3. Before Starting the Installation 3.4. Recommended Installation Tools Introduction This section describes all the recommended tools for installation of WiBASTM OSDR-HUB and WiBASTM G5 micro-BS / evo-BS. Prerequisites It is installer responsibility to provide the tools for equipment installation. Equipment installation tools Item 1 Tool / Photo Description Adjustable torque U-wrench tool (up to 29 mm opening and supporting max tightening torque 40 Nm). Used for tightening screws and nuts.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 Recommended Installation Tools, Continued Termination of cables Type of cables to be terminated: Ethernet (S-FTP) (ETH-CAB-SFTP). Power supply cable (AC-PWR-CAB, DC-PWR-CAB-1 / 2 / 3). Grounding (GND-CAB6-ID, GND-KIT16-OD). Item Specific works Tool / Photo Description 1 Blade. 2 Cable cutter. 3 Pliers (long nose). 4 CRIMP-TOOL-S 5 Ethernet cable tester. 6 7 Crimping tool for 6 mm2 and 16 mm2 grounding cable.
4. Installation Procedures 4.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 4.1.
4.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna Introduction This paragraph describes the installation procedures that needs to be followed when combining the Base Station radios and sectoral antennas that are listed below: Radio Units Frequency (GHz) – Form Factor WiBASTM OSDR-HUB 10.
4.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna, Continued Radio unit packing materials OSDR-26-H-1008-01 or OSDR-10-H-350 Antenna packing materials HANT2690V-MB Radio unit. BRA-1090V-I Tool Kit packing materials Details SEC-ANT-XPOL-KIT Details Antenna. Pole mounting kit. Greasing paste. Installation leaflet. Antenna. Pole mounting kit. Greasing paste. Installation leaflet.
4. Installation Procedures WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna, Continued Prerequisites Assembly the antenna as per the installation manual inside the box. Precautions This procedure includes antenna adjustment verticality with respect to the ground. Installation tools Adjustable torque u-wrench, allen key, digital inclinometer, wrench (13 mm) and screw drivers.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna, Continued Procedure How to install the antenna of 26 or 28 GHz, proceed as follows: Step 1 Action Follow the included instructions to assemble the antenna mount and attach it to the antenna. The antenna installation should be as shown below.
4. Installation Procedures WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna, Continued Procedure, continued Step 2 Action Use the allen key (included in package) to install the tool as shown below.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.
4. Installation Procedures WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna, Continued Procedure, continued Step 4 Action Perform radio unit installation οnto the antenna, as follows: Lubricate the antenna O-ring with silicone grease. Unlock the four latches of the radio unit, as shown below.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna, Continued Procedure, continued Step 5 Action Use the wrench key (13 mm) to loosen the 3 nuts, as shown below: Do not remove the nuts.
4. Installation Procedures WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna, Continued Procedure, continued Step Action 6 Perform the following actions: Place the inclinometer. Easy rotate (left-right) the radio unit till the inclinometer digital indicator reaches 0 degrees. 7 Use the wrench key (13 mm) to fully tighten the 3 nuts, as shown below: OFFSET RIGHT OFFSET LEFT Do not over tighten.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna, Continued Procedure, continued Step 8 Action Use the u-wrench tool to perform azimuth adjustment, as described to the antenna included instructions. Use the u-wrench tool to perform elevation adjustment, as described to the antenna included instructions. Use the allen key (included in package) to remove the tool. Do not over tighten.
4. Installation Procedures WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna, Continued Procedure How to install the antenna of 10.5 GHz, proceed as follows: Step 1 Action Follow the included instructions to assemble the antenna mount and attach it to the antenna. The antenna installation should be as shown below. The antenna is capable to be installed in both side of the pole The photo is indicative of the installation in the right orientation of the antenna model.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.
4. Installation Procedures WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna, Continued Procedure, continued Step 4 Action Perform radio unit installation onto the antenna, as follows: Lubricate the antenna O-ring with silicone grease. Unlock and open the radio unit latches and mount it to the antenna hooks. Lock and secure all four latches according to the pattern below: End of procedure.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna Introduction This paragraph describes the installation procedures that needs to be followed when combining the Base Station radios and sectoral antennas that are listed below: Radio Units Frequency (GHz) – Form Factor WiBASTM G5 micro-BS evo-BS 28 24.25-29.
4.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna, Continued Radio unit packing materials WMBS-28-L-1008-01 or WG5-EVO-BS-27-29 Packing Materials Radio unit. Materials for installing radio unit to HANT2890V antenna: Set of latches (x4) M6 x 12 mm screws (x8) M6 lock washers (x8) The following materials are not used.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna, Continued Installation tools Adjustable torque U-wrench, wrench (13 mm) and screw driver. Prerequisite Assembly the antenna as per the installation manual inside the box. DO NOT INSTALL THE HOOKS. Procedure Prerequisite Take into account the steps 2, 5, 6, 7 and 8 as described in procedure of WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna on page 83.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna, Continued Procedure, continued Step 2 Action Use the u-wrench to install the antenna latches, as shown below: From order code WMBS-OB-U-DSDS-SB or WG5EVO-BS-LB-UB use the following materials: Set of latches (x4) M6 x 12 mm screws (x8) M6 lock washers (x8) Do not over tighten. Adjust the tool for applying maximum tightening torque 2.0 Nm.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna, Continued Procedure, continued Step 3 Action Perform the following antenna actions: Remove the plastic sticker (A) Lubricate the O-ring with silicone grease (B).
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna, Continued Procedure, continued Step 5 Action Lock and secure all four latches according to the pattern below: End of procedure.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna with MTK-DMA-BX Mounting Kit Introduction This paragraph describes the installation procedures that needs to be followed when combining the Base Station radios and sectoral antennas that are listed below: Radio Units Frequency (GHz) – Form Factor WiBASTM G5 micro-BS evo-BS 28 24.25-29.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna with MTK-DMA-BX Mounting Kit, Continued Overview The following materials table for installation contains indicative order codes: WMBS-28-L-1008-01 or WG5-EVO-BS-27-29 MTK-DMA-BX HANT2890V-MB DO NOT USE ANTENNA POLE MOUNTING KIT. USE THE MOUNTING KIT WITH ORDER CODE MTK-DMA-BX.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna with MTK-DMA-BX Mounting Kit, Continued Radio unit packing materials WMBS-28-L-1008-01 or WG5-EVO-BS-27-29 Packing Materials Radio unit.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna with MTK-DMA-BX Mounting Kit, Continued Pole mounting kit packing materials MTK-DMA-BX Packing Materials Elevation bracket (A). Azimuth bracket (B). Pole bracket (C). Pole hose clamps (x2): Clamp diameter: 64 mm to 140 mm Pole diameter: 48 mm to 100 mm. Set-A: M8 x 25 mm screws (x4). M8 lock washers (x4). M8 washers stainless steel (x4). Set-B: M8 x 25 mm screws (x4). M8 lock washers (x4).
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure (option-1) Prerequisite Take into account the steps 2, 5, 6, 7 and 8 as described in procedure of WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna on page 83.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure (option-1), continued Step 2 Action Perform the following actions: Mount azimuth bracket onto the pole bracket (A) and then install Set-A (x 2) and Set-B (x 2), as shown below. Mount elevation bracket onto the azimuth bracket (B) and then install Set-A (x2) and Set-B (x2), as shown below. Use the tool with M8 hexagon female bit to slightly tighten the screws.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure (option-1), continued Step 3 Action Turn the radio unit to reach the desirable polarization, as shown below: For how to turn the radio unit, follow the polarization label.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure (option-1), continued Step 4 Action Perform the following actions: Install the radio unit onto the elevation bracket.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure (option-1), continued Step 5 Action Use the u-wrench to install the antenna latches, as shown below: From order code WMBS-OB-U-DSDS-SB or WG5EVO-BS-LB-UB use the following materials: Set of latches (x4) M6 x 12 mm screws (x8) M6 lock washers (x8) Do not over tighten.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure (option-1), continued Step 6 Action Perform the following antenna actions: Remove the plastic sticker (A) Lubricate the O-ring with silicone grease (B).
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 Integrated Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure (option-1), continued Step 8 9 Action Verify that the installation appears, as follows (vertical) : Use the U-wrench tool to fully tighten the M8 screws of the mounting kit. Do not over tighten. Adjust the tool for applying maximum tightening torque 17.8 Nm. End of procedure.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 or 180 Antenna with MTK-DMA-BX Mounting Kit Introduction This paragraph describes the installation procedures that needs to be followed when combining the Base Station radios and sectoral antennas that are listed below: Radio Units Frequency (GHz) – Form Factor Antenna Order Codes WiBASTM G5 micro-BS evo-BS 28 24.25-29.
4.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 or 180 Antenna with MTK-DMA-BX Mounting Kit, Continued Radio unit packing materials WMBS-28-L-1008-01 or WG5-EVO-BS-24-26 / WG5-EVO-BS-27-29 Packing Materials Radio unit.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 or 180 Antenna with MTK-DMA-BX Mounting Kit, Continued Tool Kit packing materials SEC-ANT-XPOL-KIT Details Universal antenna alignment tool. 4mm ball-ended hexagon socket screw key.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 or 180 Antenna with MTK-DMA-BX Mounting Kit, Continued Pole mounting kit packing materials MTK-DMA-BX Packing Materials Elevation bracket (A). Azimuth bracket (B). Pole bracket (C). Pole hose clamps (x2): Clamp diameter: 64 mm to 140 mm Pole diameter: 48 mm to 100 mm. Set-A: M8 x 25 mm screws (x4). M8 lock washers (x4). M8 washers stainless steel (x4).
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 or 180 Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure Prerequisite Take into account the steps 2, 5, 6, 7 and 8 as described in procedure of WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna on page 83. How to install WiBASTM G5 micro-BS / evo-BS to HANT28180V or HANT28180H antenna, proceed as follows: The installation procedure for sectoral 900 or 1800 is common.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 or 180 Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure, continued Step 2 Action Perform the following actions: Mount azimuth bracket onto the pole bracket (A) and then install Set-A (x 2) and Set-B (x 2), as shown below. Mount elevation bracket onto the azimuth bracket (B) and then install Set-A (x2) and Set-B (x2), as shown below.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 or 180 Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure, continued Step 3 Action Turn the radio unit to reach the desirable polarization, as shown below: For how to turn the radio unit, follow the polarization label.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Sectoral 90 or 180 Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure, continued Step 4 Action Perform the following actions: Install the radio unit onto the elevation bracket.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 or 180 Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure, continued Step 5 Action Use the u-wrench to install the antenna latches, as shown below: From order code WMBS-OB-U-DSDS-SB or WG5EVO-BS-LB-UB use the following materials: Set of latches (x4) M6 x 12 mm screws (x8) M6 lock washers (x8) Do not over tighten. Adjust the tool for applying maximum tightening torque 2.0 Nm.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Sectoral 90 or 180 Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure, continued Step 8 9 10 Action Open antenna latches and then mount the antenna onto the radio as shown below (the following picture shows vertical polarization): Lock and secure all antenna latches. Verify that the installation appears, as follows: Use the U-wrench tool to fully tighten the M8 screws of the mounting kit. Do not over tighten.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.
4. Installation Procedures WiBAS G5 dual-BS and Dual-Polarization Sectoral 90 Integrated Antenna, Continued Radio unit packing materials WG5-DUAL-BS-L-1008-SB Details WiBASTM G5 dual-BS radio unit (A). M20 Gland for the SFP interfaces for cable diameter range 4.5 mm to 7.5 mm (blue seal) (B). DC power supply connector, 2 sockets, solder type, IP68, UV rated, industrial (PWR-CONN-GX) (C). Applicable cable diameters range is 6.8 mm to 9.5 mm.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 dual-BS and Dual-Polarization Sectoral 90 Integrated Antenna, Continued Prerequisites Assembly the antenna as per the installation manual inside the box. Precautions This procedure includes antenna adjustment verticality with respect to the ground. Installation tools Adjustable torque U-wrench, digital inclinometer, wrench (13 mm) and screw drivers.
4. Installation Procedures WiBAS G5 dual-BS and Dual-Polarization Sectoral 90 Integrated Antenna, Continued Procedure, continued Step 2 Action Perform radio unit installation into the antenna, as follows: Remove antenna feeder plastic protection sticker. Lubricate the antenna O-ring with silicone grease.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.
4. Installation Procedures WiBAS OSDR-HUB and Sectoral 180 Integrated Antenna, Continued Radio unit packing materials OSDR-28-H-1008-01 Antenna packing materials HANT28180V-MB Tool Kit packing materials SEC-ANT-XPOL-KIT Details Radio unit. Details Antenna Pole mounting kit. Greasing paste. Installation leaflet. Details Universal antenna alignment tool. 4mm ball-ended hexagon socket screw key.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS OSDR-HUB and Sectoral 180 Integrated Antenna, Continued Prerequisites Assembly the antenna as per the installation manual inside the box. Precautions This procedure includes antenna adjustment verticality with respect to the ground. Installation tools Adjustable torque U-wrench, allen key and screw drivers.
4. Installation Procedures WiBAS OSDR-HUB and Sectoral 180 Integrated Antenna, Continued Procedure Prerequisite Take into account the steps 2, 5, 6, 7 and 8 as described in procedure of WiBAS OSDR-HUB and Sectoral 90 Integrated Antenna on page 83. How to install the WiBASTM OSDR-HUB to HANT28180V-MB antenna, proceed as follows: Step Action 1 Assembly the antenna as per the installation manual inside the box.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.
4. Installation Procedures WiBAS OSDR-HUB and Sectoral 180 Integrated Antenna, Continued Procedure, continued Step 5 Action Perform radio unit installation into the antenna, as follows: Lubricate the antenna O-ring with silicone grease. Unlock the four latches of the radio unit, as shown below: Pass the latches to antenna hooks, as shown below: Lock and secure all four latches according to the pattern below: End of procedure.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.
4.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS OSDR-HUB and Omnidirectional 360 Antenna with OSDR-360-ANT-MNT-KIT Mounting Kit, Continued Radio unit packing material OSDR-28-H-1008-01 Antenna packing materials HANT2628360V Antenna adaptation kit packing materials Packing Materials Radio unit. Packing Materials Antenna. Installation leaflet. Greasing paste. OSDR26-360-ANT-ADAPT-KIT OSDR28-360-ANT-ADAPT-KIT Packing Materials Antenna adaptation kit.
4. Installation Procedures WiBAS OSDR-HUB and Omnidirectional 360 Antenna with OSDR-360-ANT-MNT-KIT Mounting Kit, Continued Pole mounting kit packing materials OSDR-360-ANT-MNT-KIT Packing Materials Omni pillar bracket (A). Spacer plate (B). Mounting bracket (C). Pole hose clamps (x2): Clamp diameter: 64 mm to 140 mm Pole diameter: 48 mm to 100 mm. Set-A Set-B Set-D Set-C Set-C & D Set-E Set-A: M8 x 25 mm screws (x2). M8 lock washers (x2). M8 washers stainless steel (x2).
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS OSDR-HUB and Omnidirectional 360 Antenna with OSDR-360-ANT-MNT-KIT Mounting Kit, Continued Installation tools Adjustable torque wrench with hexagon female bit U-wrench. Allen key (1.5 and 2.5 mm). Spanner key for M5 screw.
4.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS OSDR-HUB and Omnidirectional 360 Antenna with OSDR-360-ANT-MNT-KIT Mounting Kit, Continued Procedure, continued Step 3 Action Install the set of pole mounting kit packing list materials, as shown below: Use the tool with M8 hexagon female bit to fully tighten the screws. Do not over tighten. Adjust the tool for applying maximum tightening torque 19.3 Nm. 4 Use the allen key (2.
4.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS OSDR-HUB and Omnidirectional 360 Antenna with OSDR-360-ANT-MNT-KIT Mounting Kit, Continued Procedure, continued Step 7 Action Perform the following actions: Install the adaptation plate onto the antenna (A), as described to INSTALLATION INSTRUCTION leaflet (included in adaptation kit package).
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Omnidirectional 360 Antenna with MTK-DMA-BX Mounting Kit Introduction This paragraph describes the installation procedures that needs to be followed when combining the Base Station radios and sectoral antennas that are listed below: Radio Units Frequency (GHz) – Form Factor Antenna Order Code WiBASTM G5 micro-BS evo-BS 28 24.25-29.50 HANT2628360V √(2) √(2) WiBASTM G5 evo-BS requires external GNSS module kit installation.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Omnidirectional 360 Antenna with MTK-DMA-BX Mounting Kit, Continued Radio unit packing materials WMBS-28-L-1008-01 or WG5-EVO-BS-26-28 Packing Materials Radio unit.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Omnidirectional 360 Antenna with MTK-DMA-BX Mounting Kit, Continued Pole mounting kit packing materials MTK-DMA-BX Packing Materials Elevation bracket (A). Azimuth bracket (B). Pole bracket (C). Pole hose clamps (x2): Clamp diameter: 64 mm to 140 mm Pole diameter: 48 mm to 100 mm. Set-A: M8 x 25 mm screws (x4). M8 lock washers (x4). M8 washers stainless steel (x4).
4.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Omnidirectional 360 Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure, continued Step 2 Action Perform the following actions: Mount azimuth bracket onto the pole bracket (A) and then install Set-A (x 2) and Set-B (x 2), as shown below. Mount elevation bracket onto the azimuth bracket (B) and then install Set-A (x2) and Set-B (x2), as shown below.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Omnidirectional 360 Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure, continued Step Action 3 Use the allen key (2.5 mm) to remove the following M5 x 6 mm screws (x4) form radio unit: 4 Install the antenna to radio unit as described in the installation leaflet of antenna package.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 micro-BS / evo-BS and Omnidirectional 360 Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure, continued Step 5 Action Perform the following actions: Install the radio unit onto the elevation bracket.
4. Installation Procedures WiBAS G5 micro-BS / evo-BS and Omnidirectional 360 Antenna with MTK-DMA-BX Mounting Kit, Continued Procedure, continued Step 6 Action Verify that the installation appears, as follows (the following picture shows vertical polarization installation example): 7 Use the tool with M8 hexagon female bit to fully tighten the screws. Do not over tighten. Adjust the tool for applying maximum tightening torque 17.8 Nm. End of procedure.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 evo-BS and Parabolic Integrated Antenna, 0.6 m This paragraph describes the installation procedures that needs to be followed when combining the Base Station radios and parabolic antenna that are listed below: Radio Units Frequency (GHz) – Form Factor WiBASTM G5 evo-BS Antenna Order Code 24.25-29.50 ANT-IS-2628-2F-C √(1) Parabolic antenna is used with WiBASΤΜ G5 evo-BS only for Point-to-Point operation.
4. Installation Procedures WiBAS G5 evo-BS and Parabolic Integrated Antenna, 0.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 evo-BS and Parabolic Integrated Antenna, 0.6 m, Continued Radio unit packing materials WG5-EVO-BS-27-29 Packing Materials Radio unit. Materials for installing radio unit to ANT-IS-2628-2F-C antenna: Set of latches (x4) M6 x 12 mm screws (x8) M6 lock washers (x8) The following materials are not used.
4. Installation Procedures WiBAS G5 evo-BS and Parabolic Integrated Antenna, 0.6 m, Continued Procedure How to install the WiBASTM G5 evo-BS to ANT-IS-2628-2F-C antenna, proceed as follows: Step 1 Action Follow the included instructions to assemble the antenna mount and attach it to the antenna. The antenna installation should be as shown below.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 evo-BS and Parabolic Integrated Antenna, 0.6 m, Continued Procedure, continued Step 2 Action Perform the following antenna actions: Remove the plastic sticker (A) Lubricate the O-ring with silicone grease (B).
4. Installation Procedures WiBAS G5 evo-BS and Parabolic Integrated Antenna, 0.6 m, Continued Procedure, continued Step 3a Action Radio unit and antenna should be adjusted for common polarization, as shown below.
WiBAS / WiBAS G5 Base Stations Installation & Cabling Manual - Edition 3.2 WiBAS G5 evo-BS and Parabolic Integrated Antenna, 0.
4. Installation Procedures WiBAS G5 evo-BS and Parabolic Integrated Antenna, 0.6 m, Continued Procedure, continued Step 4 Action Lock and secure all four latches according to the pattern below: End of procedure.