6 Configure the Computer Use this chapter to learn about the available methods for configuring your mobile computer and how to use Intermec Settings. You can also use this chapter to learn how to configure network communications and wireless security.
Chapter 6 — Configure the Computer How to Configure the Computer You can configure many parameters on the computer such as the bar code symbologies it decodes or the network settings. The values you set for these parameters determine how the computer operates. There are several ways to configure the computer: • Directly on the computer. You can use Intermec Settings directly on the computer to change only the settings on that computer.
Chapter 6 — Configure the Computer Start Intermec Settings Intermec Settings is located on the System screen. • Tap Start > Settings > System > Intermec Settings. The Intermec Settings Main Menu appears. About the Structure of Intermec Settings Use the tables below to help find the parameters in Intermec Settings that you want to configure. Each table contains the parameters for one of the Intermec Settings Main Menu options.
Chapter 6 — Configure the Computer Data Collection Menu Data Collection Options Parameters You Can Configure Internal Scanner • • • • • • • • • • • • • • • • • Bluetooth Scanner Dock Tethered Scanner Camera Symbologies Scanner settings Imager settings Decode security Symbologies Scanner settings Imager settings Decode security Symbologies Scanner settings Scanner port settings Imager settings Decode security Symbologies Scanner settings Camera settings Decode security BT-Configure on Connect Bluet
Chapter 6 — Configure the Computer Communications Options Parameters You Can Configure WWAN Radio • • • • • Serial Port Switch Serial port switch settings (IrDA, docking connector, and back interface) Add WWAN connection Edit WWAN connections Manage WWAN radio Carrier Selection WWAN information Device Settings Menu Device Settings Options Parameters You Can Configure Date and Time Date and time settings Good Read • • • • • • • • Sounds Internal scanner Tethered scanner Bluetooth scanner Beeper
Chapter 6 — Configure the Computer Device Settings Options Parameters You Can Configure Profile Settings Application Whether these parameter options appear in Profile Settings: • Camera • Power • Scanning Features Disabled by Policy None (read-only) Printer Menu Printer Options Parameters You Can Configure Printer (if connected through Bluetooth) Printer settings (Auto detect printer, memory, display, and so on) Note: The Printer menu displays settings for Bluetooth connected printers.
Chapter 6 — Configure the Computer Virtual Wedge Menu Virtual Wedge Options Parameters You Can Configure Enable Virtual Wedge Enable virtual wedge Bar Code Scanner Wedge Bar code scanner wedge settings (bar code scanner grid and label encoding) Magstripe Reader Wedge Magstripe Reader Grid Core Messaging Service Menu Core Messaging Service Options Parameters You Can Configure Server IP Server IP (read-only) Associated Server IP Associated server IP Broadcast Name Broadcast name Port Port (r
Chapter 6 — Configure the Computer Location Services Menu Location Services Options Parameters You Can Configure Server Server settings (port and enable server) Virtual GPS Virtual GPS settings For more information on all parameters in Intermec Settings, see the Intermec Settings Command Reference Manual. Navigate in Intermec Settings You can easily navigate through the screens in Intermec Settings to find the parameter you need to configure.
Chapter 6 — Configure the Computer 3 From the Camera, Power, or Scanning submenu, check or clear the Display check box for the settings you want to have available to the end user. 4 Click OK to save your selection. Restore Default Settings to a Menu You can restore the items in a single menu to their default settings. 1 Navigate to the menu that you want to restore to defaults. 2 Tap Menu > Restore Menu Defaults. 3 When prompted, tap Yes to restore the menu default settings.
Chapter 6 — Configure the Computer Note: When you restore default settings in Intermec Settings, only the settings for visible items are restored to defaults. The settings for hidden menu items are not affected. Use Intermec Settings Remotely with SmartSystems Your mobile computer is SmartSystems-enabled, which lets you open Intermec Settings from the SmartSystems console to remotely configure all of your mobile computers.
Chapter 6 — Configure the Computer Configure 802.11a/b/g/n (Wi-Fi) Radio Communications Make sure all components with antennas are at least 30 cm (1 ft) apart when power is applied. Failure to comply could result in equipment damage. The mobile computer contains an 802.11 radio to transfer data using wireless communications and to support the TCP/IP network protocols. This section of the manual assumes that your wireless network is set up, including your access points. By default, the 802.
Chapter 6 — Configure the Computer 2 Connect the Ethernet cable from your network to the snap-on adapter or dock. Ethernet communications are automatically enabled on your mobile computer. 3 Make sure that your computer is communicating with the network. The network connection icon ( ) should appear on the title bar. Configure Bluetooth Communications Your mobile computer is Bluetooth™-enabled, which lets you connect to other Bluetooth devices, such as scanners, printers, or audio devices.
Chapter 6 — Configure the Computer 4 Tap OK. The Bluetooth radio maintains its state through a reboot or cold boot and maintains virtual COM ports. But, if you clean boot your computer you need to recreate pairings to devices. Connect to a Bluetooth Scanner You can connect the computer to an Intermec Bluetooth scanner, such as the SF51 or SR61. 1 Tap Start > Settings > System > Wireless Scanning.
Chapter 6 — Configure the Computer 2 Tap Add Device. 3 Select Quick Connect, Search, or Manual. Follow the onscreen instruction to add a wireless scanner.
Chapter 6 — Configure the Computer Connect to a Bluetooth Printer To configure your computer for Bluetooth wireless printing, you need to: • • create an application that opens the wireless printing COM port on your computer. For help, see the Bluetooth Resource Kit, which is part of the Intermec Developer Library (IDL), available from the Intermec website at www.intermec.com/idl. select the current wireless printer on your computer. For help, see the next procedure.
Chapter 6 — Configure the Computer Connect to a Bluetooth Audio Device Use the Bluetooth Audio enabler to discover, activate, and connect to Bluetooth audio devices such as a headset. This enables system sounds to be monitored through the headset. 1 Tap Start > Settings > System > Bluetooth Audio. 2 Tap Search to find your Bluetooth headset or hands-free device. 3 Select your device from the list and configure any settings. 4 Click OK when you are done.
Chapter 6 — Configure the Computer Connect to a Tethered Scanner Use this procedure to connect your mobile computer to an SR30, SR61T, or ASCII tethered scanner and enable RS-232 communications. 1 Tap Start > Settings > System > Intermec Settings > Communications > Serial Port Switch. 2 Select Standard docking and IrDA and tap OK. If the serial port switch is set to one of the other options, you need to select Standard docking and IrDA and then save and reboot the computer before you proceed.
Chapter 6 — Configure the Computer 3 Enter a name for the connection, such as “ISP Connection.” 4 If you are using an external modem connected to your mobile computer with a cable, select Hayes Compatible on COM1 from the Select a modem list. 5 Tap Next. 6 Enter the access phone number and then tap Next. 7 Enter the User name, Password, and Domain (if provided by an ISP or your network administrator). 8 Tap Finish. 9 On the Connections screen, tap Advanced on the horizontal scroll. 10 Tap Dialing Rules.
Chapter 6 — Configure the Computer Create a VPN Server Connection You can create a Virtual Private Network (VPN) connection to securely connect to servers, such as a corporate network, through the Internet. Before you can create a VPN connection, you need this information from your network administrator: • User name • Password • Domain name • TCP/IP settings • Host name or IP address of the VPN server After you have located this information, you can create a VPN server connection.
Chapter 6 — Configure the Computer About Wireless Security The computer provides five types of security for your wireless network: • Wi-Fi Protected Access 2 (WPA2™) • Wi-Fi Protected Access (WPA) • • 802.1x LEAP • WEP This section explains how to configure wireless security on your mobile computer. Intermec recommends that you implement WPA2 security using PSK (Personal) or 802.1X (Enterprise) key management as appropriate.
Chapter 6 — Configure the Computer • If you are primarily using the computer to connect to Wi-Fi hotspots, you may want to use Microsoft security. To use Microsoft security, you need to select it as your security choice. For help, see “Select Microsoft as Your Security Choice” on page 97. Select a Funk Security Profile You can define up to four profiles for Funk security. Different profiles let your computer communicate in different networks without having to change all of your security settings.
Chapter 6 — Configure the Computer 5 Select the profile you want to configure. 6 For Association, select WPA or WPA2. Encryption automatically defaults to TKIP or AES, respectively. 7 For 8021x, select TTLS, PEAP, EAP-FAST, or TLS. 8 If you selected TTLS, EAP-FAST, or PEAP: a For Prompt for Credentials, select Enter credentials now. b Enter a User Name and User Password. c For Validate Server Certificate, select Yes.
Chapter 6 — Configure the Computer 8 For Pre-Shared Key, enter the pre-shared key or passphrase. The pre-shared key must be a value of 32 hex pairs preceded by 0x for a total of 66 characters. The value must match the key value on the access point. The passphrase must be from 8 to 63 characters. After you enter a passphrase, the 70 Series internally converts it to a pre-shared key. This value must match the passphrase on the authenticator. 9 Save your settings. Configure 802.
Chapter 6 — Configure the Computer 10 If you select TLS: a Load a user and root certificate on your computer. For help, see “Load a Certificate” on page 102. b For Validate Server Certificate, select Yes. c Enter a User Name and Subject Name. 11 Save your settings. Configure LEAP Security with Funk After you configure the communications and radio parameters on your mobile computer and select Funk as your security choice, you can configure LEAP. 1 Start Intermec Settings. 2 Select Communications > 802.
Chapter 6 — Configure the Computer 5 Select the profile you want to configure. 6 For Association, select Open. 7 For Encryption, select WEP. 8 For 8021x select None. 9 Define a value for the keys you want to use. You can define up to four keys (Key 1 through Key 4). Enter an ASCII key or a hex key that is either 5 bytes or 13 bytes long depending on the capability of the radio. Set a 5- byte value for 64-bit WEP or a 13-byte value for 128-bit WEP.
Chapter 6 — Configure the Computer With Microsoft as your security choice, you can configure: • WPA or WPA2 • 802.1x • Static WEP Select Microsoft Security Use the following procedure to select Microsoft security. 1 Start Intermec Settings. For help, see “Configure the Computer” on page 73. 2 Select Communications > 802.11 Radio > Security Choice. 3 From the Security Choice list, select Microsoft Security.
Chapter 6 — Configure the Computer 7 If you selected TLS: a Load a user and root certificate on your computer. For help, see “Load a Certificate” on page 102. b Select Properties. The Certificates dialog box appears. c Select the certificate you want to use from the list. The User Logon dialog box appears. d Enter a User Name and Domain and tap OK. e Tap OK to exit the Certificates dialog box. f Press OK to save the Microsoft Security settings.
Chapter 6 — Configure the Computer 6 For Pre-Shared Key, enter the pre-shared key or the passphrase. The pre-shared key must be a value of 32 hex pairs preceded by 0x for a total of 66 characters. The value must match the key value on the authenticator. The passphrase must be from 8 to 63 characters. After you enter a passphrase, the computer internally converts it to a pre-shared key. 7 Save your settings. Configure 802.1x Security with Microsoft Use the following procedure to configure 802.
Chapter 6 — Configure the Computer 9 If you selected PEAP: a Load a root certificate of the authentication server on your computer. For help, see “Load a Certificate” on page 102. b Press OK to save the security settings and the User Logon dialog box appears. c Enter a User Name, Password, and Domain. Select Save Password if you want to save the password for future authentication sessions. d Press OK to save the Microsoft Security settings. 10 For Network Key Setting, select Automatic.
Chapter 6 — Configure the Computer Use Open (No Security) Associations with Microsoft Use the following procedure to configure your mobile computer for open security using Microsoft WZC. 1 Start Intermec Settings. 2 Select Communications > 802.11 Radio > Microsoft Security. 3 For Network Authentication, select Open. 4 For Data Encryption, select Disabled. 5 Tap OK. Your settings are saved. Load a Certificate To use transport layer security (TLS) with WPA or 802.
Chapter 6 — Configure the Computer 3 Tap Communications > 802.11 Radio > Certificates. The Certificates screen appears. 4 To import a certificate chain: a Tap Import Certificates to install the selected certificate. b In the CertImportUI screen, tap the <<< button next to the Select pfx to import text field. c Select the root certificate from the list. d Tap Import Certificate. 5 To import user and root certificates from a Microsoft IAS server: a Tap Import Certificates. b Tap Web Enrollment.
Chapter 6 — Configure the Computer 104 70 Series Mobile Computer User Manual
7 Manage the Computer Use this chapter to learn how to remotely update, configure, and monitor your Intermec mobile computers. You will also find information on installing and developing software applications as well as how to upgrade the system software.
Chapter 7 — Manage the Computer Manage the Computer in Your Network When you have multiple mobile computers and peripherals in your network, it is essential to have an easy way to manage updates, configure all of the devices, and remotely troubleshoot problems. Intermec provides a free device management software platform called SmartSystems™ Foundation to help you manage your devices. You can also purchase third-party device management software through a vendor.
Chapter 7 — Manage the Computer Intermec SmartSystems Console Through the console, you can: • drag-and-drop configuration bundles, operating system updates, and firmware upgrades to multiple computers. • save configuration settings from a single device and deploy those settings to many devices simultaneously. • remotely change settings on SmartSystems-enabled computers and peripherals.
Chapter 7 — Manage the Computer Manage the Computer Using Third-Party Software You can use third-party software such as Wavelink Avalanche to centrally manage your Intermec devices. Device management software enables you to update software, increase security, track your assets, and troubleshoot devices remotely. You can download the Wavelink Enabler for the mobile computer from the Wavelink website. For more information, visit the Intermec website and search for Wavelink Avalanche or visit www.wavelink.
Chapter 7 — Manage the Computer • The non-volatile Flash File Store. Applications and data in the Flash File Store will persist through a clean boot. Note: The Flash File Store is erased if you reflash the operating system image. Files copied to any of these locations are safe when you cold boot the computer as long as the AutoRun system is installed in the appropriate location. When AutoRun is installed on the computer, all .cab files in the CabFiles folder are automatically extracted after a cold boot.
Chapter 7 — Manage the Computer 3 Reboot or cold boot the computer. 4 After the boot process is finished, browse to the .cab files and tap the files to install them. Install Applications Using a Storage Card Use a storage card to install applications on one computer at a time or if you have no network connection. 1 Copy your application file to the storage card. 2 Install the storage card in the mobile computer. 3 On the mobile computer, browse to the Storage Card folder and run your application.
Chapter 7 — Manage the Computer Update Individual or Multiple Computers Using the SmartSystems Console You can use the SmartSystems console to update the operating system or system software on your mobile computer. The console is part of SmartSystems Foundation and is available from the Intermec website. Before you can update your mobile computer, you need: • SmartSystems Foundation. To download SmartSystems Foundation, go to www.intermec.com/SmartSystems and click the Downloads tab.
Chapter 7 — Manage the Computer Note: The SmartSystems console indicates that your mobile computer is offline, by displaying a red stop symbol, until the computer reboots and reconnects to the system. Update Individual Mobile Computers Using a microSD Card You can transfer upgrade bundles from your desktop PC to your mobile computer using a storage card. Before you can update your mobile computer, you need: • the SmartSystems bundles you want to install.
8 Troubleshoot and Maintain the Computer If you encounter any problems while using the 70 Series computer, look in this chapter to find a possible solution. You will also find information on routine maintenance.
Chapter 8 — Troubleshoot and Maintain the Computer About the Intermec Dashboard The Intermec Dashboard is designed to provide proactive monitoring of your mobile computers to prevent downtime. You can easily see the health of the device and can help pinpoint the source of a problem to determine if it is hardware or software related. Intermec Dashboard displays information such as the status of network connections, battery usage, storage space, and internal devices.
Chapter 8 — Troubleshoot and Maintain the Computer Troubleshoot Your Mobile Computer Use the troubleshooting tables in this section to fix problems with the Wi-Fi connection, 802.1x security, the imager, or general problems with operating the mobile computer. If you send the computer in for service, it is your responsibility to save the computer data and configuration. Intermec is responsible only for ensuring that the hardware matches the original configuration when repairing or replacing the computer.
Chapter 8 — Troubleshoot and Maintain the Computer Problem Solution A network connection icon appears in the The computer may not be communicating with the toolbar, but then disappears. intended access point. Make sure the network name matches the access point network name. Default network name is “INTERMEC.” The access point may not be communicating with the server. Ensure the access point is turned on, properly configured, and has 802.1x security enabled. Troubleshoot 802.
Chapter 8 — Troubleshoot and Maintain the Computer Check 802.11 Network Status If you have trouble connecting to your 802.11 wireless network: • Make sure you have correctly set network parameters on the computer. • Check your wireless security settings. Follow the next procedure to verify available access points and networks, check signal strength, and view other diagnostics.
Chapter 8 — Troubleshoot and Maintain the Computer c Tap Ping. The graph shows the amount of time it takes for the host to return the ping. Tap List to see this information in a list format. 5 Tap the RSSI tab to view the received signal strength of the host signal. The information box includes the current signal strength, host SSID name, MAC address, data rate, and transmit power. • Tap Mark to place an arrow marker above the graph. 6 Tap the Conf tab to set up a log file that lists RSSI history.
Chapter 8 — Troubleshoot and Maintain the Computer Problem Solution When you release a Scan button The Good Read light will remain on if you configure the or handle trigger, the Good Read computer to use continuous/edge triggering. If you configure light does not turn off. the computer for level triggering and the Good Read light remains on, there may be a problem. Press one of the Scan buttons or pull the trigger again without scanning a bar code label.
Chapter 8 — Troubleshoot and Maintain the Computer Use ScanDiagnostic to Troubleshoot the Scanner Use the ScanDiagnostic application to troubleshoot problems such as the inability to read a bar code or a scanner that does not turn on. 1 From the Home menu, tap Start > ScanDiagnostic. 2 From the Scan Health screen, select the scanner you want to troubleshoot and then tap Diagnose. The application checks to make sure the scanner is enabled and checks settings to make sure they are optimized.
Chapter 8 — Troubleshoot and Maintain the Computer Problem Solution The computer appears to be locked up and you cannot enter data. • Press the Power button and select Suspend from the Power Options menu. Press the Power button to turn the screen back on. • Press the Power button and select Reboot from the Power Options menu. • Remove the battery and press the Reset button to perform a cold boot. For help, see “Cold Boot the Computer” on page 123. • Try reloading the firmware.
Chapter 8 — Troubleshoot and Maintain the Computer Call Product Support If you cannot find the answer to your problem in the “Troubleshooting the Computer” section, you can visit the Intermec technical knowledge base (Knowledge Central) at intermec.custhelp.com to review technical information or to request technical support. If you still need help after visiting Knowledge Central, you may need to call Product Support.
Chapter 8 — Troubleshoot and Maintain the Computer Find Your Operating System Version Use the following procedure to find the OS version of your mobile computer. 1 Press the Intermec Dashboard (m) button to launch the Dashboard. 2 Tap the Information bar. The Information Details page appears and displays information such as the firmware version and the OS version.
Chapter 8 — Troubleshoot and Maintain the Computer Note: Cold booting the computer does not guarantee that cached disk data will be saved, so transactional data may be lost during the reset. All other data, such as configuration and network settings, is preserved. 1 Press the Power button to suspend the computer. 2 Remove the handstrap and the battery pack. 3 Press the Reset button in the battery compartment on the back of the computer.
Chapter 8 — Troubleshoot and Maintain the Computer Clean Boot the Computer A clean boot erases the memory in the mobile computer, including all applications and data files, with the exception of those found in the Flash File Store, or any removable storage. If the computer seems to be locked up, try cold booting it. If this process does not work, use a clean boot to get the computer up and running for further troubleshooting. You can perform a clean boot using the mobile computer.
Chapter 8 — Troubleshoot and Maintain the Computer 1 Press the Power button and choose to suspend the computer. 2 Dip a clean cloth towel in the ammonia solution and wring out the excess. 3 Wipe off the imager window, camera lens, and flash area. Do not allow any abrasive material to touch these surfaces. 4 Wipe dry.
A Specifications and Default Settings 127
Appendix A — Specifications and Default Settings Physical and Environmental Specifications CN70 Physical Dimensions Dimensions 16.9 x 8.0 x 3.4 cm (6.66 x 3.14 x 1.35 in) Weight 450 g (15.2 oz) with battery CN70e Physical Dimensions Dimensions 19.5 x 8.0 x 3.4 cm (7.66 x 3.14 x 1.35 in) Weight 491 g (16.6 oz) with battery CK70 Physical Dimensions Dimensions 23.7 x 8.0 x 4.3 cm (9.33 x 3.16 x 1.69 in) Weight 562 g (19 oz) with battery CK71 Physical Dimensions Dimensions 23.7 x 8.0 x 5.0 cm (9.33 x 3.
Appendix A — Specifications and Default Settings Power and Electrical Specifications Battery type Rechargeable Lithium-ion (Li-ion) battery Battery capacity CN70/CN70e: 3.7 V, 4000 mAh (14.8 Wh) CK70/CK71: 3.7 V, 5200 mAh (19.2 Wh) Electrical rating x 4.37/4.8 V; 2/1,5 A 70 Series Non-Incendive Computer Specifications The 70 Series mobile computers with non-incendive (NI) certification comply with the following specifications for North America and Canada regions only.
Appendix A — Specifications and Default Settings Hardware Main processor options TI OMAP3, 1 GHz TI OMAP3, 600 MHz Memory 512 MB RAM Persistent storage 1 GB Flash Removable storage up to 32 GB user-accessible microSD card slot Keypad CN70: QWERTY, Numeric CN70e: QWERTY Numeric, Numeric, Calculator-style CK70: Large Alpha, Alphanumeric CK71: Numeric Function, Alphanumeric Imaging options 5 megapixel color camera and EA30 area imager (all), EV12 (CK71 only), or EX25 (CK71 only) Back Accessory Inter
Appendix A — Specifications and Default Settings Standard Communications • • • • • • • • UMTS (not available on CK71) CDMA (not available on CK71) Flexible Network Radio (not available on CK71) GPS (not available on CK71) 802.11a/b/g/n Bluetooth USB Full Speed V2.0 Host USB Full Speed V2.0 Client Wireless LAN Standards compliant IEEE 802.11a/b/g/n (2.4 GHz and 5 GHz), Single Stream Data rates up to 72Mbps Security 802.11i, WPA, WPA2, 802.
Appendix A — Specifications and Default Settings Bar Code Symbologies The imagers support all of the bar code symbologies listed in the next table.
Appendix A — Specifications and Default Settings Imager Reading Distances Typical reading distances are done in an office environment using office lights (4 lux). Minimum distances are measured in the dark (0 lux). Both reading distances are provided in respective scan engine integration guides. Contact your local Intermec representative for more information. Below are the typical and minimum standard reading distances for the 70 Series computer built with an EA30 imager.
Appendix A — Specifications and Default Settings EA30 Typical Reading Distances - Extended Reading Range These typical reading distances are measured in an office environment (250 lux) for the EA30 standard model with Extended Reading Range activated. Extended Reading Range is enabled by default. EA30 Typical Reading Distances - Extended Reading Range Activated 0" 4" 8" 12" 16" 20" 24" 28" 32" 36" 40" in 12" 30 8" 20 4" 10 0" 0 4" 10 0.125mm/5 mils EAN/UPC 8" 20 0.
Appendix A — Specifications and Default Settings EA30 Area Imager Minimum Reading Distances Minimum distances are measured in the dark (0 lux). 0" 4" 8" 12" 16" 20" 24" 28" in 12" 30 Data Matrix 10 mils 8" 20 PDF417 10 mils 4" 10 0" 0 4" 10 0.125mm/5 mils EAN/UPC 8" 20 0.5 mm / 20 mils 12" 30 1 mm / 40 mils cm 0 10 20 30 40 50 60 70 EA30 Minimum Reading Distances Symbology Density Minimum Distance Maximum Distance Code 39 0.1 mm (4 mils) 0.1250 mm (5 mils) 0.
Appendix A — Specifications and Default Settings EA30 Area Imager Typical Reading Distances Typical distances are measured in an office environment (250 lux). 0" 4" 8" 12" 16" 20" 24" 28" 32" 36" in 12" 30 Data Matrix 10 mils 8" 20 PDF417 10 mils 4" 10 0" 0 4" 10 0.125mm/5 mils EAN/UPC 8" 20 0.5 mm / 20 mils 12" 30 1 mm / 40 mils cm 0 10 20 30 40 50 60 70 80 90 EA30 Typical Reading Distances Symbology Density Minimum Distance Maximum Distance Code 39 0.
Appendix A — Specifications and Default Settings EV12 Linear Imager Minimum Reading Distances The illustration below does not include the 0.12 cm (0.05 in) setback for the CK71. Minimum reading distances are measured in the dark (0 lux). 0" in 2" 4" 8" 6" 10" 12" 14" 16" 8" 20 7" 6" 15 EAN/UPC 100% 5" 4" 10 3" 5 2" 1" 0 0" 1" 5 2" 3" 0.125 mm / 5 mils 10 4" 0.25 mm / 10 mils 5" 6" 15 0.
Appendix A — Specifications and Default Settings EV12 LInear Imager Typical Reading Distances The illustration below does not include the 0.12 cm (0.05 in) setback for the CK71. Typical reading distances are measured in an office environment (200 lux). 0" in 4" 8" 12" 16" 20" 24" 28" 32" 36" 16" 40 14" 12" 30 10" EAN/UPC 100% 8" 20 6" 10 4" 2" 0 0" 2" 10 4" 6" 0.125 mm / 5 mils 20 8" 0.25 mm / 10 mils 10" 12" 30 0.
Appendix A — Specifications and Default Settings EX25 Near-Far Range Imager Minimum Reading Distance Minimum reading distances are measured in the dark (0 lux). The following graphic does not include the 0.24 cm (0.09 in) setback for the CK71. 0” 16” 32” 48” 64” 80” 96” 128” 112” 144” 160” 176” in 80” 200 64” 160 100% EAN contrast UPC 48” 120 32” 80 16” 40 0” 0 16” 40 32” 80 0.25 mm/10 mils 48” 120 0.5 mm/20 mils 1 mm/40 mils 64” 160 1.
Appendix A — Specifications and Default Settings EX25 Near-Far Range Imager Typical Reading Distance Typical reading distances are measured in an office environment (200 lux). The following graphics do not include the 0.24 cm (0.09 in) setback for the CK71. EX25 Near-Far Range Imager 1D Typical Reading Distances in 0” 40” 80” 120” 160” 200” 240” 280” 320” 360” 400” 440” 480” 160” 400 128” 320 100% EAN contrast UPC 96” 240 64” 160 32” 80 0” 0 32” 80 0.25 mm 10 mils 160 64” 0.
Appendix A — Specifications and Default Settings EX25 1D Symbologies Typical Reading Distances With 0.24 cm (0.09 in) Setback Symbology Density Minimum Distance Maximum Distance Code 39 0.25 mm (10 mils) 0.5 mm (20 mils) 1 mm (40 mils) 1.4 mm (55 mils) 2.5 mm (100 mils) 15 cm (5.91 in) 16 cm (6.30 in) 25 cm (9.84 in) 40 cm (15.75 in) ** 135 cm (53.15 in) 280 cm (110.24 in) 550 cm (216.54 in) 720 cm (283.46 in) 1200 cm (472.44 in) Code 128 retro-reflective 2.5 mm (100 mils) ** 1300 cm (511.
Appendix A — Specifications and Default Settings EX25 2D Symbologies Typical Reading Distances With 0.24 cm (0.09 in) Setback Symbology Density Minimum Distance Maximum Distance DataMatrix 0.25 mm (10 mils) 0.76 mm (30 mils) 1.4 mm (55 mils) 2.5 mm (100 mils) 7.5 mm (300 mils) 15 cm (5.91 in) 25 cm (9.84 in) ** ** 20 cm (7.87 in) 90 cm (35.43 in) 310 cm (122.05 in) 450 cm (177.17 in) 1100 cm (433.07 in) 1524 cm (600 in) ** Minimum distance depends on bar code width and scan angle.
Appendix A — Specifications and Default Settings Symbology Settings Symbology Default Value AustraliaPost Disable Aztec Disable BPO Disable CanadaPost Disable Codabar Disable Codablock A Disable Codablock F Disable Code 11 Disable Code 39 Enable Code 93 Disable Code 128/GS1-128 Enable DataMatrix Enable DutchPost Disable EAN/UPC Enable UPC A, UPC E, EAN 8, EAN 13 GS1 Composite Disable GS1 DataBar Expanded Disable GS1 DataBar Limited Disable GS1 DataBar Omni-Directional D
Appendix A — Specifications and Default Settings Symbology Default Value Standard 2 of 5 Disable SwedenPost Disable Telepen Disable TLC 39 Disable Symbology Option Settings Symbology Option Settings Default Value Preamble None (Disabled) Postamble None (Disabled) Symbology Identifier Disable Multicode Disable Scanner Settings Scanner Settings Default Value Trigger Predefined Modes Level Trigger Mode Level Aimer Mode Typical aimer Hardware Trigger Enable Trigger Timeout (sec) 2
Appendix A — Specifications and Default Settings Imager Settings Default Value Image Capture Output Compression Output Compression Quality Edge Enhancement Noise Reduction Subsampling Image Rotation Image Lighting Correction Bitmap 0 None 0 None None Disable Decode Security Settings Decode Security Settings Default Value Consecutive Data Validation 0 Identical Consecutive Timeout 300 ms Different Consecutive Timeout 0 Center Decoding Disable Center Decoding Tolerance 0 Communications Use com
Appendix A — Specifications and Default Settings 802.11 Radio Setting Default Value Import User Certificates False Import Pac Files False Radio Bands b/g (2.
Appendix A — Specifications and Default Settings Good Read Settings Good Read Setting Default Value Internal Scanner Good Read Beep Tethered Scanner Bluetooth Scanner Good Read Beep One Beep One Beep One Beep Backlight Settings Backlight Setting Default Value Display Backlight Adjustment Keypad Backlight Light Level Normal On Based on Light Level Low Screen Settings Screen Setting Default Value Screen Rotations Screen Rotation Sensor Portrait 0 Degrees Disabled Sound Settings Sound Setting Def
Appendix A — Specifications and Default Settings Power Management Settings Power Management Setting Default Value Enable Power Button Screen Screen Options Displayed On Hibernate, Suspend, Reboot Screen Timeout (Seconds) 5 Power Button Behavior Suspend Device Turns Off After (Battery Power) 5 minutes Screen Turns Off After (Battery Power) Disabled Device Turns Off After (External Power) Disabled Screen Turns Off After (External Power) Disabled Device Off Sensor Disabled Profiles Settings Application Pr
Appendix A — Specifications and Default Settings GPS Settings Use GPS settings to configure how the mobile computer communicates with the GPS network. GPS GPS Setting Default Value Enable Bread Crumbing Disable Core Messaging Service Settings Use core messaging service settings to configure the message routers between client and server software applications.
Appendix A — Specifications and Default Settings Device Health Screen Captures Device Health Screen Captures Setting Default Value Directory \SmartSystems\ScreenCapture Screen Captures Allowed 3 Device Wipe Device Wipe Setting Default Value Enable Wipe Disabled Interval (in days) Null Virtual Wedge Settings Use virtual wedge settings to configure the virtual wedge.
B Keypads and Keystrokes 151
Appendix B — Keypads and Keystrokes Standard Characters Use the following tables to learn how to enter standard and other available characters and functions with the keypad. If there is no sequence of keystrokes for a particular character or function, it is only available through the soft input panel (SIP), which you can access by tapping the keyboard icon on the touch screen. Note: You can only enter “*” and “#” characters in the phone or contacts applications.
Appendix B — Keypads and Keystrokes Character Numeric Keypad QWERTY Keypad n c66 c666 c7 c77 c777 c7777 c8 c88 c888 c9 c99 c999 c9999 c12 c122 c1222 c13 c133 c1333 c14 c144 N O P Q R S T U V W X Y Z yA yB yC yD yE yF yG yH o p q r s t u v w x y z A B C D E F G H 70 Series Mobile Computer User Manual 153
Appendix B — Keypads and Keystrokes Character Numeric Keypad QWERTY Keypad I c1444 c15 c155 c1555 c16 c166 c1666 c17 c177 c1777 c17777 c18 c188 c1888 c19 c199 c1999 c19999 0 1 2 yI yJ yK yL yM yN yO yP yQ yR yS yT yU yV yW yX yY yZ b, bY bU J K L M N O P Q R S T U V W X Y Z 0 1 2 154 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Numeric Keypad QWERTY Keypad 3 3 4 5 6 7 8 9 bI bH bJ bK bB bN bM 4 5 6 7 8 9 CN70 Characters and Functions To Enter Numeric Keypad QWERTY Keypad @ (at symbol) N/A & (ampersand) N/A * (asterisk) * : (colon) N/A , (comma) N/A $ (dollar) N/A ! (exclamation) N/A - (hyphen) - % (percent) N/A . (period) . b# bQ bS bC bD bX bE bO bG bR .
Appendix B — Keypads and Keystrokes To Enter Numeric Keypad QWERTY Keypad ? (question mark) N/A ‘ (apostrophe) N/A Forward Tab j { u d l r c1 e b| b or c c0 b m or c m | p w m bA bZ j { u d l r yy e bP b or y s bm | p w m Backspace Up Arrow Down Arrow Left Arrow Right Arrow CapsLock Enter ok Shift Space Start (Windows) Esc Talk End Call Intermec Dashboard 156 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes CN70e Keypads and Keystrokes CN70e Alphanumeric Characters Character Numeric Keypad a b c d e f g h i j k l m n o p q r s c2 c22 c222 c3 c33 c333 c4 c44 c444 c5 c55 c555 c6 c66 c666 c7 c77 c777 c7777 70 Series Mobile Computer User Manual Calculator-Style Keypad QWERTY Numeric Keypad c8 c88 c888 c9 c99 c999 c4 c44 c444 c5 c55 c555 c6 c66 c666 c1 c11 c111 c1111 A B C D E F G H I J K L M N O P Q R S 157
Appendix B — Keypads and Keystrokes Character Numeric Keypad t u v w x y z A B C D E F G H I J K L M N 158 c8 c88 c888 c9 c99 c999 c9999 c12 c122 c1222 c13 c133 c1333 c14 c144 c1444 c15 c155 c1555 c16 c166 Calculator-Style Keypad QWERTY Numeric Keypad c2 c22 c222 c3 c33 c333 c3333 c78 c788 c7888 c79 c799 c7999 c74 c744 c7444 c75 c755 c7555 c76 c766 T U V W X Y Z yA yB yC yD yE yF yG yH yI yJ yK yL yM yN 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Numeric Keypad O P Q R S T U V W X Y Z 0 1 2 3 4 5 6 c1666 c17 c177 c1777 c1777 7 c18 c188 c1888 c19 c199 c1999 c1999 9 0 1 2 3 4 5 6 70 Series Mobile Computer User Manual Calculator-Style Keypad QWERTY Numeric Keypad c7666 c71 c711 c7111 c7111 1 c72 c722 c7222 c73 c733 c7333 c7333 3 0 1 2 3 4 5 6 yO yP yQ yR yS yT yU yV yW yX yY yZ 0 1 2 3 4 5 6 159
Appendix B — Keypads and Keystrokes Character Numeric Keypad 7 8 9 7 8 9 Calculator-Style Keypad QWERTY Numeric Keypad 7 8 9 7 8 9 CN70e Characters and Functions To Enter Numeric Keypad Calculator-Style Keypad @ (at symbol) N/A N/A & (ampersand) N/A N/A * (asterisk) * * : (colon) N/A N/A , (comma) N/A N/A $ (dollar) N/A N/A ! (exclamation) N/A N/A - (hyphen) - - % (percent) N/A N/A . (period) . b# .
Appendix B — Keypads and Keystrokes To Enter Numeric Keypad Calculator-Style Keypad QWERTY Numeric Keypad Up Arrow u d l r c1 e b| b or c c0 b m or c m | p w m u d l r c7 e b| b or c c0 b m or c m | p w m u d l r yy e b| b or y s bm | p w m Down Arrow Left Arrow Right Arrow CapsLock Enter ok Shift Space Start (Windows) Esc Talk End Call Intermec Dashboard CK70 Keypads and Keystrokes CK70 Alphanumeric Characters Character Large Alpha Keypad Alphanumeric Keypad a A B C A B C b c 70 Series Mob
Appendix B — Keypads and Keystrokes Character Large Alpha Keypad Alphanumeric Keypad d D E F G H I J K L M N O P Q R S T U V W X D E F G H I J K L M N O P Q R S T U V W X e f g h i j k l m n o p q r s t u v w x 162 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Large Alpha Keypad Alphanumeric Keypad y Y Z yA yB yC yD yE yF yG yH yI yJ yK yL yM yN yO yP yQ yR yS Y Z yA yB yC yD yE yF yG yH yI yJ yK yL yM yN yO yP yQ yR yS z A B C D E F G H I J K L M N O P Q R S 70 Series Mobile Computer User Manual 163
Appendix B — Keypads and Keystrokes Character Large Alpha Keypad Alphanumeric Keypad T yT yU yV yW yX yY yZ bP bD bE bF bG bH bI bK bL bM yT yU yV yW yX yY yZ 0 1 2 3 4 5 6 7 8 9 U V W X Y Z 0 1 2 3 4 5 6 7 8 9 CK70 Characters and Functions To Enter Large Alpha Keypad Alphanumeric Keypad @ (at symbol) bS bW N/A & (ampersand) 164 bU 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes To Enter Large Alpha Keypad Alphanumeric Keypad * (asterisk) bO bJ cJ bT cS cW cX cO . bX bQ cQ cT bY cY cN bN bV cV b0 b2 b5 cX : (colon) ; (semicolon) , (comma) $ (dollar) ! (exclamation) - (hyphen or minus) % (percent) .
Appendix B — Keypads and Keystrokes To Enter Large Alpha Keypad Alphanumeric Keypad ~ (tilde) N/A \ (backslash) cU bU bW c8 b8 bZ / (forward slash) “ (quotes) N/A ( (left parenthesis) bR cR bZ cZ bs ) (right parenthesis) Insert Delete Sym ¦ (broken vertical bar) ̀ (grave) Forward Tab Backspace Up Arrow Down Arrow Left Arrow Right Arrow CapsLock Enter ok Shift 166 N/A N/A j { u d l r yy e cm y N/A N/A b4 b6 N/A cS cW j { u d l r yy e cm y 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes To Enter Large Alpha Keypad Alphanumeric Keypad Space s b m or c m | s b m or c m | Alt N/A Alt Ctrl Ctrl Ctrl Send Call bA bC m c1 c3 m To Enter Large Alpha Keypad Alphanumeric Keypad F1 cD cE cF cG cH cI cK cL cM cP ¡ ¢ £ ¤ ¥ b¡ b¢ b£ b¤ b¥ bA bB Start (Windows) Esc End Call Intermec Dashboard CK70 Function Keys F2 F3 F4 F5 F6 F7 F8 F9 F10 F11 F12 N/A N/A 70 Series Mobile Computer User Manual 167
Appendix B — Keypads and Keystrokes To Enter Large Alpha Keypad F13 Alphanumeric Keypad bC bD bE bF bG bH bI bJ bK bL bM bN N/A F14 N/A F15 N/A F16 N/A F17 N/A F18 N/A F19 N/A F20 N/A F21 N/A F22 N/A F23 N/A F24 N/A CK71 Keypads and Keystrokes CK71 Alphanumeric Characters Character Numeric With Function Keys Keypad Alphanumeric Keypad a b7 b8 b9 b4 b5 b6 A B C D E F b c d e f 168 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Numeric With Function Keys Keypad Alphanumeric Keypad g b1 b2 b3 b0 bb¡ b¢ b£ b¤ b¥ b¦ b§ b¨ b© bª b« b¬ bm b Ctrl b Alt by7 G H I J K L M N O P Q R S T U V W X Y Z yA h i j k l m n o p q r s t u v w x y z A 70 Series Mobile Computer User Manual 169
Appendix B — Keypads and Keystrokes Character Numeric With Function Keys Keypad Alphanumeric Keypad B by8 by9 by4 by5 by6 by1 by2 by3 by0 byby¡ by¢ by£ by¤ by¥ by¦ by§ by¨ by© byª by« yB yC yD yE yF yG yH yI yJ yK yL yM yN yO yP yQ yR yS yT yU yV C D E F G H I J K L M N O P Q R S T U V 170 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes Character Numeric With Function Keys Keypad Alphanumeric Keypad W by¬ bym b y Ctrl b y Alt 0 1 2 3 4 5 6 7 8 9 yW yX yY yZ 0 1 2 3 4 5 6 7 8 9 X Y Z 0 1 2 3 4 5 6 7 8 9 CK71 Characters and Functions To Enter Numeric With Function Keys Keypad Alphanumeric Keypad : (colon) cs ; (semicolon) N/A b8 b5 cX , (comma) $ (dollar) ! (exclamation) N/A cS cW 70 Series Mobile Computer User Manual N/A N/A 171
Appendix B — Keypads and Keystrokes To Enter Numeric With Function Keys Keypad Alphanumeric Keypad - (hyphen or minus) . cs . bs bY bS cX cV bV bT cT bU cU bW c2 b2 bZ b4 b6 cS cW j . (period) + (plus) ‘ (apostrophe) = (equals) _ (underscore) > (greater than) < (less than) [ (left square bracket) ] (right square bracket) N/A N/A N/A cN/A N/A N/A N/A { (left curly brace) N/A } (right curly brace) N/A ~ (tilde) N/A \ (backslash) c Alt c Ctrl / (forward slash) “ (quotes) N/A Insert bl c4 D
Appendix B — Keypads and Keystrokes To Enter Numeric With Function Keys Keypad Alphanumeric Keypad Backspace { u d l r yy e cm y s b m or c m | { u d l r yy e cm y s b m or c m | b| Up Arrow Down Arrow Left Arrow Right Arrow CapsLock Enter ok Shift Space Start (Windows) Esc Alt Alt Ctrl Ctrl Ctrl Intermec Dashboard m m To Enter Numeric With Function Keys Keypad Alphanumeric Keypad F1 ¡ ¢ £ ¤ ¡ ¢ £ ¤ CK71 Function Keys F2 F3 F4 70 Series Mobile Computer User Manual 173
Appendix B — Keypads and Keystrokes To Enter Numeric With Function Keys Keypad Alphanumeric Keypad F5 ¥ ¦ § ¨ © ª « ¬ c¡ c¢ c£ c¤ c¥ c¦ c§ c¨ c© cª c« c¬ ¥ b¡ b¢ b£ b¤ b¥ bA bB bC bD bE bF bG bH bI bJ bK bL bM bN F6 F7 F8 F9 F10 F11 F12 F13 F14 F15 F16 F17 F18 F19 F20 F21 F22 F23 F24 174 70 Series Mobile Computer User Manual
Appendix B — Keypads and Keystrokes CK71 Intermec Terminal Emulation (ITE) Keys To Enter Numeric With Function Keys Keypad Alphanumeric Keypad Attention c0 Autolog N/A Clear b6 Duplicate N/A EEOF N/A Erase N/A cA c¤ c6 cD c¥ cE cF c1 c1 cG b3 cI cH cK cM cO cN b9 c¡ c¢ Find Field + Field Fieldmark Help Hex Home Keypad Menu Mode New Line Next Screen PA1 PA2 N/A cx bx N/A N/A N/A c.
Appendix B — Keypads and Keystrokes To Enter Numeric With Function Keys Keypad Alphanumeric Keypad PA3 c3 cd c£ cd cP c7 cR c| ce c5 c8 cQ bd Page Print N/A Previous Screen c7 Remove N/A Reset c| ce c5 c8 br Return Roll Down Roll Up System Request View View Down View Up 176 N/A bd bu N/A N/A 70 Series Mobile Computer User Manual
C ScanNGo Wi-Fi Configuration Bar Codes You can use the ScanNGo Wi-Fi configuration bar codes to quickly configure the 802.11 radio in your computer.
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes Radio Configuration Bar Codes Use the following ScanNGo bar codes to enable the 802.11 radio and set the defaults for either Funk or Microsoft Wireless Zero Configuration security. After you scan the bar codes, you will still need to use Intermec Settings or another configuration program to set network-specific settings on your computer and to configure the wireless security. The CN70, CN70e, and CK70 are available with the EA30 imager only.
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes 2D Imager Radio Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Funk defaults 1D Configuration Bar Codes You can configure the computer with a 1D imager (EV12). 1 Scan the START HERE bar code from the table and wait for the program to start. 2 Scan the 1/9 bar code. 3 Scan the rest of the bar codes in any order.
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes 1D Imager Radio Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Funk defaults 180 70 Series Mobile Computer User Manual
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Funk defaults 70 Series Mobile Computer User Manual 181
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Microsoft WZC defaults 182 70 Series Mobile Computer User Manual
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes When You Want To: Scan This Bar Code • Set all communication settings to defaults (Wi-Fi, WWAN if applicable) • Enable Wi-Fi - set Microsoft WZC defaults 70 Series Mobile Computer User Manual 183
Appendix C — ScanNGo Wi-Fi Configuration Bar Codes 184 70 Series Mobile Computer User Manual
I Index 185
Index Symbols .cab files, using to install applications 108 Numerics 70 Series computer models 2 features 5 802.11 communications, configuring 83 802.11 network status, troubleshooting 117 802.11 radio, default settings 145 802.
Index CDMA phone activating 54 carriers 54 certificate, loading 102 changing the battery 11 characters entering on CK70/CK71 keypad 24 entering on numeric keypad 23 entering on QWERTY keypad 23 entering with keystrokes 152– 176 charging accessories 11 charging the battery 11 CK70 keypads, illustrated 19, 20 keystrokes, listed 161–168 status LEDs 6, 7 CK70/CK71 battery, described 8 entering characters on keypad 24 magstripe reader adapter, described 8 CK71 keypads, illustrated 21, 22 keystrokes, listed 168–1
Index files, transferring to and from PC 36 fix interval, configuring with iGPS 72 flash file store, using computer as 37 flashlight, using 28 flick, screen gesture, described 41 Funk security configuring 802.1x 95 configuring LEAP 96 configuring static WEP 96 configuring WPA Enterprise (802.1x) 93 configuring WPA Personal (PSK) 94 configuring WPA2 Enterprise (802.
Index keypad (continued) keystrokes for entering characters 152–176 troubleshooting keys 121 Knowledge Central website 122 L language provisioning 10 launching applications automatically 110 LEAP, configuring with Funk 96 LEDs battery status, described 14 status, described 7 location, status LEDs 7 locked computer, troubleshooting 121 M magstripe reader adapter, described 8 magstripe reader snap-on adapter, described 8 mass storage device, using computer as 37 memory, computer 130 microSD card about 30 inst
Index product support calling 122 Profile Settings application, described 46 configuring with Intermec Settings 80 profile, choosing Funk security 93 Q QWERTY keypad CN70, illustrated 16 entering characters on 23 illustrated 16 QWERTY numeric keypad CN70e, illustrated 17 R reading distances EA30 area imager 135 EV12 linear imager 137 EX25 imager 139 Ready-to-Work LED described 7 reboot performing 123 power option described 26 recording a video 66 regulatory approvals 131 reset button, location 124 performin
Index Suspend, power option described 26 symbologies, supported 132 system software updating with microSD card 112 updating with SmartSystems Foundation 111 T terminal emulation, troubleshooting 115 tethered scanner, connecting 89 tethered stylus replacement kit, described 9 Tile bar described 40 illustration 40 Title bar described 40 illustration 40 status icon descriptions 42 transferring files, to and from PC 36 troubleshooting 115–119 802.11 network status 117 802.
Index www.intermec.
Worldwide Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.com © 2012 Intermec Technologies Corporation. All rights reserved.
