LUMEN 1000 PSAP & CHARGING TV STREAMER Quick Start Guide 22602 Rev B 1
Table of Contents Lumen 1000 PSAP Parts …………………………….........3 Charging TV Streamer Parts ..…………………………….4 Charging TV Streamer Setup .…………………….…...4-7 Lumen 1000: Assembly and Charging …………….….8 Lumen 1000: Positioning on the Ear ………………....9 Charging TV Streamer: Device Commands .….....10 Lumen 1000: Rocker Switch Functions …………....11 Additional Information .…………………………………...
Lumen 1000 PSAP Parts (Personal Sound Amplification Product) Parts Included a. 2 Lumen 1000 PSAP Devices b. 6 Sound Tubes (3 Left, 3 Right) c.
Charging TV Streamer Parts Charging TV Streamer Power Plug Antenna a Parts Included b a. 1 Charging TV Streamer b. 1 Power Plug c. 1 Mini USB to USB Power LED Indicator (Blue) Cable a. 1 Audio Cable Charging LED Indicator (RED) Charging LED Indicator (Red) (M) Mode Button Audio Cable Mini USB to USB Cable b.
Charging TV Streamer : Set Up Connecting Charging TV Streamer Tip: When outside of the Charging TV Streamer range (16 feet), the Lumen 1000 automatically switches to the PSAP mode. 1. Raise antenna to vertical position and insert Mini USB plug into the back of the Charging TV Streamer. 2. Attach the USB end of the cable to the Power Plug. Antenna USB 3. Insert the Power Plug into an electrical outlet. Mini USB 4. Insert one end of the audio cable into the Charging TV Streamer. 5.
Charging TV Streamer: Set Up – Connect to TV Headphone Jack 1. Locate headphone jack on the front, side or back of your TV. It will be identified by a headphone icon label, similar to the diagram shown. 2. Insert Audio Cable into TV headphone jack Audio Output Jacks 1. Locate audio output jacks on the front, side or back of your TV. They will look similar to the diagram shown. (See your specific products user manual for more information) 2. Insert the red RCA adapter into the red (R) jack.
Charging TV Streamer: Set Up – Connect to TV Computer Headphone Jack 1. Locate headphone jack on the front, side or back of your computer. It will be identified by a headphone icon label, similar to the diagram shown. 2. Insert Audio Cable into the computer headphone jack A/V Receiver Audio Output Jacks 1. Locate audio output jacks on the front, side or back of your A/V Receiver. They will look similar to the diagram shown. (See your specific products user manual for more information) 2.
Lumen 1000: Assembly and Charging Assembling the Lumen 1000 1. Choose left and right Sound Tube 2. Attach Dome Tip to Sound Tube. Choose a small or medium Dome Tip based on your personal comfort. 3. Snap base of Sound Tube assembly to nipple on earpiece. Charging the Lumen 1000 1. Insert body of the Lumen 1000 into the charging slot of the Charging TV Streamer. The Lumen 1000 must be turned off prior to charging. 2. The Sound Tube will remain hanging on the Antenna side.
Lumen 1000: Positioning on the Ear Instructions for wearing 1. Place listening device over ear. 2. Insert Dome Tip into ear canal. 3. Tuck Retention Loop along bottom of ear cavity. 1. 2. 3.
Charging TV Streamer: Device Commands Note: Make sure Lumen 1000 and charging TV Streamer is both ON to hear streaming audio Using your Charging TV Streamer 1. Wear and turn ON Lumen 1000. 2.
Lumen 1000: Rocker Switch Functions Command User Action Audible Prompt Says Turn ON When in OFF mode, Press rocker down until an audible response is heard “Battery” followed by “Low”, “One”, “Two”, “Three”, or “Four” dependent on battery level Turn OFF Press rocker down until an audible response is heard “Off” Briefly press rocker up None. Audible beep when volume reaches maximum range Briefly press rocker down None.
Additional Information The Lumen 1000 battery life is about 4 hours when streaming continuously and 15 hours in PSAP mode. Charging TV Streamer range is approximately 16 feet. The Lumen 1000 automatically switches from PSAP to streaming mode when Charging TV Streamer is turned ON (blue LED on). Turn OFF Charging TV Streamer (blue LED off) during Lumen 1000 charging. Turn OFF the Lumen 1000 before charging. This will ensure the Lumen 1000 receives a full charge.
FCC LABEL REQUIREMENTS This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. (REF only - PER 15.19(a)(3)) Changes or modifications not expressly approved by IntriCon for compliance could void the user’s authority to operate the equipment. (REF only – per 15.