Installation Guide

ManualsBrandsInVue ManualsElectronicsTAB S7 HORIZ S PEN TRAY

DKTZ502/03/04

Tab S7/S7+ Horizontal

S-Pen Non-Alarming

Tray Qty. 1

Assembled Stylus Clip

Qty. 1

Key Fob Tool

Qty. 1

Samsung Tab S6/S7/S7+ S-Pen Tray Recoilers

Installation Guide

Please read the entire guide before beginning the installation and follow all steps as Please read the entire guide before beginning the installation and follow all steps as

described. Please keep this manual for future reference.described. Please keep this manual for future reference.

DKTZ501

Tab S6 Horizontal

S-Pen Non-Alarming

Tray Qty. 1

System

Components:

Outer Sleeve

Qty. 1

Bottom Stylus Clip

Piece

Qty. 1

Top Stylus Clip Piece

Qty. 1

D E F

Retainer

Qty. 2

Place the recoiler in the

desired location and apply

pressure for at least 10

seconds.

Part 1: S-Pen Tray Installation

CAUTION!

24 hours is required for all adhesives to completely cure and reach full adhesive strength.

Please do not use the products immediately after the placement of the adhesive.

Clean the xture with the

alcohol wipe provided.

Let it dry completely.

Peel the liners from the

adhesives on the bottom of

the recoiler.

Part 2: Tether Installation

Optional:

If desired, route the cable

through a hole or slot in the

xture.

Remove the pin cover from

the fob tool.

Insert the pin into the hole

near the tether cable exit.

Pivot the fob tool forward to

remove the retainer.

Note: Be careful not to lose

the clip when removing.

Remove the sleeve and

separate the upper and

lower halves of the stylus clip.

Leave the tether emerging

from the sleeve.

Summary of content (4 pages)

PAGE 1
Samsung Tab S6/S7/S7+ S-Pen Tray Recoilers Installation Guide ! Please read the entire guide before beginning the installation and follow all steps as described. Please keep this manual for future reference. A1 A2 DKTZ501 Tab S6 Horizontal S-Pen Non-Alarming Tray Qty. 1 System Components: C CAUTION! DKTZ502/03/04 Tab S7/S7+ Horizontal S-Pen Non-Alarming Tray Qty. 1 D Assembled Stylus Clip Qty. 1 ! Or B Key Fob Tool Qty. 1 E Outer Sleeve Qty. 1 Bottom Stylus Clip Piece Qty.
PAGE 2
pad satur ated in E 75% LY E ON US OF AL H TERN REAC R EX OF FO OUT REN ES EY KEEP CHILD OM FR AY AW FIRE One TENTS: CON Alcohol Isopropyl as KEEP AND lly a. ica are top g ply untin Ap e mo : NS surfac IO CT anse RE cle DI ed to need 8 Use the provided alcohol wipe to clean the end of the S-Pen. Allow it to dry completely. 9 Align the provided piece of tape to the split line near the butt cap on the S-Pen. Wrap the tape around the S-Pen.
PAGE 3
Part 3: Removal & Recoiler Replacement 1 Unplug the power supply from the outlet. 2a Insert the pin fob tool into the hole next to the cable. 2b Pivot the fob tool back to remove the retainer. 3 Slide the sleeve off the S-Pen clip assembly. 7 Remove the panel. Note: Be careful not to lose the clip when removing. Recoiler Replacement: Use a Philips head screwdriver to remove the screw holding the panel on the bottom of the tray. 4 Slide the sleeve off the S-Pen clip assembly.
PAGE 4
PMN: TAB S7 HORIZ S SPEN TRAY FCC ID: 2AFR8F1754A FCC WARNING STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device complies with Part 18 of the FCC rules.