

Table Of Contents

FCC ID: QN3WD01 Installation Guide

ION Digital LLP 11/04/02

1 of 6

ION Digital LLP Ph# 1-800-407-4389

P.O. Box 3969 Blaine Washington Fax# 1-800-407-4465

USA 98231 www.ion-digital.com

Embedded Window Frame Security Sensor

Installation Instructions

The Embedded Window Frame Sensor/Transmitter

detects when a window is closed or opened, and

transmits a wireless security message to the System Control Panel. This is accomplished through the use

of a sensor unit (which contains the wireless transmitter and battery), and magnet unit. When the two are

separated, by opening the window, the sensor transmits an OPEN signal to the System Control Panel.

When the window is shut, the magnet is again within the sensor's range, and a CLOSE signal is sent.

Fig 1: Sensor and Magnet

The sensor sends supervisory signals to the panel every 64 minutes (approximately). The sensor is

and provide long battery life. The entire package needs to be removed from the window frame for the

battery to be replaced.

Required Tools for Installation

 Electric Drill

 SDI Custom Frame Drill Bit

 Pencil or chalk

 Installation Sheet for documenting sensor locations

Guidelines

The following guidelines will help ensure that installations are safe and efficient.

 A sensor can be mounted on any side of the window frame (top, side, or bottom), such that the opening

of the window moves the magnet away from the sensor.

 Always try to mount the hardware such that the magnet, not the sensor, is in the moving window panel.

The sensor can be installed in the moving window panel, but should be avoided.

 Do not install the sensor in the frame until after the Electronic Serial Number (ESN) has been entered

into the panel, and the wireless sensor confirmed within range. The 6 digit (including HEX values)

ESN is labeled on the device.

 Sensor’s should be kept as close to the panel or repeater as possible. Try to chose locations where the

separation is within 100 ft.

 Avoid mounting the sensor in a location where it will be exposed to moisture.

 Avoid mounting a sensor where temperatures are excessively hot or cold.

 This device cannot be mounted in a metal frame, as the frame will block the antenna (there is an

external version of this device that will fit on the exterior of an aluminum frame).

WARNING:

Some installations may have electrical wiring running through the door or window

frames. Use caution to avoid electrical shocks

Magnet

Sensor & Antenna

Summary of content (6 pages)

PAGE 1
FCC ID: QN3WD01 ION Digital LLP Installation Guide 11/04/02 Embedded Window Frame Security Sensor Installation Instructions The Embedded Window Frame Sensor/Transmitter detects when a window is closed or opened, and transmits a wireless security message to the System Control Panel. This is accomplished through the use of a sensor unit (which contains the wireless transmitter and battery), and magnet unit.
PAGE 2
FCC ID: QN3WD01 ION Digital LLP Installation Guide 11/04/02 Preparation 1. Determine a suitable location for the sensor and the magnet. These units are meant to be mounted inside the frame of the window. As such do not drill a mounting hole unless: • You are a qualified installer • There is sufficient room for the devices in the frame and window (Not all windows may have the necessary clearance).
PAGE 3
FCC ID: QN3WD01 ION Digital LLP Installation Guide 11/04/02 Fig 3: Incorrect Orientation of Magnet and Sensor Direction of Window Movement, magnet moves over and past sensor. 3 of 6 ION Digital LLP P.O. Box 3969 Blaine Washington USA 98231 Ph# 1-800-407-4389 Fax# 1-800-407-4465 www.ion-digital.
PAGE 4
FCC ID: QN3WD01 ION Digital LLP Installation Guide 11/04/02 Entering and Testing Sensors The sensors need to be entered into the control panel memory. This is done by entering the 6 digit (including HEX values) ESN into the panel to record it. Refer to your panel installation manual for complete details. To test the sensor, you need to enter the panel’s wireless test mode. Then: 1. 2. 3. Trip the sensor. This is done by moving the magnet in, and out of position.
PAGE 5
FCC ID: QN3WD01 ION Digital LLP Installation Guide 11/04/02 Installation in Window Frame 1. 2. 3. 4. Using the dealer provided window frame bit supplied with your dealer kit, drill a ¾” hole in the frame for the sensor, and one in the window panel for the magnet. Both the sensor and the magnet have ribs on the outside that will provide a bite fit into the frame. First insert the wire into the inside of the frame, through the hole just drilled.
PAGE 6
FCC ID: QN3WD01 ION Digital LLP Installation Guide 11/04/02 FCC Notice THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERNCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Changes or modifications not expressly approved by ION Digital LLP can void the user’s authority to operate the equipment. 6 of 6 ION Digital LLP P.O.