Contents Ⅰ Installation Manual 1. Hardware Installation 2. Software Installation Ⅱ User Manual 3. User Manual- Server 01. Main Program 02. Search Program 03. AVI Backup Manager 04. Backup Manager 4. User Manual- Client 01. NetClient Program 02. WebClient Program ※ Annex Annex 1. I/O Device Annex 2. Dynamic IP Annex 3.
Ⅰ Installation manual - Hardware Installation 2. DVR Audio Installation 1. Hardware Installation Please check contents before installation: DVR Board, Extension Cable, Audio & PTZ Installation, etc., if you are missing any parts please contact your local dealer. 2-1. Prepare DVR PC and MIC. 2-2. Connect the MIC to the Mainboard MIC Port of DVR PC OR the Audio IN port on DVR Board. Please connect the Speaker to the back panel of DVR PC. 1. DVR Board & Extension Cable Installation 1-1.
Ⅰ Installation manual - Hardware Installation - HP Board: Connect the 8CH MIC(B) to DVR Board(A) starting from the top. 3. P/T/Z Installation 3-1. P/T/Z Cable [A] Cable : Connect to COM port of DVR PC [B] Cable : Connect to DVR Board [C] Cable : Connect to Receiver Cable <8CH> B A C - RC Board: Connect the 4CH MIC(B) to DVR Board(A) starting from the left. 4. Real Display(RD) Board Installation 4-1.
Ⅰ Installation manual - Software Installation 5. I/O Board Installation 1. Software Installation 5-1. Prepare Sensor, Alarm, I/O Board and I/O Extension Board for I/O Board Installation. < 8 port In/Out Connection> 4CH Input 5CH Output You can install SmartDVR Software by using SmartDVR Formula CD or downloading from INTOTECH website, www.intotech.co.kr. Software CD consists of Server Package (Main program, WebClient program, Apache HTTP Server program), Client Package (NetClient program) & AVI Codec.
Ⅰ Installation manual - Software Installation 1. SmartDVR Apache HTTP Server (Web Server) Installation 1-1 Installation wizard tool will appear. Click [Next]. 1-2 Read the License Agreement and if you agree to the contents, select [I accept…] and click [Next]. 1-3 Click [Next] after checking server information of Apache HTTP Server. 1-4 Insert Network Domain, Server Name, Administrator’s E-mail Address. (This procedure is only a formality.
Ⅰ Installation manual - Software Installation 12 1-5 Select Setup Type as [Complete] and click [Next]. 1-7 After the setting is finished, click [Install] and start installation. 1-6 Click [Next] without change of setting. Note: Do not change the directory! 1-8 After the installation is done, click [Finish].
Ⅰ Installation manual - Software Installation 1-9 After the installation is finished, a message confirming the change of the Server port of Apache will appear. 2-2 Check the contents of License Agreement; if you agree to the contents, click [Yes]. 2 SmartDVR WebClient Installation 2-1 After the Installation Wizard Tool is appeared, click [Next]. 2-3 After the installation is done, click [Finish].
Ⅰ Installation manual - Software Installation 3 SmartDVR Formula Installation 3-1 After Installation Wizard Tool is appeared, Click [Next]. 3-2 Check the details of License Agreement; if you agree to the contents, click [Yes]. 16 3-3 After choosing [Destination Folder] for installation, click [Next]. 3-4 After the installation is done, click [Finish].
Ⅰ Installation manual - Software Installation 3-5 Driver Installation: Wizard automatically installs drivers according to each board type. 5 NetClient Installation 5-1 After the Installation Wizard Tool is appeared, click [Next]. 3-6 Reboot PC after all the installation. 4. SmartDVR Formula Uninstallation 4-1 Goto [Start] – [Control panel] and click [Add/Remove Program]. 4-2 Select [SmartDVR Formula] and click [Change/Remove]. 5-2 After choosing [Destination Folder] for installation, click [Next].
Ⅰ Installation manual - Software Installation 5-3 After the installation is finished, click [Finish] AVI Codec Installation Click the icon below and AVI Codec installation will proceed. 7-1 AVI Codec Installation diagram. 6 NetClient Uninstallation 6-1 Goto [Start] – [Control panel] and click [Add/Remove Program]. 6-2 Select [NetClient Plus] and click [Change/Remove]. 7-2 After the installation is finished, click [Finish].
Ⅱ User Manual - Main Program 1-1 Control Panel Control Panel consists of the following icons: This enables users to run search programs, manually record images and open configuration window. 3 Main Program 01. Main Program Main Program enables users to monitor images through PC monitor. The main program supports the following functions: record images, search & playback images and control camera remotely. Image can also be transmitted over the network to any remote site.
Ⅱ User Manual - Main Program 1-4 Camera Selection Panel Click specific channel from Camera Selection Panel to enlarge and view images. 1-5 Audio Volume Control Bar If Audio input is configured from [Configuration] - [General], audio volume can be controlled from Audio Volume Control Bar. Disk Full Internet(TCP) Conection CH No. Modem Conection CH No.
Ⅱ User Manual - Main Program Audio Input Setup the Gain of Audio Input. - AUD1 ~ AUD8 is gain control for Audio Input from Capture Board. Set the gain to minimum(0) when use of amplified mic. (e.g.: camera built-in mic) - Snd Card is audio volume control using Sound Card as output device. 2 Channel Video/Audio Setup - Setup Camera Input Type NTSC – Korea, USA, Japan, Australia(some region), North Amercia(some region) etc. PAL – Region excluding NTSC area(China, Europe, South America, etc.
Ⅱ User Manual - Main Program 2 Store 3 Network ※ Store Disk – Indicates installed HDD Capacity. Check(√) HDD to use as recording device Notice) Recommend to disable C Drive(Operating System installed) as recording device and use other drives(D, E, C). ※ Server Setup - Enable the Network Server: Setup System to be used as Internet Server. Server image can be viewed from remote Client Program OR Internet Web Browser by using private line connected to internet.
Ⅱ User Manual - Main Program 4 Schedule Recording Modes: Full Recording, Motion Detected Recording, Sensor Recording is possible for a specific date, time and channels. 5 System Auto Reboot Setup specific time to automatically reboot system. e.g.) Setup Recording Schedule for Monday 0~12 hour, Setup Motion Detection Recording Schedule for Tuesday 13~23 hour, Setup Sensor Recording Schedule for Wednesday 0~24 hour.
Ⅱ User Manual - Main Program 6 Event ※ Sensor Input - Check [Enable the Sensor] and configure the channel of camera and sensor input channel. ※ Enable Event Recording - Use Digital Output OR auto-recording when there is sensor input signal. 7 Receiver ※ Port Setup: Select serial port to use PAN/TILT Camera OR Receiver. ※ Device Type: Select protocol of receiver from Device Type Panel. 8 Video Out e.g.) Configure 1,2,3,4 Sensor Input for CH1 Camera & 5,6,7,8 Digital Output.
Ⅱ User Manual - Search Program 9 User Management 02.Search Program Search Program allows users to search by time/date & play recorded images and audio. Support saving of still image by .bmp format, printing of still image, watermarked .bmp file of each image. User Managemet can give different authorization levels for management in accord to user IDs. Insert & Modify User Information Insert ID & Password and click [Modify User Information] icon to add new user.
Ⅱ User Manual - Search Program Calendar 1-2 Playback Control Panel [Playback Control Panel] MD ONLY Icon: Load Motion Detected data only. LOAD Icon: Load data of selected date from calendar. - Save Icon: Save image of selected channels - Print Icon: Print image of selected channels using printer. Supports playback options: 1x, 4x playback, reverse playback, frame by frame playback. 1-3 Screen Partition Panel [Screen Partition Panel] Support 8 kinds of various screen partition display.
