SOLO LTE-M SOLO 4G/3G (SK) USER MANUAL 700050-BS May 2022 Version 1.
INTENTIONALLY BLANK 700050-BS May 2022 Version 1.
TABLE OF CONTENTS INTRODUCTION CUSTOMER SUPPORT ................................................................................................................................. 3 SOLO CERTIFICATIONS ............................................................................................................................... 4 SOLO..............................................................................................................................................................................
INTENTIONALLY BLANK Page 2 May 2022 Version 1.0 www.binsense.
CUSTOMER SUPPORT For warranty service, please contact your local dealer. For product support, troubleshooting, or additional questions with your Bin-Sense™ device, please contact your local dealer (www.binsense.com/locate-a-dealer) or IntraGrain Technologies Inc. at: support@intragrain.com 1.833.570.7979 www.binsense.com Download the Bin-Sense mobile app to set up Bin-Sense Solo! play.google.com/store/apps/ details?id=com.intragrain.binsense mobile apps.apple.
SOLO CERTIFICATIONS SOLO • FCC ID: 2AUTY-106104-SO-LT • Contains FCC ID: XPYUBX19KM01; IC 8595A-UBX19KM01 SOLO-SK • FCC ID: 2AUTY-106104-SO-4G • Contains FCC ID: XPY1EIQ24NN; IC 8595A-1EIQ24NN This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
WHAT THIS WARRANTY DOES NOT COVER This warranty does not cover normal wear of parts or any damage resulting from any of the following: negligent use or misuse of the product; damage in transport, natural disaster, improper installation or use, improper abuse or improper handling. This warranty is limited to only those manufacturing defects that were caused or allowed by IntraGrain. HOW TO OBTAIN WARRANTY SERVICE Please contact the local dealer you purchased the product from.
SAFETY READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Use the Solo device for its intended use only, as described in this manual. Do not use attachments not recommended by the manufacturer. STANDARDS This manual will use the following standard safety terms and conventions to indicate conditions: WARNING: INDICATES A HAZARDOUS SITUATION RESULTING IN SERIOUS INJURY OR DEATH. CAUTION: Indicates a hazardous situation which, if not avoided, could result in moderate injury and/or property damage.
OVERVIEW The Solo unit is used to automatically read up to four sensing cables once daily and send grain condition information to the Bin-Sense Mobile app using a cellular connection. Each bin to be monitored requires the installation of one Solo unit. Two different versions of Solo are available depending on the cellular service available in the area.
INSIDE THE MASTER UNIT A. CELLULAR ANTENNA B. STATUS LED C. 4 X AA BATTERY CLIP D. ADDITIONAL 4 X AA BATTERY CLIP (SOLO 4G/3G ONLY) E. SIM CARD F. TEST BUTTON G. RESET BUTTON Figure 2: Bin-Sense Solo - Interior Page 8 May 2022 Version 1.0 www.binsense.
INSTALLATION WARNING: FALL HAZARD - EXTREME CARE AND CAUTION MUST BE USED WHEN CLIMBING IN A BIN OR SILO. BE SURE TO USE APPROVED SAFETY PROCEDURES AND MATERIALS. WHEN WORKING ABOVE 1.2 METERS, WEAR A SAFETY HARNESS OR PERSONAL PROTECTIVE EQUIPMENT. AN APPROVED TOOL BELT MUST BE WORN TO KEEP BOTH HANDS FREE WHEN CLIMBING UP AND DOWN A LADDER. INSTALLATION TIPS • Solo units can be installed on the top or bottom of the bin.
SOLO UNIT INSTALLATION Carry the Solo unit and any tools and accessories to the top of the bin in a manner that allows both hands free to safely climb the bin. 1. Place the Solo unit on the bin with the antenna fin end of the enclosure closest to the ground. The sensor link cable should point towards the ground to prevent water from running towards the enclosure. The magnetic feet will hold the unit in place on the bin. Figure 3: Bin-Sense Solo Unit Placement 2.
DIAGNOSTICS LED DIAGNOSTICS The diagnostic LED on the Solo units give information about any attached sensor cables as well as cellular connection status. STARTUP STATUS When a Solo device is first powered on and connecting the Bin-Sense servers, the status LED will show different colour and flash patterns to convey the current status.
Flash Colour Value Orange 10 Green 1 The status LED will only flash a specific number of red flashes if the corresponding number is not zero. For example, if there are no moisture cables connected to the Solo unit, the LED will not flash three red flashes. If nothing is detected on the sensor cable interface, the LED will flash once. Figure 4: Diagnostic LED Sequence Page 12 May 2022 Version 1.0 www.binsense.
Manufactured in Canada by: Head Office: IntraGrain Technologies Inc. 118 Husum Road RM of Sherwood, SK CANADA S4K 0A4 support@intragrain.com 1-833-570-7979 www.binsense.