Installation Instructions

ManualsBrandsInterflex Datensysteme Gmbh & Cokg ManualsElectronicsProximity reader

Proximity Reader P60-W01

Page

P-60-W01 10 / 2003

Proximity Reader P60-W01

Information to the User

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference receibed including interence that may cause

undesired operation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

n Reorient or relocate the receiving antenna.

n Increase the separation between the equipment and receiver.

n Connect the equipment into an outlet on a circuit different from that to which the

receiver in connected.

n Consult the dealer or an experienced radio/TV technician for help.

Caution

Changes or modifications not expressly approved by the Party responsible for compliance

could void the user's authority to operate the equipment.

Usage in Accordance with the Intended Purpose

The described proximity reader is used for reading data of proximity identification media. Any

other use is not permitted.

Interflex is not to be held responsible for damages caused by the use of the proximity reader.

Interflex reserves the right to make modifications without prior notification in the interest of

technical progress.

Summary of content (5 pages)

PAGE 1
P-60-W01 10 / 2003 Proximity Reader P60-W01 Information to the User This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference receibed including interence that may cause undesired operation.
PAGE 2
Installation Install the proximity reader next to the locking device in an unsecured area and connect the 1 connecting cable either directly or via extension cable to the access manager controlling and monitoring this access point. Installation Variants A B 1 4 max. 2m max. 100m 4 3 3 2 5 1a 1a 1 A 1 1a 2 3 4 5 1 Connection via extension cable Proximity reader Connecting cable Junction box with 10-pin terminal strip 1 10-wire, shielded cable in empty tube Access manager, e.g.
PAGE 3
Assembly B 1 2 C 1 4a green pink black grey white brown 1b LED GN LED RD SHIELD D 2/ CPS D 1/ DATA1 D 0/ DATA0 yellow BUZ blue GND red +5 V DC 1a REL K 1 10 9 8 7 6 5 4 3 2 1 42,4/ 1,66. 68,8/ 2,7 80,3/ 3,16 A 1a 1b CPU IC 1 REL K 2 14 J 6 1 S1 4 1100/ 43,31 20,4/ 0,8 40,8/ 1,6 4 3 A 1 1a 1b 2 3 Assembly Housing with MPU board Chamferings Connecting cable Cover Countersunk bolts B 4 4a Connection to access manager Access manager IF 0-610 Terminal strip Kl.
PAGE 4
How to Correctly Present the Identification Medium In order to permit a correct data capture, the identification medium must be presented within the specified range and in parallel to the proximity reader until the red or green LED lights up and a short “beep” can be heard (see figure).
PAGE 5
Technical Data Details Power supply: - Low-voltage: - Power consumption: Via the access manager 5 VDC, +/- 5 % Max. 100 mA Reader: - Type: - Frequency: - Interface: - Read range between identification medium and reader Proxif proximity reader 125 kHz Wiegand / MagCard / TTL asynchron The actual read range performance depends on the range of action of the antenna embedded in the identification medium. It may range up to 50 mm/ 5,00 cm”.