User's Manual

ManualsBrandsIon Digital ManualsElectronicsSECURITY WIRELESS WINDOW SENSOR

Sash Magnet

Press the iON 5800 MICRA transmitter's corresponding

magnet into the cavity now drilled into the sash,

making sure to position the iON icons to point in the

same direction.

NOTE: This point is essential to

the systems proper operation.

Measure 3" down from the inside top corner of the

mainframe and mark the center point for the hole the

iON 5800 MICRA transmitter will be inserted into.

Place a corresponding mark also on the sash insert that

will be used in this position.

Measure & Drill

Place and Set

NOTE: It is essential to the systems operation

that the positioning of the iON icon on the

transmitter point in the same direction as its

corresponding sash magnet.

Insert the iON 5800 MICRA's antenna into

the extrusion hollow then press the

transmitter body into the cored opening.

Using a 3/4" Forstner Drill Bit,

drill into the vinyl window

mainframe.

Sash Magnet

Placement

NOTE: The vinyl extrusion should be pre-qualified by a

iON Security rep. to ensure the frame will accommodate

the iON 5800 MICRA transmitter as well as

the

placement

of its

corresponding magnet

Side mount

transmitter

on Vinyl

Sliders

Sill mount transmitter

on Hung Windows

Horizonta

Slidi

ng Sash

Vertical Sliding

Sash

Using a 3/4" Forstner Drill Bit, drill into the

window sash to a depth of 1/3" only.

0.5"

< extrusion hollow >

0.33"

core depth

outer

wall of

window

frame

inner wall

of window

frame

3/4" Forstner

drill bit

iON 5800 MICRA

Recessed Transmitter

Installation Instructions

For use with QED control panels ONLY!

GENERAL INFORMATION

The iON 5800 MICRA recessed transmitter is a reed switch magnetic contact

transmitter that provides concealed protection for a window. It is intended for

use only with alarm systems that support QED 5800 series devices. The

transmitter is powered by a long-life lithium battery that is easily replaceable

when a low battery is indicated by the control.

Programming the ID Number

Each iON 5800 MICRA has its own unique identification code (serial

number) permanently assigned during manufacturing.

The control unit is required to "enroll" the transmitter's ID during installation

of the alarm system. The iON 5800 MICRA response should be enrolled as "RF"

(i.e. Supervised RF) Type (mandatory for all UL installations).

Refer to the QED control unit's installation instructions for further details.

PRELIMINARY CONSlDERATlONS

Read all of this and the next section before installing the unit.

1.Select a location for the transmitter on the frame of the window.

 Do not use on metal frame doors or windows.

 iON 5800 MICRA TRANSMITTER

 The iON 5800 MICRA transmitter will require a 3/4" diameter hole (using 

 a 3/4" Forstner bit) drilled into the edge of the window frame no more 

 than 1/3" deep. Its accompanying magnet will need a 3/4" diameter 

 hole drilled in the side of the window sash, no more than 1/3" deep. 

 BEFORE DRlLLlNG ANY HOLES, SEE ITEM 2 BELOW AND MOUNTlNG 

 SECTION ON THE NEXT PAGE.

 FOR VINYL SLIDING WINDOWS the preferred direction of mounting is vertical. 

 FOR HUNG WINDOWS the iON 5800 MICRA must be mounted horizontally 

 in the window sill with the accompanying magnet mounted in the lower 

 window sash. (see Step 1 - Measure & Drill in Figure 1)

2.Before drilling any holes, tape the transmitter and magnet in their 

 approximate locations (with battery installed and unit together as 

 described under BATTERY INSTALLATION / REPLACEMENT (see page back) 

 and conduct Go/No Go tests (see QED control's instructions) to verify 

 adequate signal strength. Reorient or relocate the transmitter if necessary.

 Make sure that no more than a 1/2" gap will be present between the faces 

 of the transmitter and magnet cases when they are installed and set. Also 

 make sure the 'iON' graphic on the transmitter and magnet are aligned with 

 each other as per Step 3 - Sash Magnet Placement in Figure 1.

 When installed, an alarm signal must be obtained before a clear space of 2" 

 is reached as the window is opened.

Under no circumstances should the outer wall of the

window frame be penetrated by the Forstner bit.

Figure 1

WARNING: under no circumstances

should the outer wall of the window

frame be penetrated by the Forstner bit.

Summary of content (2 pages)

PAGE 1
iON 5800 MICRA Recessed Transmitter Under no circumstances should the outer wall of the window frame be penetrated by the Forstner bit. Using a 3/4" Forstner Drill Bit, drill into the vinyl window mainframe. Figure 1 Installation Instructions 1 Measure & Drill Side mount transmitter on Vinyl Sliders For use with QED control panels ONLY! GENERAL INFORMATION The iON 5800 MICRA recessed transmitter is a reed switch magnetic contact transmitter that provides concealed protection for a window.
PAGE 2
Before drilling any holes, make sure that successful iON 5800 MICRA Recessed Transmitter BATTERY CAUTION: Risk of fire, explosion and burns. Go/No Go transmission reception tests have been conducted as called for in the Do not recharge, disassemble, heat above 212"F (100"C) or incinerate. Dispose iON 5800 MICRA transmitter section. of used batteries promptly. Keep away from children. MOUNTING (See Figure 1) 1. Mark the selected location for the transmitter on the frame of the window.