Quick Start Guide

ManualsBrandsInvenco ManualsElectronicsOutdoor Contactless Card Payment Module (Secure Contactless Controller)

Table Of Contents

Chapter Heading - Table of Contents

SCC Quick Start Guide: P2-400 SCC Setup

DCV-00617 S2 R01

September 2021

S2 Security Level Guide

No restrictions apply: customer facing document

Summary of content (8 pages)

PAGE 1
SCC Quick Start Guide: P2-400 SCC Setup DCV-00617 S2 R01 September 2021 S2 Security Level Guide No restrictions apply: customer facing document
PAGE 2
Release History Version Prepared by Date Change description 0 Shibani Joshi 2021 Aug 17 Created documentSP 1 Michael Doh 2021 Sep 15 Revised wiring connections DCV-00617 S2 R01 1
PAGE 3
Table of Contents Release History...........................................................................................................................1 Introduction ...............................................................................................................................3 1.1 1.2 SCC Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3 Before you begin . . . . . . . . . . . . . . . . . .
PAGE 4
Introduction ©2021 Invenco Group Ltd. All rights reserved. The information in this document is subject to change without notice and should not be construed as a commitment by Invenco Group Ltd. Invenco Group Ltd has taken great effort to verify the accuracy of ©2021 Invenco Group Ltd. All rights reserved. This guide covers how to install and configure a Secure Contactless Controller (SCC) in a G7-100 terminal. The SCC is also known as a G7 Smart NFC Puck. 1.
PAGE 5
Installation 2.1 Installing the SCC The SCC is designed as a drop-in replacement for the existing NFC antenna and LED contactless reader module. To install the SCC: 1. 2. 3. 4. 5. 6. Disconnect the NFC contactless reader and LED cables from the UPC. Remove the contactless reader. Fit the SCC in place of the contactless reader. Remove the USB cable connecting the APC to the SDC. Connect the SCC's USB 'A' cable to the APC. Connect the SCC's USB 'B' cable to the SDC.
PAGE 6
Approvals Invenco develops and maintains its hardware and software products using industry-standard quality processes and is audited by the MasterCard TQM (Terminal Quality Management) scheme. 3.1 The P2-400 SCC approvals: The P2-400 SCC has the following approvals: • CAN/CSA C22.2 No. 62368-1-14 (Safety - Audio/video, information and communication technology equipment) • CSA C22.2 No.
PAGE 7
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
PAGE 8
NEW ZEALAND Level 2, 7-11 Kawana St Northcote Auckland 0627 New Zealand Ph: +64 9 905 560 NORTH AMERICA Building 100, Windward Chase 1235 Old Alpharetta Rd, Suite 130 Alpharetta Georgia 30005, USA Ph: +1 470 253 7568 ASIA Level 3, Wisma Ali Bawal 1 Jalan Tandang 46050 Petaling Jaya Selangor, Malaysia Ph: +60 3 7781 0298 EUROPE 6th Floor, White Building 1 - 4 Cumberland Place Southampton SO15 2NP United Kingdom Ph: +44 23 8022 7645 ©2021, Invenco Group Ltd. All rights reserved.