LIVE SYSTEM STARTUP MANUAL 700053-BS March 2022 Version 1.
INTENTIONALLY BLANK 700053-BS March 2022 Version 1.
TABLE OF CONTENTS INTRODUCTION CUSTOMER SUPPORT .................................................................................................................................. 3 BIN-SENSE LIVE CERTIFICATIONS .............................................................................................................. 4 MANUFACTURER’S WARRANTY ................................................................................................................. 5 HOW TO OBTAIN WARRANTY SERVICE .................
CUSTOMER SUPPORT For warranty service, please contact your local dealer. For product support, troubleshooting, or additional questions with your Bin-Sense™ device, please contact your local dealer (www.binsense.com/locate-a-dealer) or IntraGrain Technologies Inc. at: support@intragrain.com 1.833.570.7979 www.binsense.com www.binsense.com March 2022 Version 1.
BIN-SENSE LIVE CERTIFICATIONS FCC ID MASTER UNIT: 2AUTY-106103MU-V06 • Contains FCC ID: XPY1EIQ24NN; IC: 8595A-1EIQ24NN FCC ID REMOTE UNIT: 2AUTY-106103RU-V06 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
MANUFACTURER’S WARRANTY INTRAGRAIN LIMITED ONE-YEAR WARRANTY IntraGrain Technologies Inc. (IntraGrain) warrants that for a period of one (1) year from the date of original purchase, this product will be free from defects in material and workmanship. IntraGrain, at its option, will repair or replace this product or any component of the product found to be defective during this warranty period. Replacement will be made with a new or re-manufactured product or component. No warranty is provided for batteries.
SAFETY READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS. Use the Bin-Sense device for its intended use only, as described in this manual. Do not use attachments not recommended by the manufacturer. STANDARDS This manual will use the following standard safety terms and conventions to indicate conditions: WARNING: INDICATES A HAZARDOUS SITUATION RESULTING IN SERIOUS INJURY OR DEATH.
OVERVIEW The Bin-Sense Live system consists of a Master unit and one or more Remote unit(s). Remote units (installed on each grain bin), read temperature and moisture data via sensing cables. The grain condition data is then wirelessly transmitted to the Master unit. The Master unit is also installed on a grain bin and reads the temperature and moisture sensing cables on that bin.
INTENTIONALLY BLANK Page 8 March 2022 Version 1.0 www.binsense.
OPERATION MASTER UNIT OPERATION Master units operate on a repeating 68-minute cycle. In each cycle, the Master unit will read its own cables, communicate with each Remote unit, and call-in to the Bin-Sense servers. When not performing one of these tasks, the Master unit will go into a low power sleep mode to preserve battery life. Master units communicate with Remote units one at a time and communicate with Remote units in the same order every cycle.
LISTENER MODE Listener mode allows a Master unit to reconnect to a running Bin-Sense Live site if the Master unit power is interrupted. A Master unit will start up listener mode when it has Remote units associated and was previously operating normally. In listener mode, the diagnostic LED will blink green once per second and the Master unit will listen for wireless signals from Remote units still running on the site.
Remote units, it will connect to any new Remote units powered on in the last 68 minutes. It is important to make sure the Master unit has been sent scan commands to keep looking for new Remote units. This method works well on large sites that require numerous man-hours to install the Bin-Sense Live system as each Master unit and Remote unit must only be handled once during the installation process, and Remote units connect to the Master unit within 68 minutes of being powered on. www.binsense.
Manufactured in Canada by: Head Office: IntraGrain Technologies Inc. 118 Husum Road RM of Sherwood, SK CANADA S4K 0A4 support@intragrain.com 1-833-570-7979 www.binsense.