4 Maintaining the Computer Use this chapter to solve problems you may encounter and perform routine maintenance on your CN3 Mobile Computer: CN3 Mobile Computer User’s Manual - PRELIMINARY 91
Chapter 4 — Maintaining the Computer Upgrading the Operating System on your CN3 Computer You can use the Intermec Recovery Tools CD to reinstall or upgrade the operating system software on the CN3 Computer. For more information, contact your Intermec representative for more information about this CD. You can use the SmartSystems™ Foundation application from Intermec to perform upgrades on your CN3 Computer, versions 2.0 or later.
Chapter 4 — Maintaining the Computer Problems While Operating the CN3 Computer (continued) Problem Solution The CN3 Computer appears to be locked up and you cannot enter data. Press I to turn off the CN3 Computer, then press I again to turn on the CN3 Computer. Press and hold I for ten seconds to clean-boot the CN3 Computer. Try reloading the firmware. See “Updating the System Software” on page 73. If the CN3 Computer does not boot or reset, contact your local Intermec representative for help.
Chapter 4 — Maintaining the Computer Problems with Wireless Connectivity (continued) Problem Solution The CN3 Computer is connected to the Intermec Application Server or host computer and you move to a new site to collect data. The Network Connection icon was visible, but is now replaced with the No Network Connection icon. Move closer to an access point or to a different location to reestablish communications until the Network Connection icon appears.
Chapter 4 — Maintaining the Computer Problem Solution A network connection icon appears in the toolbar, but then disappears. CN3 Computer may not be communicating with the intended access point. Ensure the CN3 network name matches the access point network name. Default network name is “INTERMEC.” Access point may not be communicating with server. Ensure the access point is turned on, properly configured, and has 802.1x security enabled. The CN3 Computer indicates it is not authenticated.
Chapter 4 — Maintaining the Computer Problems While Scanning Bar Codes (continued) Problem Solution The input device attached to the CN3 Computer does not work well or read bar code labels very quickly. Set the Scanner Model command to the specific attached input device. Check enabled bar code symbologies and enable only the symbologies being used. The scanner will not read the bar code label. Aim the scanner beam to cross entire bar code label in one pass. Vary the scanning angle.
Chapter 4 — Maintaining the Computer Cleaning the Scanner and Camera Windows and Screen To keep the CN3 Computer in good working order, you may need to clean the EA11 scanner and color camera windows and the screen. Clean the scanner and camera windows and screen as often as needed for the environment in which you are using the CN3 Computer. To clean the CN3 Computer, use a solution of ammonia and water. There are no user-serviceable parts inside the CN3 Computer.
Chapter 4 — Maintaining the Computer 98 PRELIMINARY - CN3 Mobile Computer User’s Manual
5 Network Support This chapter includes information about the different networks supported by the CN3 Mobile Computer, and ways to configure and manage those networks. Note that the CN3 Computer automatically installs the appropriate software for radio or phone use when the unit is turned on. Note: Desktop icons and applet icons are shown to the left. Any place that Start is mentioned, tap the following Windows icon in the top, left corner of your CN3 desktop.
Chapter 5 — Network Support Personal Area Networks “Bluetooth” is the name given to a technology standard using short-range radio links, intended to replace cables connecting portable and fixed electronic devices. The standard defines a uniform structure for a range of devices to communicate with each other with minimal user effort. Its key features are robustness, low complexity, low power, and low cost.
Chapter 5 — Network Support Bluetooth Bluetooth is not started by default after a clean-boot is performed. To run Bluetooth, tap Start > Settings > the Connections tab > the Bluetooth icon. The CN3 Computer retains the Bluetooth state when clean-boots are performed, for example: • If Bluetooth is enabled, and a clean-boot was performed, the CN3 Computer boots up with the Bluetooth state enabled and Bluetooth virtual COM ports (such as printing) registered.
Chapter 5 — Network Support 2 When the CN3 Computer is finished scanning, any newly discovered devices appear in the box. Tap Refresh to do additional discoveries. 3 Select a device to which to connect, then click Next. 4 Enter a passkey to establish a secure connection, then tap Next. Tap Yes if prompted to let the other device connect with your CN3 Computer.
Chapter 5 — Network Support 5 Select what services you want from this remote device, then click Finish to return to the Devices tab. COM Ports Use this page to connect to other devices or allow other devices to connect with your CN3 Computer. 1 Tap New Outgoing Port to connection to a Bluetooth device, select the device to add, then click Next.
Chapter 5 — Network Support 2 Select a port from the Port drop-down list, check Secure Connection, then click Finish to return to the COM Ports page. 3 Tap New Incoming Port to allow other Bluetooth devices to connect with your CN3 Computer, select on which port to secure this connection, then click Finish to return to the COM Ports page. 4 You can press and hold on a device to either edit that device or delete it from the list.
Chapter 5 — Network Support Wireless Printing The Wireless Printing applet separates the task of wireless printing from other Bluetooth management items not relevant to this task. Wireless Printing has a concept of the “current wireless printer.” This printer is the one to which the CN3 Computer makes a connection when the wireless printing COM port is opened. If there is no current wireless printer, there is no wireless printing COM port.
Chapter 5 — Network Support 3 In about half a minute, Bluetooth devices discovered within your range will appear. If your preferred printer is in the list, select to highlight the printer, then tap OK. If you do not see your preferred device, make sure this device is powered on and set to discovery, then tap Search again. Tap Cancel to return to the first screen without making changes.
Chapter 5 — Network Support Set Different Printer To change your printer, do the following: 1 Select Start > Settings > the System tab > the Wireless Printing icon. 2 Tap Set Different Printer to return to the device discovery screen. 3 Tap either Search or Manual, tap OK., then do the applicable steps. Tap Cancel to the current wireless printer settings without making changes, then tap Exit to close the applet.
Chapter 5 — Network Support Discovering Bluetooth Headsets To discover a Bluetooth headset with either a “headset” or a “hands-free” profile, tap Search for devices. Discovered audio devices are added to the list with an icon to identify either profile. Connecting to a Bluetooth Headset Note: You can only select one Bluetooth audio device. 1 Tap a Bluetooth audio device from the list of discovered devices.
Chapter 5 — Network Support 2 Tap the device name, then select Connect from the pop-up menu. On successful device activation, the device icon changes to remove the red bar from the left connection image. Red bar cleared from connection image • Tap the Volume slider bar to adjust the volume of the connected Bluetooth audio device. • Tap the Microphone slider bar to adjust the microphone gain of the connected Bluetooth audio device.
Chapter 5 — Network Support Connecting with Bluetooth Note: While these instructions apply to many Bluetooth devices, these instructions use the Nokia 3650 for example purposes. Make sure Bluetooth is enabled on your mobile phone. For example, with the Nokia 3650, go to its menu, select Connect > Bluetooth, then set My phone’s visibility to “Shown to all.” Before you connect to the network, make sure Bluetooth is enabled on your CN3 Computer so you can discover and connect to remote devices.
Chapter 5 — Network Support 3 Tap Add new device... if the phone is not listed in the known devices. Make sure your Bluetooth device is turned on before you start the search. 4 When the discovery of devices is complete, select your Bluetooth device, then tap Next to continue. 5 Enter the correct Passkey on both the Bluetooth device and the CN3 Computer, then tap Next to continue.
Chapter 5 — Network Support 6 Enter a name for the device if needed, or select what services to use, then tap Finish. 7 Select the Bluetooth device to use to connect to the network, then tap Next to continue. 8 Enter the appropriate number as it should be dialed for your Bluetooth connection, then tap Next to continue.
Chapter 5 — Network Support 9 Enter the user name, password, and domain required for your Bluetooth device, then tap Finish. Now you can establish a connection to your network via the Internet Explorer application. To disconnect, tap the Connectivity icon in the top menu bar, then select Disconnect. Local Area Networks The CN3 Computer is a versatile mobile computer that you can add to your wired or wireless data collection network. You can connect your CN3 Computer to your network using either the 802.
Chapter 5 — Network Support Phone Application (GPRS/GSM Radios) With the WAN radio module installed in your CN3 Computer, you can send and receive telephone calls within your Wi-Fi range. Use the speaker on the back of the computer as your earpiece and use the connector on the bottom of the computer for your mouthpiece. Tap Start > Settings > the Phone desktop icon from the Personal tab or tap Start > Phone to access the application which processes your phone calls.
Chapter 5 — Network Support Phone Application Tap the appropriate keys to enter a telephone number, then tap Talk to dial the number. Tap this to backspace one digit. Tap this to view your previous calls. Tap this to select a previously dialed number. Tap this to dial the phone number shown above the keypad. Tap this toggle the mute option. Tap this to access the Contacts application. Tap this to access the Notes application.
Chapter 5 — Network Support more information about the Contacts application. Tools Tap Tools > Send SMS tab to access the Inbox application and send an SMS (Short Messaging Service) message. Be sure to have an SMS number ready to send the message — this is usually the mobile phone number. See “Messaging: Sending and Receiving E-mail Messages” on page 56 for information about Messaging.
Chapter 5 — Network Support & Notifications applet. • Tap the Services tab to access settings for any of the provided services.
Chapter 5 — Network Support Tap any of the settings, then tap Get Settings. Make your changes, then tap ok to return to the Settings screen. Below is a sample Settings screen. Tap the Network tab to find, set, or select the type of network on which this phone is to communicate. Remote Access (Modems) You can set up connections to the Internet and corporate network at work to browse the Internet or intranet, send and receive e-mail, and synchronize information using ActiveSync.
Chapter 5 — Network Support vider provides the software needed to install other services, such as paging and fax services. If this is the method you want to use, see “Connecting to an Internet Service Provider” on page 119. • My Work Network: Connect to the network at your company or organization where you work. Once connected, you can send and receive email messages by using Messaging, view Web or WAP pages by using Internet Explorer Mobile, and synchronize with your desktop.
Chapter 5 — Network Support list drop-down, then tap Next to continue. 3 Enter the access phone number, then tap Next. For more information, tap use dialing rules. 4 Enter the user name, password, and domain (if provided by an ISP or your network administrator), then tap Finish. 5 Tap the Advanced tab from the Connections screen, then tap Dialing Rules to specify your current location.
Chapter 5 — Network Support nections. Tap Use dialing rules, tap ok, then tap Edit to continue. 6 Specify your current phone type. If your phone type is pulse dialing, check Pulse dialing. If your type is tone dialing (as most phone lines are), then clear Pulse dialing. Continue to tap ok to close each page and return to the Settings page. To start the connection, start using one of the following programs. Once connected, you can: • Send and receive e-mail messages by using Messaging.
Chapter 5 — Network Support administrator needs to set up a RAS account for you. Your network administrator may also give you Virtual Private Network (VPN) settings. Note: To change modem connection settings in My Work Network, tap Manage existing connections. Select the desired modem connection, tap Settings, then follow the instructions on the screen. To view additional information for any screen in the wizard or while changing settings, tap the Help icon. 1 Tap Start > Settings > the Connections icon.
Chapter 5 — Network Support create dialing rules to avoid creating numerous modem connections for the same phone number. For more information, tap use dialing rules. • Enter the phone number exactly as you want it dialed. For example, if you call from a business complex or hotel that requires a nine before dialing out, enter “9” in front of the phone number. • Enter the APN provided by your mobile phone service provider. • When using dialing rules, phone numbers are entered differently.
Chapter 5 — Network Support Creating a VPN Server Connection to Work A VPN connection helps you to securely connect to servers, such as a corporate network, via the Internet. Ask your network administrator for the following: user name, password, domain name, TCP/IP settings, and host name or IP address of the VPN server To view additional information for any screen in the wizard or while changing settings, tap the Help icon.
Chapter 5 — Network Support 3 Select the type of authentication. If you select A pre-shared key, enter the key provided by your network administrator. 4 Enter your user name, password, and domain name as provided by your ISP or network administrator, then tap Finish. If a domain name was not provided, try the connection without entering a domain name. Insert necessary equipment, such as a network card, into the CN3 Computer, and use a desired program to begin connecting.
Chapter 5 — Network Support iConnect The default network adapter or radio is dependent on what radios are installed in your CN3 Computer. With the iConnect menu, using the Enable feature, you can specify “Wireless” or “No Networking” to load onto your CN3 Computer when a cold-boot is performed. If you had specified a network prior to when a warm-boot is performed on the CN3 Computer, the iConnect application restores your network interfaces to what they were before the warm-boot was performed.
Chapter 5 — Network Support To view information about the Wireless 802.11b/g communications, select Tools > Wireless IP Settings from the iConnect menu for the following: To view the status of the Wireless communications, select Status > Wireless from the iConnect menu to view the status. Tap Try Again to check the status after you make changes to the connection. Ping Test Select Tools > Ping Test from the iConnect menu to test the connection of your CN3 Computer against your network.
Chapter 5 — Network Support Configuring Security Use the next sections to understand how to configure each type of security on your wireless CN3 Computer. The CN3 Computer provides three types of security for your wireless network: Wi-Fi Protected Access 2 (WPA2/802.11i), WPA, and WEP. 802.1x should be referred to as an authentication method used for WPA and WPA2. Another authentication method for WPA and WPA2 would be the Pre-Shared Key (PSK). By default, Funk security is enabled.
Chapter 5 — Network Support Each wireless network is assigned a name (or Service Set Identifier - SSID) to allow multiple networks to exist in the same area without infringement. Intermec recommends using security measures with wireless networks to prevent unauthorized access to your network and to ensure your privacy of transmitted data. Authentication (cryptographically protected) by both the network and the user, transmitted data, and encryption are required elements for secure networks.
Chapter 5 — Network Support Authentication EAP (Extensible Authentication Protocol) 802.11b/g uses this protocol to perform authentication. This is not necessarily an authentication mechanism, but is a common framework for transporting actual authentication protocols. Intermec provides a number of EAP protocols for you to choose the best for your network. EAP-FAST (Flexible Authentication via Secure Tunneling) A publicly accessible IEEE 802.1X EAP type developed by Cisco Systems.
Chapter 5 — Network Support Configuring Funk Security You can define up to four profiles for your Funk Odyssey security. Different profiles let your CN3 Computer communicate in different networks without having to change all of your security settings. For example, you can set up one profile for the manufacturing floor and one for the warehouse. 1 Select Start > Settings > the System tab > the Intermec Settings icon. 2 Tap (+) to expand Communications > 802.11 Radio > Funk Security.
Chapter 5 — Network Support Configuring WPA Security With Funk Security Use this procedure to set WPA security with Funk security. 1 Make sure you have configured the communications and radio parameters on your CN3 Computer and that Funk is your security choice. 2 Open Intermec Settings. Tap (+) to expand Communications > 802.11 Radio > Funk Security > Profile X with “X” being “1” through “4.” 3 For Association, select “WPA” and press Enter.
Chapter 5 — Network Support If you select “LEAP” or “EAP-FAST:” a Select User Name, type your user name, then press Enter. b Select User Password, type a user password, then press Enter. 6 Exit the Intermec Settings applet. Configuring WPA-PSK Security With Funk Security Use this procedure to set WPA-PSK security on your CN3 Computer with Funk security. 1 Make sure you have configured the communications and radio parameters on your CN3 Computer and that Funk is your security choice.
Chapter 5 — Network Support Configuring 802.1x Security With Funk Security Use this procedure to set 802.1x security on your CN3 Computer with Funk security. 1 Make sure you have configured the communications and radio parameters on your CN3 Computer and that Funk is your security choice. 2 Open Intermec Settings. Tap (+) to expand Communications > 802.11 Radio > Funk Security > Profile X with “X” being “1” through “4.” 3 For Association, select “Open” and press Enter.
Chapter 5 — Network Support If you select “LEAP” or “EAP-FAST:” a Select User Name, type your user name, then press Enter. b Select User Password, type a user password, then press Enter. 7 Exit the Intermec Settings applet. Using Static WEP Security The CN3 Computer uses the Wired Equivalent Privacy (WEP) protocol to add security to your wireless network based on the 802.11b/g standard. To use WEP security, you need an access point with an 802.11b/g radio.
Chapter 5 — Network Support A profile contains all the information necessary to authenticate you to the network, such as login name, password or certificate, and protocols by which you are authenticated. You can have up to four profiles for different networks. For example, you may have different login names or passwords on different networks, or you may use a password on one network, and a certificate on another.
Chapter 5 — Network Support Profile Label Enter a unique name for your profile. Network type Tap the list to select “Infrastructure” if the network uses access points to connect to the corporate network or internet; or “Ad-Hoc” to set up a private network with one or more participants. Channel If you select “Ad-Hoc” for the network type, select the channel on which you are communicating with others in your network. There are up to 11 channels available.
Chapter 5 — Network Support 3 Select a data transmission key from the Data TX Key drop-down list near the bottom of this screen. 4 Enter an ASCII key or a hex key either 5 or 13 bytes long based on the radio capability in the appropriate Key # field. Set a 5-byte value for 64bit WEP or a 13-byte value for 128-bit WEP. Precede hex keys with 0x and make sure the keys use 5 or 13 hex pairs. To enable WPA encryption using a pre-shared key: 1 Set 8021x Security as “None.” 2 Set Association to “WPA.
Chapter 5 — Network Support 4 Enter the passphrase as ASCII (12345) in the Pre-Shared Key field. PEAP (Protected EAP) This protocol performs secure authentication against Windows domains and directory services. It is comparable to EAP-TTLS (see page 142), both in its method of operation and its security, though not as flexible. This does not support the range of inside-the-tunnel authentication methods supported by EAP-TTLS. Microsoft and Cisco both support this protocol.
Chapter 5 — Network Support 5 Tap Additional Settings to assign an inner PEAP authentication and set options for server certificate validation and trust. Additional PEAP Settings 1 Select an authentication method from the Inner PEAP Authentication drop-down list. EAP/MS-CHAP-V2 Authenticates against a Windows Domain Controller and other non-Windows user databases. This is Microsoft's implementation of PEAP. EAP/Token Card Use with token cards. The password value entered is never cached.
Chapter 5 — Network Support TLS (EAP-TLS) EAP-TLS is a protocol that is based on the TLS (Transport Layer Security) protocol widely used to secure web sites. This requires both the user and authentication server have certificates for mutual authentication. While cryptically strong, this requires corporations that deploy this to maintain a certificate infrastructure for all their users.
Chapter 5 — Network Support 4 Tap ok to return to the Security page. TTLS (EAP-Tunneled TLS) This protocol provides authentication like EAP-TLS (see page 141) but does not require user certificates. User authentication is done using a password or other credentials that are transported in a securely encrypted “tunnel” established using server certificates. EAP-TTLS works by creating a secure, encrypted tunnel through which you present your credentials to the authentication server.
Chapter 5 — Network Support 5 Tap Additional Settings to assign an inner TTLS authentication and an inner EAP, and set the server certificate validation and trust. Additional TTLS Settings 1 Select an authentication method from the Inner TTLS Authentication drop-down list. PAP Password Authentication Protocol. A simple authentication protocol that sends security information in the clear. CHAP Challenge Handshake Authentication Protocol.
Chapter 5 — Network Support 6 Tap ok to return to the Security page. Get Certificates Certificates are pieces of cryptographic data that guarantee a public key is associated with a private key. They contain a public key and the entity name that owns the key. Each certificate is issued by a certificate authority. Use this page to import a certificate onto the CN3 Computer. Root Certificates 1 Tap the <<< button next to the Import Root Certificate field to select the root certificate (DER-encoded .
Chapter 5 — Network Support Tap ok to return to the Security page. LEAP (Cisco Lightweight EAP) LEAP is the Cisco Lightweight version of EAP. Use “LEAP” to configure the use of LEAP as an authentication protocol, select “Open,” “WPA,” “WPA2,” or “Network EAP” as an association mode, or assign “Network EAP.” Note that this defaults to the Network EAP. 1 Set 8021x Security as “LEAP,” then choose one of the following: • Set Association to “Open.” • Set Association to “WPA.
Chapter 5 — Network Support EAP-FAST (EAP-Flexible Authentication via Secured Tunnel) The EAP-FAST protocol is a client-server security architecture that encrypts EAP transactions with a TLS tunnel. While similar to PEAP, it differs significantly as EAP-FAST tunnel establishment is based on strong secrets unique to users. These secrets are called Protected Access Credentials (PACs), which CiscoSecure ACS generates using a master key known only to CiscoSecure ACS.
Chapter 5 — Network Support 3 If Allow Automatic PAC provisioning is checked, you can check: • Prompt before acquiring a new PAC for notification of any incoming PACs. • Prompt before replacing a PAC for notification whether to replace a current PAC with an incoming PAC. 4 Enter the Anonymous EAP-FAST Name as assigned for public usage. This outer identity protects your login name or identity. 5 Click ok to return to the Security page.
Chapter 5 — Network Support Check this box to detect and report client behavior suspected of being rogue APs. Once a rouge AP is detected, your CN3 Computer no longer associates with that AP until you perform a clean boot. Clear this box to solve AP connection problems that result when an AP gets put on the rogue AP list due to inadvertent failed authentications and not because it is a real rouge. • Enable mixed cell: Mixed cell is a profile-dependent setting.
Chapter 5 — Network Support A wireless network can be added either when the network is detected, or manually by entering settings information. To determine if authentication information is needed, see your network administrator. 1 Tap Start > Settings > the Connections tab > the Wi-Fi icon, then tap Add New . . . 2 Enter a Network name. If the network was detected, the network name is entered and cannot change. From Connects to, select to what your network is to connect.
Chapter 5 — Network Support 3 Do the following to disable WEP encryption: a Set Authentication to either “Open” if WEP keys are not required; or “Shared” when WEP keys are required for association. b Set Data Encryption to “Disabled.” 4 Do the following to enable WEP encryption: a Set Authentication to either “Open” if WEP keys are not required; or “Shared” when WEP keys are required for association. b Set Data Encryption to “WEP.
Chapter 5 — Network Support 5 Do the following to enable WPA authentication: a Set Authentication to “WPA.” b Set Data Encryption to either “AES” or “TKIP.” c Enter the new Network key: 6 Do the following to enable WPA authentication using a preshared key: a Set Authentication to “WPA-PSK.” b Set Data Encryption to either “AES” or “TKIP.” c Enter the new Network key.
Chapter 5 — Network Support 7 Do the following to enable WPA2 authentication: a Set Authentication to “WPA2.” b Set Data Encryption to either “AES” or “TKIP.” c Enter the new Network key: 8 Do the following to enable WPA2 authentication using a preshared key: a Set Authentication to “WPA2-PSK.” b Set Data Encryption to either “AES” or “TKIP.” c Enter the new Network key.
Chapter 5 — Network Support 9 Tap Next, select either “PEAP” or “Smart Card or Certificate” for the EAP type, then tap Properties to adjust its settings. Tap Finish to return to the Configure Wireless Network screen. From the Networks to access drop-down list, select “All Available,” “Only access points,” or “Only computer-to-computer” depending on the type of networks to which you connect. Tap ok to close this screen.
Chapter 5 — Network Support Use the Intermec Settings applet to do device configuration settings within the SmartSystems Foundation. Information about the Intermec Settings applet is in the Intermec Computer Command Reference Manual (P/N: 073529) available online at www.intermec.com. Information about the SmartSystems Foundation is available as an online help within the SmartSystems Console application. Select SmartSystems > Help in the console to access the manual.
Chapter 5 — Network Support These MIB files are either in the CN3 Management Tools or on the web via www.intermec.com: • INTERMEC.MIB Defines the root of the Intermec MIB tree. • ITCADC.MIB Defines objects for Automated Data Collection (ADC). • ITCSNMP.MIB Defines objects for Intermec SNMP parameters and security methods, such as an SNMP security IP address. • ITCTERMINAL.MIB Defines objects for parameters, such as key clicks.
Chapter 5 — Network Support Configuring with SNMP The community string allows an SNMP manager to manage the CN3 Computer with a specified privilege level. The default read-only community string is “public” and “private” is the default read/write community string. See the specific configuration parameter to find its OID. To configure the CN3 Computers using SNMP 1 Configure CN3 Computers for RF communications. 2 Determine the OID (Object Identifier) for the parameter to change. The Intermec base OID is 1.3.
I Index CN3 Mobile Computer User’s Manual - PRELIMINARY 157
Index Numerics 1D area imager reading distances, 6 2D area imager reading distances, 5 802.11 WPA authentication Zero Configuration, 151 WPA authentication with pre-shared key Zero Configuration, 151 WPA2 authentication Zero Configuration, 152 WPA2 authentication with pre-shared key Zero Configuration, 152 zero configuration WEP encryption, 150 802.1x authentication Funk, 133 802.1x security troubleshooting, 94 A AB8 batteries, 7 AB9 batteries, 7 Abstract Syntax Notation.1 See ASN.
Index Bluetooth applet, 89 address assigned to CK60, 89 devices, 88 enabling for SF51 scanner, 88 Bluetooth Audio applet Bluetooth, 107 Browsing the Internet Internet Explorer Mobile, 68 C Calendar all day events, 40 creating, 42 appointments adding a note, 44 assigning to a category, 45 changing, 42 creating, 42 deleting, 47 finding, 47 making recurring, 45 setting a reminder, 43 viewing, 41 categories, 39 meetings sending a request, 46 options changing, 47 Pocket Outlook, 38 recurrence pattern, 41 Start
Index Creating a modem connection to an ISP, 119 a VPN server connection to work, 124 a wireless network connection, 148 contacts via Contacts, 48 document via Word Mobile, 60 drawing via Notes, 30 note via Notes, 55 task via Tasks, 53 workbook via Excel Mobile, 63 D Detect rogue APs, 147 E EAP (Extensible Authentication Protocol), 130 EAP-FAST, 130 profile security information, 146 WEP encryption, 146 EAP-TLS, 141 EAP-Tunneled TLS, 142 EasySet creating an SF51 connection label, 88 scan bar code labels,
Index Installing applications Avalanche, 72 SmartSystems, 73 using a storage card, 72 using Secure Digital cards, 72 with ActiveSync, 71 Intermec Developer Library, 11 Intermec settings beeper volume, 154 Intermec Settings applet Bluetooth, 109 enable speaker, 15 Funk security, 131 set vibrator, 17 viewing SF51 information, 90 Intermec settings applet smartsystems, 11, 154 INTERMEC.
Index Notes adding to appointments, 44 contacts, 50 creating a note, 55 drawing on the screen, 30 creating a drawing, 30 selecting a drawing, 30 Pocket Outlook, 54 recording a message, 31 synchronizing notes, 55 writing on the screen, 28 alternate writing, 29 converting writing to text, 29 selecting the writing, 28 tips for good recognition, 29 O Object Store packaging an application, 70 Operating the CK60 troubleshooting, 92 P Packaging an application Flash File Store, 71 Object Store, 70 Secure Digital
Index Services Phone application GSM radios, 117 Settings applets Bluetooth, 88 Bluetooth audio, 107 intermec settings Bluetooth, 109 funk security, 131 SF51 scanner information, 90 wireless printing, 105 SF51 scanner configuring, 88 creating a connection label, 88 enabling Bluetooth Bluetooth enabling for SF51 scanner, 88 imager settings, 88 viewing information from CK60 computer, 90 Simple Network Management Protocol See SNMP SmartSystems, 11, 73, 154 SMS Folder behavior connected to email server, 57 SM
Index URLs ActiveSync, 36 MIBs, 155 Microsoft support, 22 Windows Mobile, 22 Windows Mobile support, 22 V Vibrator enabling via intermec settings applet, 17 enabling via sounds & notifications applet, 17 Viewing mobile favorites and channels Internet Explorer Mobile, 68 VPN server creating a connection to work, 124 W WAP pages, 66 connecting to an ISP, 119 Wavelink Avalanche, 72 Web pages, 66 connecting to an ISP, 119 WEP (Wired Equivalent Privacy) encryption, 129 WEP encryption EAP-FAST security method,
Corporate Headquarters 6001 36th Avenue West Everett, Washington 98203 U.S.A. tel 425.348.2600 fax 425.355.9551 www.intermec.
