Installation Instructions (Continued) Step #5 Battery Installation/Application of Front Plate/Optional Gasket • Tighten lockbody screws • Attach front plate and retain with (2) flat head screws Security Screw Front plate • Outside of Door Security tool 01-0297 included (2) Flat head screws • Place (6) AA batteries into the compartment as indicated • Observe polarity when installing “AA” batteries • Attach battery cover to inside escutcheon making sure to line up tabs with retaining slots in battery
7 Operational Check • Place key into cylinder and rotate key. • The key will retract the latchbolt. • If the deadbolt is thrown, the key will retract both the deadbolt and the latchbolt. • Inside handle lever retracts latchbolt and deadbolt (if provided).
8 Programming Instructions for Keypad Operations Only • Soflink™ Plus must be used with (PA) controller for programming • The Master Code is always User “01”. The Master Code assigns the Emergency and Supervisory Codes. It is also used for programming. Users are deleted through the Master Programming Code only • The Emergency Code is always User “02”. The Emergency Code will override the deadbolt in the mortise lock and has an unlock time of 10 seconds • The Supervisory Code is always User “03”.
To Enter the Emergency Code (Unlock Duration 10 Seconds) 99# Master Code* Yellow LED Blinks 50# 2# Emergency Code* Yellow LED Blinks Quickly Emergency Code* Yellow LED Blinks Slowly (If Solid, see Note) * Yellow LED Goes Out To Change the Supervisory Code 99# Master Code* 50# 1# 03# Supervisory Code* Supervisory Code* * • Factory Default Supervisory Code is Yellow Yellow Yellow Yellow 4321 LED LED LED LED Blinks Blinks Quickly Blinks Slowly (If Solid, see Note) Goes Out To Enter a User Code 99# Supervis
To Program Door Name into Keypad 99# Master Code* Yellow LED Blinks 43# 0# Door Name# (Must be four digits) Yellow LED Blinks * Yellow LED Blinks Quickly * Yellow LED Blinks Slowly (If Solid, see Note) * Yellow LED Goes Out If SofLink™ Plus is being used, door name must be changed via PC To Interrogate Transaction Log 99# Supervisory or Master Code* Yellow 70# 0# 0# Yellow * Yellow * Yellow For additional information, see “Transaction Log”. Note: Seq. # 0 is the programming request to output the entries.
To Disable / Enable a User Number 99# Master Code* 56# 0# = Enable (1# = Disable), User# * * * To Set Unlock Time Master Code* 11# Time Duration# (01-99sec) 0# * * * The Unlock Time is adjustable foe Momentary recommended to extend battery life. Once the ALL users except 02.
To Change the Supervisor Code 99# Master Code* 3# Supervisory (1-6 Digit)* Supervisory (1-6 Digit)* * • Factory Default Supervisory Code is Yellow Yellow Yellow Yellow Yellow 4321 LED LED LED LED LED Blinks Blinks Blinks Quickly Blinks Slowly (If Solid, see Note) Goes Out Enter A User Code 99# Master Code* 50# 1# (User Number 04-500)# User Code (1-6 Digit)* User Code (1-6 Digit)* * Yellow Yellow Yellow Yellow Yellow LED LED LED LED LED Blinks Blinks Blinks Quickly Blinks Slowly (If Solid, see Note) G
To Clear the Entire Memory 99# Master Code* 46# 00000# 00000# * * * Yellow LED Blinks Yellow LED Blinks Yellow LED Blinks Quickly Yellow LED Blinks Very Fast for 10 sec.
Set Unlock Time 99# Master Code* 11# (1-99 sec.)# 0# * * * Yellow Yellow Yellow Yellow Yellow LED LED LED LED LED Blinks Blinks Blinks Quickly Blinks Slowly (If Solid, see Note) Goes Out To Enable/Disable A User 99# Master Code* 56# 0# (Enable) or 1# (Disable) (User No.
To Erase Transaction Log 99# Master Code* 76# 00000# 00000# * * * * Yellow Yellow Yellow Yellow Yellow Yellow LED Blinks LED Blinks LED Blinks Quickly Blink, Green Fast LED Blinks Slowly (If Solid, see Note) LED Goes Out Note: If the Yellow LED becomes Solid rather than blinking, a mistake has been made. Depress the * Button until the Yellow LED goes out and start programming again.
9 Chain Programming When programming multiple User Numbers and Codes into the Low Profile (LK, LU, PK) Mortise Keypad Lock, it is not necessary to leave and re-enter the programming Mode (50) for each entry. Multiple entries may be chained together and the three different types of user codes (Standard, Passage and One Time) may be mixed. The format to be used is as follows where: “T” is the Type of user code with “1” Standard, “2” Passage and “3” One Time.
10 Transaction Log To output the last 15 or 1000 transactions, enter 99 # Supervisory or Master Code * 70 # 0 # 0 # **. • Examples on this page are for the 100 user, 15 transaction unit + + + - + + + - Note: Seq. # 0 is the programming request to output the entries. Sequence numbers 1-9 are the actual entries.